WDTV Forum - WDTV Media Player

WDTV 1 Forum Groups => Homebrew / Custom Firmware => Topic started by: Zorander on March 27, 2009, 06:03:32 AM

Title: *experimental* wireless usb support package
Post by: Zorander on March 27, 2009, 06:03:32 AM
Here's a first attempt at a wireless usb network support package.

wireless-mod.app.bin (0.0.1) (http://www.mediafire.com/?qtnczimmml2)

It attempts to load the usb network driver for the following chipsets:

The normal net.config options apply (dhcp/static IP).  The drivers should default to searching for the best open wireless point.

You can try adding specific configuration into net.config such as:

  iwconfig $MDEV essid MyHomeNetwork

No idea if wpa_supplicant works. (it's probably tied to the Otus driver explicitly)

This app.bin may work on older ext3-boot firmwares, as well as WDLXTV firmware releases. (UNTESTED)

Title: Re: *experimental* wireless usb support package
Post by: waterlooscp on March 27, 2009, 12:08:09 PM
Hello Zorander,

If I use encryption i have to put like this?

wconfig $MDEV essid MyHomeNetwork key xxxx-xxxx-x

Sorry but I'm Linux newbie.

Thanks for the package.

Regards

waterlooscp
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on March 27, 2009, 01:09:04 PM
I have a rt2500 wireless adapter to play with. I compiled the kernel modules a while ago, so I'll see about getting WDLXTV compatible with this package very soon.
Title: Re: *experimental* wireless usb support package
Post by: Zorander on March 27, 2009, 05:52:50 PM
wireless-mod experimental support package 0.0.2

Uploaded here (http://www.mediafire.com/?20mwwwnzz0r)

This version (attempts to) fix the /etc/mdev.conf for all the funky device names that they like to use.

Here's the list of network device names:
arusb_lnx uses ath0
rt2870sta uses ra0
rt73 uses rausb0
zd1201 uses wlan0
and, not to be outdone, zd1211b uses eth1 (or eth0)

I even threw in usb0 in case any of the regular usb network devices uses it (I think one or two of the usb-usb cables use usb0 as a device name)

b-rad.cc:  You need to update the /etc/mdev.conf in your distro to this:
Code: [Select]
# /etc/mdev.conf
eth[01] 0:0 755 *(/etc/hotplug/net.agent)
sd[a-z].* 0:0 755 @(/etc/hotplug/disk.agent)
sr[0-9] 0:0 0 *(/etc/hotplug/cd.agent)
#
# wireless drivers like to use strange device names
usb0    0:0 755 *(/etc/hotplug/net.agent)
ra0     0:0 755 *(/etc/hotplug/net.agent)
rausb0  0:0 755 *(/etc/hotplug/net.agent)
ath0    0:0 755 *(/etc/hotplug/net.agent)
vlan0   0:0 755 *(/etc/hotplug/net.agent)
(this is required since WDLXTV is perma-flashed, including the /etc directory where mdev resides, and therefore read only)
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 27, 2009, 09:47:40 PM
1st, thanks for the rt73 port on wdtv!!

I have a D-link DWA-110 wireless adapter (rt73 chipset), and installed the 8.7.2 and wireless-mod 0.0.2.

Apparently the kernel module does not detect the device, as follows:

 - Messages.txt during boot:
wdtv user.notice root:  [07d1:3c07] 1-1( 2.00,480m) 802.11 bg WLAN
(...)
wdtv user.info kernel: usbcore: registered new driver rt73
no further mention of rt73 nor WLAN

 - lsusb -v shows:
Displaying detected USB devices...
 [07d1:3c07] 1-1( 2.00,480m) 802.11 bg WLAN
 [0781:5203] 1-2( 2.00,480m) Flash Memory/200524446007F5F2E8BA
 [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
 [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI

The ifconfig and /proc/net/dev shows only the "lo" interface.
iwconfig shows no interfaces.

Tried to force load of rt73 on net.config, or others things...  but none worked.

If I unplug the wireless dongle and plug it again, the message.txt shows only:
wdtv user.info kernel: usb 1-1: USB disconnect, address 2
wdtv user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 4

Any Ideas?
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 28, 2009, 12:03:47 AM
my rt73 based edimax EW-7318USg works ok with wireless-mod 0.0.1, no more messages in messages.txt then loading rt73.ko, interface was down by default (0.0.2 should fix it), had to up by ifconfig rausb0 up and manualy set ip (ifconfig rausb0 ip) coz dhcp didn't work (0.0.2 should fix it too). then just used iwconfig to set ap and wep key (iwconfig rausb0 essid ap key "s:asciikey" and it works ok. also tried wpa-psk with wpa_supplicant.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 28, 2009, 01:19:41 AM
with 0.0.2 i got rausb0 up on reboot, but i can;t get iwconfig to work during boot setting ap/key in net.config, after boot when i run iwconfig from console it works ok, i get ip with dhcp.
Title: Re: *experimental* wireless usb support package
Post by: FUZZI on March 28, 2009, 01:26:42 AM
are there any good tutorials for total noobs how to install a custom firmware on the wd? I've got a RaLink 2870 usb adapter and it would be really great if this is going to work.‚
Title: Re: *experimental* wireless usb support package
Post by: Hades666 on March 28, 2009, 01:41:38 AM
are there any good tutorials for total noobs how to install a custom firmware on the wd? I've got a RaLink 2870 usb adapter and it would be really great if this is going to work.‚

Totally agree, a step-by-step guide will be very useful...
I find some guides for wired conections, but with wireless configuration i´m totally lost...

thanks
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 28, 2009, 03:23:56 AM
zorander: i looked on /etc/hotplug/net.agent and i think iwconfig fails on boot because it is executed before you up the interface, is it right or i'm wrong? maybe we should wake up interface before dhcp so if there will be iwconfig in the middle it should work.

edit: my mistake, rausb0 should be up before iwconfig, so still i don't know why it doesn't work from /boot/net.config while it works from console after boot.
Title: Re: *experimental* wireless usb support package
Post by: Zorander on March 28, 2009, 03:30:32 AM
rezmus: you're right.

Just add "ifconfig $MDEV up" to the net.config before the iwconfig lines should do for now.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 28, 2009, 04:52:30 AM
hehe so i was right after all, now it works like a charm :)
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 28, 2009, 07:28:20 AM
Zorander,

Concerning about the D-Link DWA-110 issues;

After some test and research, apparently for D-LINK DEVICES (vendor: 07d1) this port used for RT73 driver supports only the product: 3c03 ("DWL-G122 802.11g Adapter [ralink rt73]")"

The DWA-110 (07d1:3c07) is compatible with the rt73 driver, but in order to work with this port of RT73, its "usb product id" must be added to the rtmp_def.h of the RT73 files before compiling.
(just add {USB_DEVICE(0x07d1,0x3c07)},\ in rtmp_def.h )

Thats why the dongle gets detected on the lsusb, but the interfaces do not show up (the driver does not recognizes it as a valid/supported D-Link device).
wdtv user.notice root:  [07d1:3c07] 1-2( 2.00,480m) 802.11 bg WLAN

If it's possible, can you include this is some next release?
I would appreciate a lot!!!

Thanks for all this work!
Shadow
Title: Re: *experimental* wireless usb support package
Post by: 3dxr on March 28, 2009, 08:01:14 AM
Hi all I want ask people who have functional Wireless Dongle do some performance test

and share results and send me a private message to post where was this information published

I am not able check so many threads and update WIKI
I need your support now when is main discussion splitted to more forums and threads

I near future I will add to WIKI WIRELESS ADAPTERS TABLE


Regards

3dxr
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 28, 2009, 11:14:34 AM
zorander check this link:

http://cateee.net/lkddb/web-lkddb/RT73USB.html (http://cateee.net/lkddb/web-lkddb/RT73USB.html)

here u can find much more vids/pids for RT73 then in sources i've sent u if u consider to recompile the driver.
Title: Re: *experimental* wireless usb support package
Post by: Zorander on March 28, 2009, 07:35:10 PM
**UPDATE**  wireless-mod 0.3 released (http://www.mediafire.com/?dz1nmqloazm)

(special thanks go to rezmus--the web-lkddb was quite handy as a source of usbids, although there were still a handfull of ids in the zd1211b driver that were missing from lkddb)

Still missing:  RaLink 2x00 that are not in rt73 and are not 2870's.

Although I know that there are more devices supported by Linux 2.6.29, it would be EXTREMELY difficult to back-port them to 2.6.15 at this point.  There was a pretty big change around 2.6.24 that makes backporting difficult.  Unfortunatly, most of the soft-mac wireless drivers didn't make it into linux until after 2.6.24

The drivers in this modpack each have their own implementation of the 802.11 stack imbedded in them--that's why they are so large.  I've not been able to use the new ones from 2.6.24 or later that use the generic ieee80211 driver--the version included in 2.6.15 is basically useless (and none of the drivers included here use it).

Title: Re: *experimental* wireless usb support package
Post by: shadow on March 28, 2009, 09:33:02 PM
 
    > wireless-mod 0.3 released

   Thank you Zorander and Rezmus, now it works perfectly on my D-Link DWA-110!!

   Tomorrow I'll try the WPA stuff... :)

   Thanks!!Thanks!!Thanks!!Thanks!!Thanks!! :)
Title: Re: *experimental* wireless usb support package
Post by: peterskeetero on March 29, 2009, 01:28:32 AM
Hi Shadow,
I've downloaded ext3-boot-0.8.7.2 and want to update my stock
WDTV and connect my DWA-110 as well.
My network uses WPA2 - did you get that working with WDTV and your DWA-110 ?
I'm new to this as well and am dying to get ssh/ftp/samba access to my WDTV
as I've got a 2 TB USB enclosure connected and am sick of physically moving it between
TV room and computer room.
Thx,
Peter
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 02:33:18 AM
HI I have a Dlink wda 140 that I try to work. this is what I have done.
I have installed the ext, copied the opt files adn added the latest wlanbin ver3 on my usb stick.
I have then edit my net config file to use statick ipå etc..
I have tried the iwconfig line without adn with encryption no luck.
ifconfig $MDEV up
iwconfig $MDEV essid HJEMME iwconfig channel 6


I can see that my wlan usb blinks when the WDTV startup..
I am also trying ot ping, telnet to the device but with no luck. I am also cheking the wlan router to see if its "connected"

Log data..

This I find it is might usefull
Driver auto reconnect to last OID_802_11_SSID setting - HJEMME, len - 6
StaCfg.WepStatus=0, while pInBss->WepStatus=1
CntlOidSsidProc():CNTL - 0 BSS of 10 BSS match the desire (6)SSID - HJEMME
CntlOidSsidProc():CNTL - No matching BSS, start a new scan

nd then it starts to scan for chanels again and again..

ANy idea what the problem solution is?

Jackman
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 02:52:51 AM
I now tried to add the line channel 6 in my iwconfig to set the channel...
this is what happends it repeats itself.. continusly..I think.

SYNC - BBP R4 to 20MHz.l
SwitchChannel#1(RF=1, Pwr0=7, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07c6, R3=0x98168e55, R4=0x980dd20b
SwitchChannel#2(RF=1, Pwr0=8, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07c6, R3=0x98169055, R4=0x980dd21f
SwitchChannel#3(RF=1, Pwr0=8, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07ca, R3=0x98169055, R4=0x980dd20b
SwitchChannel#4(RF=1, Pwr0=9, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07ca, R3=0x98169255, R4=0x980dd21f
SwitchChannel#5(RF=1, Pwr0=9, Pwr1=7, 2T) to , R1=0x98402ecc, R2=0x984c07ce, R3=0x98169255, R4=0x980dd1cb
SwitchChannel#6(RF=1, Pwr0=10, Pwr1=7, 2T) to , R1=0x98402ecc, R2=0x984c07ce, R3=0x98169455, R4=0x980dd1df
SwitchChannel#7(RF=1, Pwr0=10, Pwr1=7, 2T) to , R1=0x98402ecc, R2=0x984c07d2, R3=0x98169455, R4=0x980dd1cb
SwitchChannel#8(RF=1, Pwr0=11, Pwr1=7, 2T) to , R1=0x98402ecc, R2=0x984c07d2, R3=0x98169655, R4=0x980dd1df
SwitchChannel#9(RF=1, Pwr0=11, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07d6, R3=0x98169655, R4=0x980dd20b
SwitchChannel#10(RF=1, Pwr0=12, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07d6, R3=0x98169855, R4=0x980dd21f
SwitchChannel#11(RF=1, Pwr0=12, Pwr1=8, 2T) to , R1=0x98402ecc, R2=0x984c07da, R3=0x98169855, R4=0x980dd20b
SwitchChannel#12(RF=1, Pwr0=13, Pwr1=9, 2T) to , R1=0x98402ecc, R2=0x984c07da, R3=0x98169a55, R4=0x980dd25f
SwitchChannel#13(RF=1, Pwr0=13, Pwr1=9, 2T) to , R1=0x98402ecc, R2=0x984c07de, R3=0x98169a55, R4=0x980dd24b
SwitchChannel#6(RF=1, Pwr0=10, Pwr1=7, 2T) to , R1=0x98402ecc, R2=0x984c07ce, R3=0x98169455, R4=0x980dd1df
SYNC - End of SCAN, restore to channel 6, Total BSS[11]
SCAN done, resume MSDU transmission ...
Driver auto reconnect to last OID_802_11_SSID setting - HJEMME, len - 6
StaCfg.WepStatus=1, while pInBss->WepStatus=0
CntlOidSsidProc():CNTL - 0 BSS of 11 BSS match the desire (6)SSID - HJEMME
CntlOidSsidProc():CNTL - No matching BSS, start a new scan
SCANNING, suspend MSDU transmission ...
SYNC - BBP R4 to 20MHz.l

Looking forward .. to fix this!!!
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 02:58:22 AM
I google and found out this form the forum.

that I have this chipset in my usb wlan.. and Dlink support pointed to this page.
USB (RT2870/RT2770)

http://www.ralinktech.com/ralink/Home/Support/Linux.html

Can it be a firmware problem on my usb  ???


Title: Re: *experimental* wireless usb support package
Post by: granjerox on March 29, 2009, 06:47:47 AM
It would be very nice if you get to work the rt2570 devices.

I have a Conceptronic C54RU
VID:PID -> 14B2:3C02

Officially it works with rt2570 driver but I've readed it could work with rt73.
I've tried it with ext3-boot release 0.8.7.2 and wireless-mod 0.3 but
without luck.

Thank U very much and go on with this incredible work !!
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 07:22:34 AM
From shadows post I understadn that we must "tell" linux that this hardware unit must use the spesific driver..
I have a Dwa-140 adn I found the following id info on this usb list.
http://www.linux-usb.org/usb.ids

07d1:3c09  DWA-140 802.11n Adapter [ralink rt2870]


Thanks for your help :D
Title: Re: *experimental* wireless usb support package
Post by: bmwhite on March 29, 2009, 09:13:56 AM
First off, thanks to all the work you guys/gals have done. In my younger days I would have dived in with you, but now I'm taker and not a giver. :)
I have been trying to get the wireless going. I have an Airlink AWL3026NA (ZD1211B) on USB1 that works fine at the computer. Router recognizes it. However it won't recognize it with the WDTV (for testing purposes it is also in the same room as the router and PC). On USB2 I have a thumb drive with ext3-boot.0.8.7.2 and wireless-mod.app.bin 0.3. The WDTV boots up with the modded firmware fine but no IP and router says nothing there. The router is set up with WEP 64-bit, my SSID is "WHITE" and my WEP-64 ASCII passphrase is "ABCDE". (I will make security stronger once I get it working). I have some question on network.config, is this right:
Code: [Select]
HOST=wdtv
ifconfig $MDEV up
iwconfig $MDEV essid WHITE key "s:ABCDE"
DHCP=yes

I have attached the messages.txt file. Doesn't look like anything wireless is sucessful. Any thoughts on why a no-go? Thanks in advance for any help.
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 29, 2009, 10:37:35 AM
bmwhite

  Apparently your WDTV getting some errors when it tries to initialize your wireless dongle. The log shows:

(...) wdtv user.err kernel: usb 1-1: device descriptor read/64, error -71
(...) wdtv user.err kernel: usb 1-1: device not accepting address 4, error -71

  Have you tried to reconnect or maybe change ports, to see if it works?
Title: Re: *experimental* wireless usb support package
Post by: waterlooscp on March 29, 2009, 10:53:06 AM
Hi all,

First of all, thanks for the excelent job.

I have a conceptronic c54 ru adapter. When I connect to the wdtv (ext3-boot-0.8.7.2 and wireless-mod 0.3) nothing happens, the lights are always off.

Anyone could confirm if at this time this adapter is compatible?

Device Descriptor:
bcdUSB:             0x0200
bDeviceClass:         0x00
bDeviceSubClass:      0x00
bDeviceProtocol:      0x00
bMaxPacketSize0:      0x40 (64)
idVendor:           0x14B2
idProduct:          0x3C02
bcdDevice:          0x0001
iManufacturer:        0x01
iProduct:             0x02
iSerialNumber:        0x00
bNumConfigurations:   0x01

Thanks for the help.

waterlooscp
Title: Re: *experimental* wireless usb support package
Post by: bmwhite on March 29, 2009, 10:56:01 AM
Shadow - thanks for the quick response. I have tried the dongle in USB1 and USB2 multiple times - still no-go :(. I get those error -71 messages you mention in all the log files. Maybe an unsupported dongle??

Does the network.config look okay? I wasn't sure about the order of the statements. But it sounds like it is not even getting that far, huh?
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 11:22:05 AM
Could someone look at my previous post and maybe help me ?
Any idea what is the problem? I seethat the wda-140 light is contstantly blinking red.

Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on March 29, 2009, 11:28:07 AM
Ok, did the few things required to get WDLXTV (http://b-rad.cc/wdlxtv) compatible with this. All the modules load, although I can't seem to get my rt2500 adapter to be recognized, kernel module loads but thats it. Might dig further into it soon.

Only one thing I'd like to propose:

I'd prefer not have to modify mdev.conf, so how about checking to see if the devices already exist inside of mdev and catting them on if not, like such.
Code: [Select]
[ "`cat /etc/mdev.conf | grep rausb0`" == "" ] && cat $APATH/etc/mdev.conf >> /etc/mdev.conf

this makes mdev.conf updateable without me having to whip up a new release for a new adapter.

Still tweaking out wdlxtv for the next release, but this will be in there...as well as one new feature I hacked in that a lot of people will appreciate :D
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 29, 2009, 11:33:49 AM
Could someone look at my previous post and maybe help me ?
Any idea what is the problem? I seethat the wda-140 light is contstantly blinking red.



seems your driver is working just can;t find essid, try "essid any" or make sure your ssid is broadcated.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 29, 2009, 11:41:24 AM
or try iwconfig $MDEV ap 00:11:22:33:44:55

replacing 00:11:22:33:44:55 with your wifi router/ap interface mac.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 12:42:27 PM
HI I am adding my last log files, I ma trying whitout key and whit key (natually changes it) in the ap. I have tried other channels (number1) in the api but it all seems to stop.. the usb key seems in one ocation to try and try and try but in the other setting, (all info in)
Title: Re: *experimental* wireless usb support package
Post by: waterlooscp on March 29, 2009, 01:20:44 PM
It would be very nice if you get to work the rt2570 devices.

I have a Conceptronic C54RU
VID:PID -> 14B2:3C02

Officially it works with rt2570 driver but I've readed it could work with rt73.
I've tried it with ext3-boot release 0.8.7.2 and wireless-mod 0.3 but
without luck.

Thank U very much and go on with this incredible work !!

Hi granjerox,
I have the same adapter as you and doesn't work. 
Your adapter turn lights on when connected to wdtv?

I have also a SMC2862W-G with the same behaviour.

Regards




Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 01:29:25 PM
HI I get red light on my dwa-140
I have set the mac asdress of my ap ,adn channel + key
and I can see that the mac adress form the USBWan tries to connect but do not get any ip assign. Because it is set in the config??

My ap is a 3com that cna max run on 22mb but my usbwlan key can run on 54 and it seesm from the log tha tit tries to do so.. any parameter to set for this?

addign my log and my config file

Thanks for the help in advance..
Title: Re: *experimental* wireless usb support package
Post by: Zorander on March 29, 2009, 05:03:06 PM
It would be very nice if you get to work the rt2570 devices.

I have a Conceptronic C54RU
VID:PID -> 14B2:3C02

Officially it works with rt2570 driver but I've readed it could work with rt73.
I've tried it with ext3-boot release 0.8.7.2 and wireless-mod 0.3 but
without luck.

Thank U very much and go on with this incredible work !!
Yea, I don't have the 25xx adapters working yet.

However, the 14B2:3C09 one that someone else has should work (it uses the rt2870sta driver).

Ok, did the few things required to get WDLXTV (http://b-rad.cc/wdlxtv) compatible with this. All the modules load, although I can't seem to get my rt2500 adapter to be recognized, kernel module loads but thats it. Might dig further into it soon.

Only one thing I'd like to propose:

I'd prefer not have to modify mdev.conf, so how about checking to see if the devices already exist inside of mdev and catting them on if not, like such.
Code: [Select]
[ "`cat /etc/mdev.conf | grep rausb0`" == "" ] && cat $APATH/etc/mdev.conf >> /etc/mdev.conf

this makes mdev.conf updateable without me having to whip up a new release for a new adapter.

Still tweaking out wdlxtv for the next release, but this will be in there...as well as one new feature I hacked in that a lot of people will appreciate :D
The problem is that /etc is READ ONLY in WDLXTV and the update command would just fail.
There are alternatives, that was just the fastest.  (I could chase down the line where the device gets named in the wireless driver and "fix" it, for one, or I could do a unionfs mount of /etc and my own directory to replace one or two files)

And right now, ralink 25xx adapters are known to NOT work (no working driver yet)

Title: Re: *experimental* wireless usb support package
Post by: shadow on March 29, 2009, 05:43:10 PM

 @peterskeetero

  Ok, after some hammering :) I got my D-Link DWA-110 working with WPA2-PSK / AES.

  Some strange behavior:
  *It fails to accept the ctrl_interface of the wpa_supplicant. It gives this error:
   Failed to initialize control interface '/boot/ctrl/wpa_supplicant'
   (the directory /boot/crtl exists, tried conf to /tmp/wpa_supplicant but same result)
   
   I workarounded this by commenting the #ctrl_interface on wpa_supplicant.conf. But would be good to use with crtl_interface (think that the network will work ok, but wpa_cli won't work without it).

   Another strange behavior:
   Network works fine (ssh, ping, etc the connections seems steady, but the Status led blinks a lot, even when there is no traffic. I checked the logs and there is *a lot* of this messages:

wdtv user.warn kernel: MlmeAssocReqAction(): WPA2/WPA2PSK fill the ReqVarIEs with CipherTmp!
wdtv user.warn kernel: calling linkdown

  Message repeats (sometimes only the 1st line, sometimes only the second).

  Any clues?

  My setup for WPA2-PSK AES is:

net.config (DHCP=Yes, added the following lines)
ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

create a wpa_supplicant.conf on the root of pendrive, with the following content:
#ctrl_interface=/boot/ctrl/wpa_supplicant
network={
   ssid="your_ssid"
   scan_ssid=1
   key_mgmt=WPA-PSK
   proto=WPA2
   pairwise=CCMP
   group=CCMP
   psk="your_passphrase"
}

Note: Not able to work with hidden essid (even with scan_ssid=1). When the essid visible it works just fine.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on March 29, 2009, 08:05:58 PM
It would be very nice if you get to work the rt2570 devices.

I have a Conceptronic C54RU
VID:PID -> 14B2:3C02

Officially it works with rt2570 driver but I've readed it could work with rt73.
I've tried it with ext3-boot release 0.8.7.2 and wireless-mod 0.3 but
without luck.

Thank U very much and go on with this incredible work !!
Yea, I don't have the 25xx adapters working yet.

However, the 14B2:3C09 one that someone else has should work (it uses the rt2870sta driver).

Ok, did the few things required to get WDLXTV (http://b-rad.cc/wdlxtv) compatible with this. All the modules load, although I can't seem to get my rt2500 adapter to be recognized, kernel module loads but thats it. Might dig further into it soon.
Only one thing I'd like to propose:

I'd prefer not have to modify mdev.conf, so how about checking to see if the devices already exist inside of mdev and catting them on if not, like such.
Code: [Select]
[ "`cat /etc/mdev.conf | grep rausb0`" == "" ] && cat $APATH/etc/mdev.conf >> /etc/mdev.conf

this makes mdev.conf updateable without me having to whip up a new release for a new adapter.

Still tweaking out wdlxtv for the next release, but this will be in there...as well as one new feature I hacked in that a lot of people will appreciate :D
The problem is that /etc is READ ONLY in WDLXTV and the update command would just fail.
There are alternatives, that was just the fastest.  (I could chase down the line where the device gets named in the wireless driver and "fix" it, for one, or I could do a unionfs mount of /etc and my own directory to replace one or two files)

And right now, ralink 25xx adapters are known to NOT work (no working driver yet)



Well what I wrote will work,  because I symlinked /etc/mdev.conf to /tmp where the stable mdev.conf resides. it just won't work until i've released the next revision. As I think of conf files that would benefit from dynamic modification I've done the same thing for them all.

I've inspected the latest ext3-boot there are modules in there that will have to be in the wireless pack as well to work with wdlxtv, they can't fit in wdlxtv because of size restrictions. I don't have many bytes to be working with.

I'll put a new version up tommorrow, then compile a wireless pack with everything that it should need and maybe someone here can test if it works. Too bad the rt2x00 drivers were mainlined, because its made it a bit difficult to backport them. Not even sure the legacy rt2500 driver even supports usb adapters.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 29, 2009, 08:26:46 PM
Hi could someone take a look at my last post adn my logfile and please try to see what the prolem is with my wlan usbstick?

Thanks.

Ole
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on March 29, 2009, 08:57:44 PM
Hi could someone take a look at my last post adn my logfile and please try to see what the prolem is with my wlan usbstick?

Thanks.

Ole

Code: [Select]
--> Error 2 opening /etc/Wireless/RT2870STA/RT2870STA.dat
that looks a bit suspect, as its the settings file for the driver. In the rt2500 driver I had define PROFILE_PATH inside of rt_config.h...could be causing it to choke. But it also doesn't appear to like your settings, maybe even ignores them altogether (which could be a settings issue again).

Title: Re: *experimental* wireless usb support package
Post by: eliafino on March 30, 2009, 01:37:19 AM
Hi at all!!!
great project  ;)

I read RaLink rt73 chipset is compatible (es. Dlink DWL-G122), i have DWL-G132 wich AR5005UG chipset. No support for this?

Is possible implement Multiband Atheros Driver for WiFi (MADWIFI)?

Best regards,
Elia
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 04:56:16 AM
I gave up the dwa-140  I tried to make it work and used soem hours.. since my WDTV is only 3 days old and the USB Wlan stick also I returned the wlanstick and asked to get anotehr ne I then got a cnet stick but it had not the right version so when I tested it it was like es, 3 time back to the shop and I bought a DWL.G122 (it even has a linux logo on the box) I pluged it in set the minimum of requierment like key and ssid , and auto dhcp and it was up running.

DWA-140 I cant recomend I have not manage to get it to work, but it seems for now that the DWL-G122 works fine.
Title: Re: *experimental* wireless usb support package
Post by: granjerox on March 30, 2009, 06:42:59 AM
Hi granjerox,
I have the same adapter as you and doesn't work. 
Your adapter turn lights on when connected to wdtv?

I have also a SMC2862W-G with the same behaviour.

Regards


Hi Waterlooscp,

hier same as you, lights remain off

:(
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 07:40:37 AM
D-Link Wlan stick adn USB hdisk. Not working togheter.
My new D-link DWL G122 works fine with a usbmemorystick. no problem.

but when I connect my 2,5 inc hdisk that is in a usb craddle Zynet hd-d3-u2 it do not work. HTe usb Disk seem to work fine.

Can this be a incompatible issue or power issue? Hdisk and USBWlan ?
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 30, 2009, 07:47:16 AM



   Another strange behavior:
   Network works fine (ssh, ping, etc the connections seems steady, but the Status led blinks a lot, even when there is no traffic. I checked the logs and there is *a lot* of this messages:

wdtv user.warn kernel: MlmeAssocReqAction(): WPA2/WPA2PSK fill the ReqVarIEs with CipherTmp!
wdtv user.warn kernel: calling linkdown

  Message repeats (sometimes only the 1st line, sometimes only the second).

  Any clues?


 Just an update:

 Seems that it actually looses some packets when the messages appears:
(tail -f messages.txt and ping wdtv from another machine)

on ping wdtv:
64 bytes from 192.168.2.101: seq=64 ttl=64 time=1.333 ms
64 bytes from 192.168.2.101: seq=72 ttl=64 time=6.259 ms
(packets 65 to 71 are missing)

right after packet 64 appears in messages.txt:
Mar 30 15:38:30 wdtv user.warn kernel: calling linkdown
Mar 30 15:38:30 wdtv user.warn kernel: MlmeAssocReqAction(): WPA2/WPA2PSK fill the ReqVarIEs with CipherTmp!

Or:
64 bytes from 192.168.2.101: seq=80 ttl=64 time=1.723 ms
64 bytes from 192.168.2.101: seq=81 ttl=64 time=857.369 ms
64 bytes from 192.168.2.101: seq=82 ttl=64 time=1.735 ms
(after packet 81 shown, the messages appears in messages.txt)


Title: Re: *experimental* wireless usb support package
Post by: shadow on March 30, 2009, 07:54:30 AM

D-Link Wlan stick adn USB hdisk. Not working togheter.
My new D-link DWL G122 works fine with a usbmemorystick. no problem.

but when I connect my 2,5 inc hdisk that is in a usb craddle Zynet hd-d3-u2 it do not work. HTe usb Disk seem to work fine.

Can this be a incompatible issue or power issue? Hdisk and USBWlan ?


 Jackman,

 Are you using a power adaptor for the HDD, or just the USB? Did the HDD spin?
 Maybe it's too much power drain for the USB on the WDTV to work with Wlan and a 2.5 HDD on USB...

 Maybe you should give a try with the power adaptor on HDD or with a external powered USB HUB...

 Regards
Title: Re: *experimental* wireless usb support package
Post by: 3dxr on March 30, 2009, 09:52:14 AM
USB2.0 bus capable provide 500mA
some 2.5" HDD like my reuiqre 2 times more (2x500ma=1A) or my Old TOSHIBA 2.5" 0.7A(700mA)

WIFI is active transmitting device this device is capable regulate power over tranmission but peek should be over USB bus limit.
Also USB descriptor are providing information about power min required capabilities and USBchip will reject device to prevent self damage. check your HDD how many require for full performance

becouse some devices are capable run in USB1.1 compatibility mode - are slower
and when is USB2.0 available working on high power mode (faster rotation hdd plates)

Solution is use WIFI HDD devices only on active external powered HUB
( its better buy good not cheap ... from ..... GOOD power adapter is required I = 5V/2Amp or more for example)

And I see you have packet lost on link
try decrease speed = this will change modulation on lower speed modes should be more resistable for noising from other wifi networks)
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 30, 2009, 10:52:03 AM

And I see you have packet lost on link
try decrease speed = this will change modulation on lower speed modes should be more resistable for noising from other wifi networks)


3dxr,

 I don't think that the speed is the problem, because this behavior occurs only when using WPA. If I use no encryption, it works just fine (ping ok, no kernel messages).
Also, when AP is using WPA all the other wireless devices on my network work ok (no interference, etc... Used kismet to choose a good channel).

The messages and network-hiccups with WPA occurs every 3 to 6 seconds... so my messages.txt is flooded with this..

 Anyone else is using wireless with WPA?? Any messages in messages.txt?
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 10:53:49 AM
Hi Is it so to understand that I canuse an USB hub that is powered adn connect the wland usba nd the hdisk?
How do I reduce the speed on the wlan to get less package loss?

This is what I founf out..
I looked around for a suitabel poweradapter and found a 5V adapter. this adapter work fine with the hdisk in windows..
Here is the strange things I experience with the WDTV.
If I connect the hardisk with power to the WDTV it wont boot.
If I turn on the wdtv (welcome screen) adn then connect the Hdisk, not mutch happend. but when I then remove the Original power the WDTV still runs. (getting power from my power in the hdisk)

I have attached the different logfiles to show how the system respond(or not reposnd) if it can be of interest for someone :D

Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 11:23:47 AM
Telent pasword? I can not find the default pasword anyplace, I am trying wiht enter and root as pasword but I am not able to acess.
Please help me.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 11:25:01 AM
Has anyone a working solution for USBwlan and a hardisk? If so what type of hdisk are you using? Anyone with a Dlink 122 Wlan ?

Thanks for all the help so faar.

J
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 30, 2009, 11:42:07 AM
shadow: i'm using wpa-psk on rt73 based wlan without such probs, but i don;t force wpa2 and ccmp algo.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on March 30, 2009, 01:15:26 PM
 :) Got myself a ZD1211b stick (ICIDU EUR 9.95 at mycom.nl) and it worked out of the box with ext3-boot-0.8.7.2 with wireless.app.bin 0.3

 :o amazing how you guys got this to work!!

Then I started to fidle around a bit and now my WD TV keeps crashing. I now have a green screen of death but can still telnet in. So lets try a reboot by telnet.

Ok, reboot got me up and running again.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 01:33:38 PM
Hi si anyone using a usb disk and a usb wlan simultainously ? Or are you guys streaming dataover the network for networks disks?
Title: Re: *experimental* wireless usb support package
Post by: draadloos on March 30, 2009, 01:36:11 PM
 ;D I got this setup:

on my network (a dead cheap SWEEX LC000070 wireless router), hardwired:
-NAS, WD Mybook World Edition with I guess, a samba share of 500gb
-PC with regular HD inside
and wireless:
-LAPTOP
-and tada: WDTV with ext3-boot-0.8.7.2 & wireless.app.bin 0.3 and ZD1211b usb stick by ICIDU

I fixed net.mounts to show my PC, the WD Mybook World Edition and LAPTOP:
xmount //192.168.123.179/SharedDocs PC cifs user=xxx
xmount //192.168.123.157/SharedDocs LAPTOP cifs user=xxx
xmount //192.168.123.123/public NAS1 cifs user=xxx,pass=xxx

So far I disabled all security on the router for ease of setup. Will try with WEP later.
I can see all mounted shares on PC, NAS and LAPTOP with files and subfolders.
 8)I am watching a movie Miami Vice in XVID  **wireless** without any problems.

The movie is about 800MB;s:
>  ³²²³    AUDiO......[ MP3 48000Hz 112kb/s CBR (2 chnls)                    ³²²³
>  ³²²³    ViDEO......[ 727 kbps XviD  23.976 FPS                            ³²²³
>  ³²²³    Q. FRAME...[ 0.223 bits*pixel                                     ³²²³
>  ³²²³    RESOLUTiON.[ 580 x 234 (2.479 (57:23))                            ³²²³
>  ³²²³    XViD DATE..[ 11/10/2006                                           ³²²³
>  ³²²³    SUBS.......[ None                                                 ³²²³
>  ³²²³    FiLES......[ 1                                                    ³²²³
>  ³±±³    SiZE.......[ 799 MB                                               ³±±³
>  ³°°³    SOURCE.....[ NTSC DVD  
Title: Re: *experimental* wireless usb support package
Post by: 3dxr on March 30, 2009, 01:39:38 PM

And I see you have packet lost on link
try decrease speed = this will change modulation on lower speed modes should be more resistable for noising from other wifi networks)


3dxr,

 I don't think that the speed is the problem, because this behavior occurs only when using WPA. If I use no encryption, it works just fine (ping ok, no kernel messages).
Also, when AP is using WPA all the other wireless devices on my network work ok (no interference, etc... Used kismet to choose a good channel).

The messages and network-hiccups with WPA occurs every 3 to 6 seconds... so my messages.txt is flooded with this..

 Anyone else is using wireless with WPA?? Any messages in messages.txt?


Try WEP64 Wpa_supplicant should be issue
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 30, 2009, 01:47:15 PM
Hi si anyone using a usb disk and a usb wlan simultainously ? Or are you guys streaming dataover the network for networks disks?

I'm using:

 WDTV USB1 -> Seagate 1TB (3.5" with external power supply)
 WDTV USB2 -> USB HUB (4 PORTS)
 
 USB HUB PORT1 -> Sandisk 256M - Pendrive (ext3-8.7.2)
 USB HUB PORT3 -> D-Link DWA-110

 All working fine so far.

 
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 30, 2009, 02:39:03 PM
I'm using:

 WDTV USB1 -> Seagate 1TB (3.5" with external power supply)
 WDTV USB2 -> USB HUB (4 PORTS)
 
 USB HUB PORT1 -> Sandisk 256M - Pendrive (ext3-8.7.2)
 USB HUB PORT3 -> D-Link DWA-110

K so in general youuse the USB memory as a "boot disk" adn the rest goes over a HUB that is powered..k and the unit that need extra power is then powered themself..
Gets to be a lot of cables and wiers. Not as neat as the origianl thing.

And also the toal price rice quite a lot, WDTV+USBHUB+WLAN...

Not to be negative because I love the fact that someone cna make additional features with the firmware. but what is now with your solution the big diffrence between a POPCORN adn the WDTV?
Sorry for my incompetens..

:D
Title: Re: *experimental* wireless usb support package
Post by: shadow on March 30, 2009, 03:51:47 PM
 @ rezmus
 @3dxr

shadow: i'm using wpa-psk on rt73 based wlan without such probs, but i don;t force wpa2 and ccmp algo.

Try WEP64 Wpa_supplicant should be issue

Thanks for your help, everything is working now with WPA2-PSK and AES.

As rezmus said everything is working on his rt73, I decided to make a fresh new start on mine.. Maybe I'd broke something during my previous tests  :-[.. So I erased the pen drive, installed ext3-8.7.2 and wireless 0.3... AND set a wpa_supplicant conf that does NOT force WPA2 and CCMP (thanks rezmus for this one  ;) ). Then, power up, and everything worked!!!! No more hiccups or kernel messages!!

When I got some transfers stats I'll post then!

Thanks!Thanks!Thanks!Thanks!Thanks!  ;D
Title: Re: *experimental* wireless usb support package
Post by: rezmus on March 30, 2009, 10:15:27 PM
Gets to be a lot of cables and wiers. Not as neat as the origianl thing.

And also the toal price rice quite a lot, WDTV+USBHUB+WLAN...

Not to be negative because I love the fact that someone cna make additional features with the firmware. but what is now with your solution the big diffrence between a POPCORN adn the WDTV?
Sorry for my incompetens..


there is no need for hub, some ppl use:

- usb hdd to boot up (with small fat32 partition for firmware, and ext2 for data)
- (w)lan usb

also when u buy pch u have to pay extra for wlan stick right? so the only difference in price is difference between pch and wdtv price.

shadow: i've got arround 12mbps, saw zorander had same.
Title: Re: *experimental* wireless usb support package
Post by: peterskeetero on March 30, 2009, 11:35:49 PM
Hey shadow thats great news !

So would your wpa_supplicant look like this now ?

network={
   ssid=yyyyyyyyyyy
   scan_ssid=1
   key_mgmt=WPA-PSK
   psk=xxxxxxxxxxxxxxxx
}

thx
Title: Re: *experimental* wireless usb support package
Post by: draadloos on March 30, 2009, 11:59:22 PM
When I switch off by remote control I can turn my wireless-WDTV on again. When I switch off and disconnect the power cord and then put the power on again, my wireless-WDTV seems to hang on the WDTV-logo. I can see activity on the usb stick from the green led but not on the wlan-adapter. I waited for say 10 min with the blue WDTV staying on screen and then pulled the power plug and put it back in again (power off with rc had no effect). I then have activity on usb-stick and wlan-adapter but OSD does not get past blue WD TV logo. I am able now to telnet in and only when I reboot from telnet I see normal boot-up procedure and wireless-WDTV ready to go. Whats going wrong?  ???
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 31, 2009, 07:58:22 AM
I am not sure what this can be but try this first.
disconnetc tht eusb wlan stick and see if you get the unit to boot.
If not remove the powert put the usb stick into the other USB port adn connect the power. (to test the USB ports)
WHat type of USB WLan stick do you have?

What version of the EXt3 do you use?
Have you remembert to copy the app.bin files for the wireless on the root of the stick? (I dont think this is the issue)

Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 31, 2009, 01:23:18 PM
I founf the problem wiht my USB HDISK the power adpater I used for the hdisk is not working correctly so therefore the WDTV turns itself off to prevent damage. I used the new poweradapter intended to be used whith the USB HUB instead in the USB Hdisk. and it works fine. I seems that the system is a bit slower for loading but Iguess thatst the speed different between USB stick adn USB hdisk.

Does anyone here knwo if any of the WD USB hardisk needs ectra power ? I am thinking of buying one soon when I have some cash and connect it to the powered USB hub (I expect it will get enoughf power from the hub)

Any experience?
Title: Re: *experimental* wireless usb support package
Post by: bmwhite on March 31, 2009, 04:13:45 PM
I use the WD My Passport (the 400 GB was on sale for $99 at Best Buy). The WDTV comes with a holder for it.  It is USB powered and doesn't even have a power connector. It works fine plugged directly in the WDTV. I then have an unpowered hub that connects 1) the ethernet adapter and 2) the flash drive that has the ext3 software. Don't get the less expensive My Book. They require external power and are much bigger. You want the Passport, the thing is really small compared to my Seagate FreeAgent drive. Its smaller than the WDTV.

I have also done the trick of making a small FAT partition on the WD Passport drive and storing the ext3 code there. That way you don't even need a hub. One WDTV port for the Passport and the other one for the USB ethernet adapter.

Also - to make this reply "on-topic"  :) I could never get my Airlink wireless dongle to work (see earlier post by me where I posted log file). Has anyone got an Airlink wireless dongle to work? Also I had asked a question about the order of statements in the network.config file but no response. Could someone post their complete network.config file for a WEP setup? Thanks!!
Title: Re: *experimental* wireless usb support package
Post by: Jackman on March 31, 2009, 11:20:48 PM
Hi the wlan config is very easy infact ot set up.
The first USB wlan I had was a D-link GWA140 adn I manage  get teh WDTV find the usb and so but in theend it did not work.
I then Drove to the shop and bought an DWL-122 from D-Link it cost about 40 dollar(I was proberøy ripped off ) and I then checked my config adn did the following.

Its is 3 lines that are important,
1 line that you start the USb device.
Second line is that you set the Network name and pasword. ( I am using wep but many has manage to get it workig with WPA.
3 is that you first try DHC normal.

You will find the setting you need in this post..

IF not send me a person message with your confi net and I will check it out.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on March 31, 2009, 11:43:07 PM
here is my net.config using rezmus's wireles walk-through
@ hxxp://www.avsforum.com/avs-vb/showthread.php?p=16144003#post16144003


#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# I added these 2 ixconfig-lines from rezmus's wireles walk-through
# @ hxxp://www.avsforum.com/avs-vb/showthread.php?p=16144003#post16144003
# the x's after essid is the name for your wlan and the x's in quotes is the WEP-key in hexadecimal.
# (for WEP-key in ASCII put s: in front of key: "s:xxxxx")
ifconfig $MDEV up
iwconfig $MDEV essid xxxxx key "xxxxxxxxxx"     

# attempt to set jumbo frames
# MTU=9000
# Your other computers should have same MTU or it will break NFS


#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

#NTP=pool.ntp.org
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 01, 2009, 02:14:21 AM
yep it looks very mutch as mine.
WHat firmware are you using? can you also post the log, it porberly give of these Linux wizard some meaning.

You can natually to use statick IP. if that does work. try to go back to the dynamic ip and add this to the iwconfig

iwconfig $MDEV ap 11:22:22:33:44 essid xxxxx key "xxxxxxxxxx"

this ap xx:xx:xx:xx:xx is actualy pointing to the AP mac adress os it must be replaced wiht the rihgt adress :D

I tried for hours to get a wlan USb to work and I gave up, I then returned it in the shop and bought one I knew people got to work here in the forum.
first atemt.   up running
Title: Re: *experimental* wireless usb support package
Post by: bmwhite on April 01, 2009, 04:12:05 AM
Thanks all. My config was the same so my dongle must be unsupported. It has the ZD1211 chip but must be something else about it. For now I am using the wired Trendnet USB adapter attached to a wireless gaming adapter. Works, but too much hardware and wires. I like the clean setup a wireless dongle would give.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 02, 2009, 03:56:09 AM
 ;D Upgraded to FW 1.02 and ext3 0.9 and got my wireless up and running again.

@Zorander: flash drive in USB1 and WLAN in USB2 works fine but flash in USB2 and WLAN in USB1 not. Any ideas why? My setup looks better with WLAN in USB1 ;)
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 02, 2009, 04:02:32 AM
@Zorander: after upgrading I no longer need to login for telnet. Is this due to FW 1.02 or ext 0.9?
Title: Re: *experimental* wireless usb support package
Post by: Zorander on April 02, 2009, 05:25:51 AM
@Zorander: after upgrading I no longer need to login for telnet. Is this due to FW 1.02 or ext 0.9?

It's because of a missing symlink.
If you type "cd /bin && ln -s busybox login" it should fix itself. (you may need to reboot for this to take effect)

It affects ssh logins as well (ssh doesn't work unless /bin/login exists)

ir_remap didn't make it into this version either (there's an app.bin for that anyway)

However, ftp and samba should both be working with this version.
Title: Re: *experimental* wireless usb support package
Post by: Kater432 on April 03, 2009, 09:14:39 AM
Hello,
i use a MSI US54SE WLAN USB Dongle. 
zd1211b   vendor_id = 0ace    product_id = 1215
ext3-boot-0.8.7.2 ---- wireless-mod-0.3.app.bin
it only works with wep, not with wpa.

WEP Config (Works without any Problems)
Code: [Select]
ifconfig $MDEV up
iwconfig $MDEV essid K9_K10_CHR1203FR2812 key "6162636465666768696A6B6C6D"

WPA Config (i only delete the two lines for wep and put this
Code: [Select]
ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

wpa_supplicant.conf
Code: [Select]
ctrl_interface=/boot/ctrl/wpa_supplicant
network={
ssid="K9_K10_CHR1203FR2812"
scan_ssid=1
key_mgmt=WPA-PSK
psk="my code in ascii"
}
on the tv screen it shows me the ip, but no ping are possible.
if the first line "ctrl_interface=/boot/ctrl/wpa_supplicant" are uncomment or like /tmp/wpa_supplicant no ip appear.
in my fritzbox i changed the wep to wpa-psk with tkip
Has someone a idea, or can someone put her his lines that works.
LOAD=zd1211b or modprobe zd1211b need in the net.config ???

thx
Title: Re: *experimental* wireless usb support package
Post by: shadow on April 03, 2009, 07:13:13 PM
@Kater432

  My wireless connection works with WPA only if I comment the "ctrl_interface" line in the wpa_supplicant.conf

  Have you tried this:

#ctrl_interface=/boot/ctrl/wpa_supplicant
   network={
   ssid="K9_K10_CHR1203FR2812"
   scan_ssid=1
   key_mgmt=WPA-PSK
   psk="my code in ascii"
   }

Note: My wireless network work in WPA2-PSK / AES... But with ssid VISIBLE.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 04, 2009, 12:27:20 AM
Anybody knows if it is possible to monitor wlan signal strength? I want to optimize wlan connection by positioning the adapter with usb extension cord and some signal monitoring would make things a lot easier.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 04, 2009, 06:51:40 AM
Found a wlan monitoring tool myself  :P

Snooping around in Zorander's wireless-mod-bin 0.3  i found this usefull wireless network monitoring tool in /apps/wireless-mod/bin/:

/apps/wireless-mod/bin/iwconfig eth0     

This utility shows current wlan configuration. It helped me in finding the optimal position (using a usb extension cord) for the WLAN-adapter. Mine looks like this (while streaming a movie):

root:~> /apps/wireless-mod/bin/iwconfig eth0
eth0      802.11b/g NIC  ESSID:"xxxxx"
          Mode:Managed  Frequency=2.462 GHz  Access Point: 00:xx:xx:xx:xx:xx
          Bit Rate:54 Mb/s
          Retry:off   RTS thr=9999 B   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:100/100  Signal level:89/100  Noise level:0/100
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:28761  Invalid misc:12120   Missed beacon:0


Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 04, 2009, 02:55:58 PM
Hi all,
just bought my WDTV today and have been reading forum posts all day long. What I am really interested in is to get WLan working. As I have read there are only a few USB Sticks that are supported. This seems to be a Kernel issue. I am really not a linux guru so I really don't know why other USB-Wlan-Sticks can't be used. But I remember there used to be a way to use unsupported Wlan sticks in linux using ndiswrapper. Is this maybe a possibilty to use other Wlan-Sticks?
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 04, 2009, 10:45:29 PM
What appears to be a limited number of wlan adapters is actually a few wlan drivers representing  a very large number of currently available working units. See the long list in the wdtv wiki. The zd1211b drivers is probably used in most cheap wifi usb sticks. My advice is find the cheapest adapters available in your neighbourhood and see which of these have zd1211b driver (if your friendly parts dealer cant tell, Google will ;) ). Once i got the right stick i was up and running within one hour. See my posts above in this forum.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 05, 2009, 03:11:25 AM
get something on rt73 or zd1211b, they are checked with wdtv and 100% working.
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 05, 2009, 04:45:09 AM
My Wireless Lan supports 802.11n and I was just thinking(dreaming) of the possibility to Stream HD to the WDTV over wlan 300Mbs. All the Sticks that are supported (rt73 and zd1211b chipset) only go 54Mbs. And I don't know if that is enough for HD-Streaming. Just for my understanding is it at all possible to use other chipsets without having to get a new kernel? I am already planning to get a supported usb wlan stick but just want to understand the difficulties.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 05, 2009, 05:12:32 AM
with so called 54mbit sticks we get on wd arround 12mbps, same stuff with wired gigabit adapters (for now ppl was able to get max 60mbps).
Title: Re: *experimental* wireless usb support package
Post by: deffie on April 05, 2009, 11:26:26 PM
Hi all,
i'm using ext3-boot and wireless-mod-app.bin,
after boot wireless card blinks slowly (3sec delay) here you can see relevant messages from log,
any hint ?

Thank you,
Giacomo.


Jan  1 00:00:34 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:00:34 wdtv user.notice kernel: vendor_id = 0105
Jan  1 00:00:34 wdtv user.notice kernel: product_id = 145f
Jan  1 00:00:34 wdtv user.notice kernel: USB 2.0 Host
Jan  1 00:00:34 wdtv user.notice kernel: Release Ver = 4330
Jan  1 00:00:34 wdtv user.notice kernel: EEPROM Ver = 4810
Jan  1 00:00:34 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:00:34 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:00:34 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:00:34 wdtv user.err kernel: PA type: 0
Jan  1 00:00:34 wdtv user.warn kernel: RFMD RF
Jan  1 00:00:34 wdtv user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:00:34 wdtv user.debug kernel: zd1205_config: EEP(HWFeature)=0x0
Jan  1 00:00:34 wdtv user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:00:34 wdtv user.warn kernel: Region:48
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:34 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:00:34 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.0.11 GW=192.168.0.20
Jan  1 00:00:35 wdtv user.notice root: Testing static IP assignment...

....snip....

Jan  1 00:00:40 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:00:40 wdtv user.warn kernel: jiffies = -259180, lastSetBusy = -264581, HZ=1000
Jan  1 00:00:40 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:00:40 wdtv user.warn kernel: jiffies = -259062, lastSetBusy = -264581, HZ=1000
Jan  1 00:00:41 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:00:41 wdtv user.warn kernel: jiffies = -258945, lastSetBusy = -264581, HZ=1000
Jan  1 00:00:41 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:00:41 wdtv user.warn kernel: jiffies = -258827, lastSetBusy = -264581, HZ=1000
Jan  1 00:00:41 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:00:41 wdtv user.warn kernel: jiffies = -258710, lastSetBusy = -264581, HZ=1000
...and continues like this...
Title: Re: *experimental* wireless usb support package
Post by: sksaustin on April 06, 2009, 08:48:36 AM
Hi!

I´m from germany.. excuse for my bad english. :)

I have a old WLAN Stick.. the DLink DWL-G122.
What i have read by now, the stick can be used and work on the WDTV.

I have flash the ext3 boot 0.9 and have the USB Stick on USB2 and the DLink Stick on USB1, but nothing worked.

My messages.txt have the following output...
Code: [Select]
Jan 1 00:00:41 wdtv user.warn kernel: idVendor = 0x7d1, idProduct = 0x3c03
Jan 1 00:00:41 wdtv user.notice root: net.agent: Called for rausb0
Jan 1 00:00:41 wdtv user.info kernel: usbcore: registered new driver rt73
Jan 1 00:00:42 wdtv user.warn kernel: => usb_rtusb_open
Jan 1 00:00:42 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan 1 00:00:42 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan 1 00:00:48 wdtv daemon.notice statd[1237]: Version 1.1.5 Starting
Jan 1 00:00:48 wdtv daemon.notice statd[1237]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan 1 00:00:51 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan 1 00:00:51 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)

These are only a few lines, if yomething want more i can post all.
The Device ID and Vendor are the ones frome Line1.

I have try it with a Open WLan AP, and also with WEP and WPA. nothing works.mh
My Router is an Asus WL-500gp V2.

Maybi someone have a hint for me.

thanx
sksaustin
Title: Re: *experimental* wireless usb support package
Post by: kaisersoze on April 06, 2009, 09:35:34 AM
I have tried to get this to work wit WDLXTV 0.4 (is this possible anyway? should be right?) and Atheros AR5007UG

These are my settings, wlan adapter blinks on/off 3 sec. interval:

net.config

# WPA INSERTS:

ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

# Dynamic IP Configuration:

DHCP=yes

# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.1.104
#GW=192.168.1.1
#NM=255.255.255.0
#DNS1=192.168.1.1
#DNS2=192.168.1.1

wpa_supplicant.conf
#ctrl_interface=/boot/ctrl/wpa_supplicant
network={
   ssid="CHN"
   scan_ssid=1
   key_mgmt=WPA-PSK
   proto=WPA2
   pairwise=CCMP
   group=CCMP
   psk="*********"
}

any help is very much appreciated!
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 06, 2009, 09:39:13 AM
   #scan_ssid=1
   #proto=WPA2
   #pairwise=CCMP
   #group=CCMP

turn ssid broadcast on.

btw: some of the cards can set wpa with iwpriv commands without need for wpa_supplicant, google for it.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 06, 2009, 11:52:30 AM
As faar as I know is not the wlan for WDLXTV working for the moment.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 06, 2009, 08:12:21 PM
I have tried to get this to work wit WDLXTV 0.4 (is this possible anyway? should be right?) and Atheros AR5007UG

/boot doesn't exist in wdxltv.

Try it without any security and see if you can connect, but jackman could not.

As faar as I know is not the wlan for WDLXTV working for the moment.

I just went out and bought an adapter today to get this working...and bought the wrong frackin one : \ I'll try and get back over there sometime soon.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 06, 2009, 08:56:17 PM
i will check it later today with wdlxtv, have both wire and wifi so i can see exectly what is going on ;)
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 06, 2009, 09:30:14 PM
i will check it later today with wdlxtv, have both wire and wifi so i can see exectly what is going on ;)

Zoranders pack is missing a handful of libraries that wdlxtv needs.

heres (http://rapidshare.com/files/218374138/wireless-mod-wdlxtv.app.bin) a wireless-mod-wdlxtv that contains everything (i think)

its ext2, so you can modify the files in /apps/wireless-mod-wldxtv to see if you can massage it into working.

Thanks for the help.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 07, 2009, 12:01:33 AM
will try this wdlxtv-wireless app later today
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 07, 2009, 12:06:49 AM
btw, anybody tried a Belkin N1 router with Atheros Otus driver? I read somewhere this driver also supports N1. Maybe this will help increase wireless throughput.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 07, 2009, 04:53:39 AM
My DWL-122 works fine for some time. I trasfeered a large file ot the device adn after soem time it stopped. I also tried to ping the WDTV but no connection. ANy idea?
I am using the latest EXT firmware
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 07, 2009, 05:54:45 AM
Cant use wlan, Have any of you experience that you turn the WDTV on adn everything works fine adn then next time you turn the deviec on (removing and inserting power) things dosent work.. like now my wlan wont start.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 07, 2009, 08:58:22 AM
Cant use wlan, Have any of you experience that you turn the WDTV on adn everything works fine adn then next time you turn the deviec on (removing and inserting power) things dosent work.. like now my wlan wont start.

Same here. After pulling the plug my wireless setup takes three times plugging in before it shows the ip address and the wireless connection is made.  ???  I know now it takes three times so I got used to it. I cant compare the message.txt logs for these three bootups as only with the 3rd one I can connect.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 07, 2009, 09:06:25 AM
Cant use wlan, Have any of you experience that you turn the WDTV on adn everything works fine adn then next time you turn the deviec on (removing and inserting power) things dosent work.. like now my wlan wont start.

Same here. After pulling the plug my wireless setup takes three times plugging in before it shows the ip address and the wireless connection is made.  ???  I know now it takes three times so I got used to it. I cant compare the message.txt logs for these three bootups as only with the 3rd one I can connect.

http://b-rad.cc/log-saver.app.bin
Title: Re: *experimental* wireless usb support package
Post by: kaisersoze on April 07, 2009, 10:07:48 AM
I have wdlxtv 0.4 working with wireless mod. Not yet with WPA but that should be possible with 0.4.0.2 right?

I have two questions maybe you guys are willing to help:

- wireless mod only works with FAT32 usb stick, not with my 1TB NTSF MyBook (WD) anyone know why or solution?
- When I connect a usb hub (cheapo chinese thing) without seperate AC-adapter the device connected aren't recognized. Will this work if I use USB hub with adapter??

Thanks!
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 07, 2009, 10:10:36 AM
HI I had this problem I also had problems with gettign the external hdisk showing.

The solution was simple but yet hard ot fidn out because things arent 100% like on a PC.

TO make my dwl-122 Wlan stick and my USB Iomega320G hdisk I had to do the follwing.

USB1: Connected to my Usbstick8G its just convinient and I think it is a bit faster thatn my USBHdisk.
USB2: MY 4 port USB HUB with Power

USBHUB USB1: connected to my Hdisk and with ecternal power. I tried severa time to get it to run adn not use power but use te USB Split cable to get more power. THis did not work at all so I am using now a normal USB cabel to the Hdsik NO SPLIT cabel.Format Fat32
USBHUB USB3: Connected my Wlan stick. The actual port is less important.
The clue was as I thought to get enoughf power to all external devices.

I am using EXT3 firmware since I am not able at this point to get the Wlan working whit b-rad 's firmware
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 07, 2009, 10:21:17 AM
I have wdlxtv 0.4 working with wireless mod. Not yet with WPA but that should be possible with 0.4.0.2 right?

I have two questions maybe you guys are willing to help:

- wireless mod only works with FAT32 usb stick, not with my 1TB NTSF MyBook (WD) anyone know why or solution?
- When I connect a usb hub (cheapo chinese thing) without seperate AC-adapter the device connected aren't recognized. Will this work if I use USB hub with adapter??

Thanks!

i;ve managed to run wpa on wdlxtv 0.4.2, but had some probs getting it work on boot, will do some more tests in the evening. i used ac hub without probs until it got burned yesterday =) today i bought cheap passive one and it works ok with wire usb lan and 2 x pen in.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 07, 2009, 11:41:00 AM
i;ve managed to run wpa on wdlxtv 0.4.2, but had some probs getting it work on boot, will do some more tests in the evening. i used ac hub without probs until it got burned yesterday =) today i bought cheap passive one and it works ok with wire usb lan and 2 x pen in.

something that might help you, the init.d script has two important variables accessible:

Code: [Select]
$AROOTthis is the location on the wdtv that the app.bin itself resides, for example /tmp/media/usb/sda2  or /tmp/mnt/sda2

Code: [Select]
$APATHthis is the location the app.bin is mounted, so here it would be /apps/wireless-mod-wdlxtv/

So inside the init.d script if you add something like this:

Code: [Select]
[ -e $AROOT/wpa-supplicant.conf ] && cp $AROOT/wpa-supplicant.conf /tmp
and inside of your net.config add

Code: [Select]
wpa_supplicant -Bw -Dralink -irausb0 -c/tmp/wpa-supplicant.conf
Then things should work (or get closer to working)

I'll be exhanging my adapter tmr, and can then help you guys out if its not figured by then.


Title: Re: *experimental* wireless usb support package
Post by: deffie on April 07, 2009, 12:49:51 PM

http://b-rad.cc/log-saver.app.bin


Thank you for these packages, please note that those download locations are not linked from your site, i searched deeply wireless-mod before finding it here.

Thank you and keep up the good work!

P.S If you want i can offer you (and the wdtv community) an ftp drop box or full account, reachable from http too with a subdomain.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 07, 2009, 01:02:04 PM
so brad like i told u i couldn;t get rausb0 up from net.config, seems for some reason my net config (same file i use for ext3) is not executed (at least for rausb0, my 2nd net interface after eth0), when i moved all required lines to S20wireless:

insmod $APATH/lib/modules/2.6.15-TvDock/rt73.ko
ifconfig rausb0 up
[ -e $AROOT/wpa-supplicant.conf ] && cp $AROOT/wpa-supplicant.conf /tmp
wpa_supplicant -Bw -Dralink -irausb0 -c/tmp/wpa-supplicant.conf
udhcpc -H wdtv -i rausb0 &

i've got wpa running on boot without probs.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 07, 2009, 01:41:00 PM

http://b-rad.cc/log-saver.app.bin


Thank you for these packages, please note that those download locations are not linked from your site, i searched deeply wireless-mod before finding it here.

Thank you and keep up the good work!

P.S If you want i can offer you (and the wdtv community) an ftp drop box or full account, reachable from http too with a subdomain.

If you're talking about the wireless-mod-wdlxtv package, yes its not available on my site because I don't want to get 1000000 emails asking why it doesnt work (yet)

log-saver is more a debug package I whipped up but I will release it to the public as well.

I'll think about the ftp offer & get back to you, only problem there is I'd like full statistics of what is being downloaded for record keeping.
Title: Re: *experimental* wireless usb support package
Post by: deffie on April 08, 2009, 04:29:04 AM
I'll think about the ftp offer & get back to you, only problem there is I'd like full statistics of what is being downloaded for record keeping.

Hi b-rad, please check your pm
Title: Re: *experimental* wireless usb support package
Post by: bradel on April 08, 2009, 07:20:18 PM
I'm trying (with no success) to use the usb wireless WL-113 from Sitecom with the chipset ZD1211U. The essid is 0df6:9071. It's because the chipset is not supported?

Using in net.config:

ifconfig $MDEV up
iwconfig $MDEV 0df6:9071 OutSideWorld




Thanks in advance.
Title: Re: *experimental* wireless usb support package
Post by: peterskeetero on April 10, 2009, 08:34:31 PM
Hi all,
I'm using ext3-0.9 with a DWA-110...using filezilla or command line I'm getting about 490K sec... Took over 10 mins
to upload a 24 episode (350mb) to wdtv...that seems pretty slow to me on any wireless network ?? Usually laptop file transfers
are very quick...log follows...
Also, if I upload a video, i need to more or less restart the wdtv to see the file ...this is really annoying - is there anything in the pipeline
that could be done to fix this...seems quite silly that a refresh of the file system isnt being done already...
My 20 cents ..otherwise the wdtv and hacked firmware is great ! Thankyou to all..
Peter
---------------------------------------------------------------------------------------------------------------------------------------
Jan  1 00:00:20 wdtv syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:20 wdtv user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:20 wdtv user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #2 PREEMPT Mon Sep 15 20:20:41 CST 2008
Jan  1 00:00:20 wdtv user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:20 wdtv user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:20 wdtv user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:20 wdtv user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:20 wdtv user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:20 wdtv user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:20 wdtv user.warn kernel: Determined physical RAM map:
Jan  1 00:00:20 wdtv user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:20 wdtv user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:20 wdtv user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:20 wdtv user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:20 wdtv user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:20 wdtv user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:20 wdtv user.warn kernel: Built 1 zonelists
Jan  1 00:00:20 wdtv user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:20 wdtv user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:20 wdtv user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:20 wdtv user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:20 wdtv user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:20 wdtv user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:20 wdtv user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:20 wdtv user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:20 wdtv user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:20 wdtv user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:20 wdtv user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:20 wdtv user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:20 wdtv user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:20 wdtv user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:20 wdtv user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:20 wdtv user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:20 wdtv user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:20 wdtv user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:20 wdtv user.notice root: Displaying detected USB devices...
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:20 wdtv user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:20 wdtv user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:20 wdtv user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:20 wdtv user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:20 wdtv user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:20 wdtv user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:20 wdtv user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:20 wdtv user.info kernel: Initializing Cryptographic API
Jan  1 00:00:20 wdtv user.info kernel: io scheduler noop registered
Jan  1 00:00:20 wdtv user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:20 wdtv user.info kernel: io scheduler deadline registered
Jan  1 00:00:20 wdtv user.info kernel: io scheduler cfq registered
Jan  1 00:00:20 wdtv user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:21 wdtv user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:21 wdtv user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:21 wdtv user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:21 wdtv user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:21 wdtv user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:21 wdtv user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:21 wdtv user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:21 wdtv user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:21 wdtv user.notice root:  [0457:0151] 1-1( 2.00,480m) USB Mass Storage Device/d232b15488571d
Jan  1 00:00:21 wdtv user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:21 wdtv user.notice kernel: number of CFI chips: 1
Jan  1 00:00:21 wdtv user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:21 wdtv user.notice kernel: Using physmap partition definition
Jan  1 00:00:21 wdtv user.notice kernel: Adding partition #1-#5
Jan  1 00:00:21 wdtv user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:21 wdtv user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:21 wdtv user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:21 wdtv user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:21 wdtv user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:21 wdtv user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:21 wdtv user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:21 wdtv user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:21 wdtv user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:21 wdtv user.warn kernel: TangoX USB initializing...
Jan  1 00:00:21 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:21 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:21 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:21 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:21 wdtv user.info kernel: hub 1-0:1.0: USB hub foun
Jan  1 00:00:21 wdtv user.info kernel: d
Jan  1 00:00:21 wdtv user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:21 wdtv user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:21 wdtv user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:21 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:21 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:21 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:21 wdtv user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:21 wdtv user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:21 wdtv user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:21 wdtv user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:21 wdtv user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:21 wdtv user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:21 wdtv user.debug kernel: usb-storage: device found at 2
Jan  1 00:00:21 wdtv user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:21 wdtv user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:21 wdtv user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:21 wdtv user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:21 wdtv user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:21 wdtv user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:21 wdtv user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:21 wdtv user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:21 wdtv user.info kernel: TCP reno registered
Jan  1 00:00:21 wdtv user.info kernel: TCP bic registered
Jan  1 00:00:21 wdtv user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:21 wdtv user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:21 wdtv user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:21 wdtv user.notice root:  [07d1:3c07] 1-2( 2.00,480m) 802.11 bg WLAN
Jan  1 00:00:21 wdtv user.notice kernel:   Vendor: USB 2.0   Model: Flash Disk        Rev: 0.00
Jan  1 00:00:21 wdtv user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
Jan  1 00:00:21 wdtv user.notice kernel: SCSI device sda: 2007040 512-byte hdwr sectors (1028 MB)
Jan  1 00:00:21 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:00:21 wdtv user.debug kernel: sda: Mode Sense: 00 00 00 00
Jan  1 00:00:21 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:21 wdtv user.notice kernel: SCSI device sda: 2007040 512-byte hdwr sectors (1028 MB)
Jan  1 00:00:21 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:00:21 wdtv user.debug kernel: sda: Mode Sense: 00 00 00 00
Jan  1 00:00:21 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:21 wdtv user.info kernel:  sda: sda1
Jan  1 00:00:21 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:21 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:21 wdtv user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:21 wdtv user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:00:21 wdtv user.info kernel: EXT3 FS on loop1, internal journal
Jan  1 00:00:21 wdtv user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:00:21 wdtv user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:00:21 wdtv user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:00:21 wdtv user.warn kernel: em8xxx: no version for "llad_open" found: kernel tainted.
Jan  1 00:00:21 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/1_01_21/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:00:21 wdtv user.warn kernel: em8xxx0 [/home/andy/WDTV/1_01_21/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:00:21 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/1_01_21/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:00:21 wdtv user.warn kernel: mumk_register_tasklet: (0) tasklet c401e000 status @c938aa24
Jan  1 00:00:21 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/1_01_21/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:00:22 wdtv user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:22 wdtv user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:22 wdtv daemon.info utelnetd[544]: utelnetd (port: 23, ifname: any, login: /bin/sh) startup succeeded
Jan  1 00:00:22 wdtv user.notice root: INIT: mounting app binaries...
Jan  1 00:00:23 wdtv user.notice root: Mounting /boot/wireless-mod.app.bin at /apps/wireless-mod
Jan  1 00:00:24 wdtv user.notice root: Path set to /apps/wireless-mod/bin:/boot/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:25 wdtv authpriv.info dropbear[649]: Running in background
Jan  1 00:00:25 wdtv user.notice root: vfat: Waiting for 5087-20C6 to mount
Jan  1 00:00:25 wdtv user.notice root: Polling detected drives...
Jan  1 00:00:26 wdtv user.notice root: Waiting for /dev/sda1 to come online (UUID=5087-20C6)...
Jan  1 00:00:31 wdtv user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:31 wdtv user.info kernel: Loading wireless extentions module...
Jan  1 00:00:31 wdtv user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:33 wdtv user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:33 wdtv user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:33 wdtv user.info kernel: usbcore: registered new driver asix
Jan  1 00:00:33 wdtv user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:00:33 wdtv user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:00:33 wdtv user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:00:34 wdtv user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver catc
Jan  1 00:00:34 wdtv user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:00:34 wdtv user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:00:34 wdtv user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:34 wdtv user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:00:35 wdtv user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:00:35 wdtv user.info kernel: usbcore: registered new driver net1080
Jan  1 00:00:35 wdtv user.info kernel: usbcore: registered new driver plusb
Jan  1 00:00:35 wdtv user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:00:36 wdtv user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:00:36 wdtv user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:37 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:00:37 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:00:37 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:38 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:38 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:38 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:38 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:39 wdtv user.warn kernel: idVendor = 0x7d1, idProduct = 0x3c07
Jan  1 00:00:39 wdtv user.notice root: net.agent: Called for rausb0
Jan  1 00:00:40 wdtv user.warn kernel: => usb_rtusb_open
Jan  1 00:00:40 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:45 wdtv daemon.notice statd[1235]: Version 1.1.5 Starting
Jan  1 00:00:45 wdtv daemon.notice statd[1235]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:00:48 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:48 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:50 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:00:50 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:00:55 wdtv user.warn kernel: MlmeAssocReqAction(): WPA2/WPA2PSK fill the ReqVarIEs with CipherTmp!
------------------------------------------------------------------------------------------------------------------------------------
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 10, 2009, 11:22:47 PM
Any idea why my wlan drop the connection after liek 10 min?
I must then repower the unit.
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 11, 2009, 04:33:11 PM
I have a Belkin N+ Router and got myself a TL-WN821N Wlan Stick (Atheros Otus supported) and am ready to test. Need help in configuring. Installed WDLXTV 0.4.3.2. What next?
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 11, 2009, 10:05:05 PM
Problem with my wlan on hub.
I have a flash disk and a hdisk connected to the wdtv through a hub, if I connect my wlan stick to any other place than one of the USB port on the wdtv it do not work.
I am just woundering why this is, since my disk are found on th ehub and works just fine, hm?
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 12, 2009, 02:19:48 AM
I have a Belkin N+ Router and got myself a TL-WN821N Wlan Stick (Atheros Otus supported) and am ready to test. Need help in configuring. Installed WDLXTV 0.4.3.2. What next?


Is wireless on WDLXTV stable yet? I'd say try Zorander's ext3-boot release first. Maybe not yet available for fw 1.02.03 but I got it running out of the box with a zd1211b wlan stick. Let us know your findings on this Otus device. Good luck.
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 12, 2009, 02:37:27 AM
the only prob i had with wdlxtv was with wpa, net.config wasn;t called for wifi device for some reason so i moved all to S20wireless and got it up and running. btw: brad if u still want to check it let me know - i will put wdtvlx back in and give u shell access.
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 12, 2009, 08:38:21 AM
First attempt using ext3-boot 0.9 and wifi for atheros otus did not work for me. What possibilities do I have to telnet to my WDTV to check output? I do not have a usb to ethernet connection. Is USB-WDTV to USB-PC Telnet possible?
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 12, 2009, 08:51:35 AM
check messages.txt
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 12, 2009, 09:33:22 AM
check messages.txt

you can check messages.txt without lan connection cause messages.txt is saved on the memory stick where u got ext-boot. After bootup close down again, move the memstick to pc and open messages.txt.
Title: Re: *experimental* wireless usb support package
Post by: needz on April 12, 2009, 09:39:50 AM
B-rad,

It seems that the D-Link DWA-110 wifi doesn't work with the latest WDXLTV 0.4.3.2 (with wireless-mod-wdlxtv.app.bin), but it does work with ext3 0.9 firmware (with wireless-mod.app.bin 0.0.3). I am putting your wdlxtv bin file in the root with the rest of the files but after restart the wlan adapter doesn't switch on (light doesn't go on). Is it possible to somehow check the differences between these 2 bin files, and change it accordingly? I tried substituting your bin with the ext3 bin (0.0.3) and renaming it to wdlxtv, but there was another problem: the adapter went on, but it couldn't connect to the AP.

Thanks!
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 12, 2009, 10:18:43 AM
I tested the first Wlan module form Brad and I tried a lot and I could not make it work.
I also asked him for a few days ago if it worked adn then he confirmed that there was some issue still..
I know he is away now so I guess we will here from he soon..

But I have anoter problem adn that is that the wlan stop workign after 10-15 minutes it looses the AP and then just blink like every 5 sec ..

Any idea?
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 13, 2009, 12:41:46 AM
Second wifi try still fail. Is it possible that the vid/pid is not listed inthe wireless_mod package (mine is 0cf3:1002)? Where can I find a list of supported vid/pid for wdtv, tried http://root.unknown.sk but no access possible.
Title: Re: *experimental* wireless usb support package
Post by: Jackman on April 13, 2009, 08:53:50 AM
Hi can you post your whole netconfig file here. I have a feeling that there is soemthing wrong in the file.. please all add what chipset your wlan dongle uses. :D
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 13, 2009, 11:12:30 AM
Wlan Dongle: TP-LINK TL-WN821N Chipset AR9001U-2NG
Should be Atheros Otus according to http://wireless.kernel.org/en/users/Drivers/otus

net.config:
Quote
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

ifconfig $MDEV up
wpa_supplicant -Bw -Dotus -i$MDEV -c/boot/wpa_supplicant.conf

wpa_supplicant.conf:
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="myssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="mypass"
}

messages.txt:
Quote
Jan  1 00:00:20 wdtv syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:20 wdtv user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:20 wdtv user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:20 wdtv user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:20 wdtv user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:20 wdtv user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:20 wdtv user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:20 wdtv user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:20 wdtv user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:20 wdtv user.warn kernel: Determined physical RAM map:
Jan  1 00:00:20 wdtv user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:20 wdtv user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:20 wdtv user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:20 wdtv user.notice root: Displaying detected USB devices...
Jan  1 00:00:20 wdtv user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:21 wdtv user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:21 wdtv user.notice root:  [0cf3:1002] 1-1( 2.00,480m) USB2.0 WLAN/12345
Jan  1 00:00:21 wdtv user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:21 wdtv user.warn kernel: Built 1 zonelists
Jan  1 00:00:21 wdtv user.notice root:  [0951:1603] 1-2( 2.00,480m) DataTraveler 2.0/0010000000000000000001BC
Jan  1 00:00:21 wdtv user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:21 wdtv user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:21 wdtv user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:22 wdtv user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:22 wdtv user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:22 wdtv user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:22 wdtv user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:22 wdtv user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:22 wdtv user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:22 wdtv user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:22 wdtv user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:22 wdtv user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:22 wdtv daemon.info utelnetd[546]: utelnetd (port: 23, ifname: any, login: /bin/sh) startup succeeded
Jan  1 00:00:22 wdtv user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:23 wdtv user.notice root: INIT: mounting app binaries...
Jan  1 00:00:23 wdtv user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:23 wdtv user.notice root: Mounting /boot/wireless-mod.app.bin at /apps/wireless-mod
Jan  1 00:00:23 wdtv user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:23 wdtv user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:24 wdtv user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:24 wdtv user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:24 wdtv user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:24 wdtv user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:24 wdtv user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:24 wdtv user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:24 wdtv user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:25 wdtv user.notice root: Path set to /apps/wireless-mod/bin:/boot/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:25 wdtv user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:26 wdtv authpriv.info dropbear[653]: Running in background
Jan  1 00:00:27 wdtv user.notice root: vfat: Waiting for 49D7-CE02 to mount
Jan  1 00:00:27 wdtv user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:27 wdtv user.notice root: Polling detected drives...
Jan  1 00:00:27 wdtv user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:28 wdtv user.notice root: Waiting for /dev/sda1 to come online (UUID=49D7-CE02)...
Jan  1 00:00:28 wdtv user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:28 wdtv user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:28 wdtv user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:29 wdtv user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:29 wdtv user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:29 wdtv user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:29 wdtv user.info kernel: Initializing Cryptographic API
Jan  1 00:00:29 wdtv user.info kernel: io scheduler noop registered
Jan  1 00:00:29 wdtv user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:30 wdtv user.info kernel: io scheduler deadline registered
Jan  1 00:00:31 wdtv user.info kernel: io scheduler cfq registered
Jan  1 00:00:31 wdtv user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:31 wdtv user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:31 wdtv user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:31 wdtv user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:31 wdtv user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:33 wdtv user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:33 wdtv user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:33 wdtv user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:33 wdtv user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:34 wdtv user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:34 wdtv user.notice kernel: number of CFI chips: 1
Jan  1 00:00:35 wdtv user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:35 wdtv user.notice kernel: Using physmap partition definition
Jan  1 00:00:35 wdtv user.notice kernel: Adding partition #1-#5
Jan  1 00:00:36 wdtv user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:37 wdtv user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:37 wdtv user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:37 wdtv user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:38 wdtv user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:38 wdtv user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:39 wdtv user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:39 wdtv user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:39 wdtv user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:39 wdtv user.warn kernel: TangoX USB initializing...
Jan  1 00:00:40 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:40 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:40 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:40 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:41 wdtv user.info kernel: hub 1-0:1.0: USB hub fou
Jan  1 00:00:43 wdtv user.info kernel: nd
Jan  1 00:00:45 wdtv user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:45 wdtv user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:45 wdtv daemon.notice statd[1189]: Version 1.1.5 Starting
Jan  1 00:00:45 wdtv user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:45 wdtv daemon.notice statd[1189]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:00:47 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:47 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:47 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:48 wdtv user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:48 wdtv user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:49 wdtv user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:49 wdtv user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:49 wdtv user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:49 wdtv user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:49 wdtv user.debug kernel: usb-storage: device found at 3
Jan  1 00:00:50 wdtv user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:50 wdtv user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:50 wdtv user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:50 wdtv user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:50 wdtv user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:50 wdtv user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:51 wdtv user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:51 wdtv user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:51 wdtv user.info kernel: TCP reno registered
Jan  1 00:00:51 wdtv user.info kernel: TCP bic registered
Jan  1 00:00:51 wdtv user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:51 wdtv user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:51 wdtv user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:51 wdtv user.notice kernel:   Vendor: Kingston  Model: DataTraveler 2.0  Rev: 1.00
Jan  1 00:00:52 wdtv user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
Jan  1 00:00:52 wdtv user.notice kernel: SCSI device sda: 1952768 512-byte hdwr sectors (1000 MB)
Jan  1 00:00:52 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:00:52 wdtv user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:52 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:52 wdtv user.notice kernel: SCSI device sda: 1952768 512-byte hdwr sectors (1000 MB)
Jan  1 00:00:52 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:00:52 wdtv user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:53 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:53 wdtv user.info kernel:  sda: sda1
Jan  1 00:00:53 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:53 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:54 wdtv user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:54 wdtv user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:00:55 wdtv user.info kernel: EXT3 FS on loop1, internal journal
Jan  1 00:00:55 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:00:55 wdtv user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:00:55 wdtv user.notice root: Now mounted:
Jan  1 00:00:55 wdtv user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:00:56 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:00:56 wdtv user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:00:56 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:00:56 wdtv user.warn kernel: em8xxx: no version for "llad_open" found: kernel tainted.
Jan  1 00:00:56 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:00:56 wdtv user.warn kernel: em8xxx [/home/william/working/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:00:56 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:00:56 wdtv user.warn kernel: em8xxx0 [/home/william/working/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:00:56 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:00:56 wdtv user.warn kernel: em8xxx [/home/william/working/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:00:57 wdtv user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:00:57 wdtv user.warn kernel: mumk_register_tasklet: (0) tasklet c401e000 status @c938aa24
Jan  1 00:00:57 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:00:57 wdtv user.warn kernel: em8xxx [/home/william/working/house/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:00:57 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:00:57 wdtv user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:57 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:00:58 wdtv user.info kernel: Loading wireless extentions module...
Jan  1 00:00:58 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:00:58 wdtv user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:58 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:00:58 wdtv user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:58 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:00:59 wdtv user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:59 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:00:59 wdtv user.info kernel: usbcore: registered new driver asix
Jan  1 00:00:59 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:00:59 wdtv user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:00:59 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:00:59 wdtv user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:00 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB2/49D7-CE02 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:01 wdtv user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:02 wdtv user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:02 wdtv user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:02 wdtv user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:03 wdtv user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:03 wdtv user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:03 wdtv user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered
Jan  1 00:01:03 wdtv user.info kernel: new driver net1080
Jan  1 00:01:03 wdtv user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:04 wdtv user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:04 wdtv user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:04 wdtv user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:01:04 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:04 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:04 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:05 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:05 wdtv user.warn kernel: rtusb init --->
Jan  1 00:01:05 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:05 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:05 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:05 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)

Thanks for the help


Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 14, 2009, 12:35:38 AM
My messages.txt for ZD1211b
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 14, 2009, 06:31:15 AM
the only prob i had with wdlxtv was with wpa, net.config wasn;t called for wifi device for some reason so i moved all to S20wireless and got it up and running. btw: brad if u still want to check it let me know - i will put wdtvlx back in and give u shell access.

definitely. I've just been out of town a lot and very busy. PM with times that are good with you and I'll try and make one of them to get this working.
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 14, 2009, 06:38:18 AM
I've to buy a wi-fi dongle for WDTV. I found a Sitecom WL-608. This dongle should have an RT2870 chipset.
Please can you tell me if usb id 0df6:003f is present insiede 2870 module for wdtv ?
Thanks
Title: Re: *experimental* wireless usb support package
Post by: laforma on April 14, 2009, 04:29:35 PM
hi everybody and thanks for trying to improve this little black box.

here is my question: it seems, that my belkin f5d7050 uses a ralink rt73 chipset. on ralinks website is a link to the source code of the driver. perhaps is it possible to somehow merge the source with yours to implement support for the rt73 chipset.

here is the link to the drivers page: http://www.ralinktech.com/ralink/Home/Support/Linux.html

would be awesome if you can make it work, i can barely imagen how complicated the whole thing is.

greets from germany, laforma.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 15, 2009, 01:51:06 AM
rezmus has a list of supported cards with vids/pids on the polish wdtv wiki. http://pl.wiki.wdtv.org/doku.php?id=wlanusb
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 15, 2009, 03:58:47 AM
laforma: check which vid / pid has your device because it seems there are several versions.
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 15, 2009, 12:01:09 PM
I'm trying an Asus WL-167G v2 dongle with 0.8.7.2 firmware and wireless app bin 0.3, but without success.
Usb id is in rezmus list (0b05:1723).

net.config
Code: [Select]
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.1.65
#GW=192.168.1.1
#NM=255.255.255.0
#DNS1=212.216.112.222
#DNS2=212.216.172.62

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

ifconfig $MDEV up
iwconfig $MDEV essid cionci channel 11
Wireless network is based on Netgear DG834G v4 router. No WEP nor WPA.
messages.txt is attached.

I cannot access telnet or ssh because I don't have any USB to Ethernet adapter.
One led on wifi dongle is always on, the other led blinks every 10-20 seconds.
Title: Re: *experimental* wireless usb support package
Post by: eliafino on April 15, 2009, 12:17:38 PM
I'm trying an Asus WL-167G v2 dongle with 0.8.7.2 firmware and wireless app bin 0.3, but without success.
Try this:

Code: [Select]
ifconfig rausb0 up
iwconfig rausb0 essid cionci

Ciao
Title: Re: *experimental* wireless usb support package
Post by: laforma on April 15, 2009, 12:35:22 PM
hi rezmus,

the vid is 050d and the pid is 705a. perhaps these data are useful for you :)
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 15, 2009, 12:53:05 PM
eliafino: I've tried that too, with no luck.

Ciao ;)
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 15, 2009, 01:10:14 PM
Is there a way to log iwconfig and ifconfig output from net.config ?
I've tried to redirect output to a file, but it don't works:

iwconfig > /tmp/media/usb/USB1/49E6-29E0/log.txt
Title: Re: *experimental* wireless usb support package
Post by: shadow on April 15, 2009, 02:41:06 PM
 cionci,

 Have you tried with fixed IP address in net.config? (no DHCP, and set IP stuff?..)

 Sometimes my WDTV did not worked in Wifi when I use DHCP (maybe my AP is buggy :)  ),
 But when I use fixed IP it always work.

  Now it works like a charm (with fixed IP).

 Regards,
 Shadow
Title: Re: *experimental* wireless usb support package
Post by: deffie on April 15, 2009, 09:32:13 PM
Is there a way to log iwconfig and ifconfig output from net.config ?
I've tried to redirect output to a file, but it don't works:

iwconfig > /tmp/media/usb/USB1/49E6-29E0/log.txt

get http://b-rad.cc/log-saver.app.bin

mount it -o loop to a mountpoint of your choice check the init script in mountpoint/etc/init.d/
you can use it as it is or modify it to get additional informations.
it is a read only cramfs so better you copy the script into wireless-mod (which is an ext2 image) (mount it just like before and copy from first mountpoint/etc/init.d/ to second mountpoint/etc/init.d)
you will see that there is a variable to refer to the usb key root.

good hacking :)
Ciao :P

P.S Let me spend a couple of words about 'sync'; i had some problems with the log saver app and data corruption, so better you call /bin/sync whenever you write on the usb key.

Code: [Select]
dev:~# mkdir log-saver
dev:~# wget www.b-rad.cc/log-saver.app.bin
--2009-04-16 07:42:47--  http://www.b-rad.cc/log-saver.app.bin
...snip...
2009-04-16 07:42:49 (18,7 KB/s) - "log-saver.app.bin" salvato [4096/4096]

dev:~# mount -o loop log-saver.app.bin log-saver
dev:~# cat log-saver/etc/init.d/S99log-saver
#!/bin/sh

cd $AROOT
lastMESSAGES="`ls -l messages.txt* | tail -n 1 | cut -d'.' -f 3`"
[ "$lastMESSAGES" == "" ] && lastMESSAGES=-1
lastMESSAGES=`expr $lastMESSAGES + 1`

lastDMESG="`ls -l dmesg.txt* | tail -n 1 | cut -d'.' -f 3`"
[ "$lastDMESG" == "" ] && lastDMESG=-1
lastDMESG=`expr $lastDMESG + 1`

lastSYSTEM="`ls -l system.txt* | tail -n 1 | cut -d'.' -f 3`"
[ "$lastSYSTEM" == "" ] && lastSYSTEM=-1
lastSYSTEM=`expr $lastSYSTEM + 1`

{
while [ true ] ; do
        cp -f /tmp/messages.txt $AROOT/messages.txt.${lastMESSAGES}
        dmesg > $AROOT/dmesg.txt.${lastDMESG}
        echo `lsmod` ========  `lsusb` ========= `cat /proc/partitions`
 ========                                                                                                                                 `blkid` ======== `cat /etc/mtab` > $AROOT/system.txt.${lastSYSTEM}
        sleep 15
done
} &
dev:~#

then add sync before sleep 15, and add every additional log operation before the sync.
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 15, 2009, 09:56:23 PM
P.S Let me spend a couple of words about 'sync'; i had some problems with the log saver app and data corruption, so better you call /bin/sync whenever you write on the usb key.
---snip---


changed log-saver to sync now ;) and made the system output a bit prettier
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 16, 2009, 12:44:09 AM
@ Cionci:

# attempt to set jumbo frames
MTU=9000

I see you have jumbo frames enabled. Try again with jumbo frames disabled.

# MTU=9000  ;D
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 01:09:35 AM
Here is output of iwconfig for the wifi key automatically associated to the access point on my desktop linux:

Code: [Select]
wlan0     IEEE 802.11bg  ESSID:"cionci" 
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:1E:2A:1F:xx:xx  
          Bit Rate=54 Mb/s   Tx-Power=12 dBm  
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B  
          Power Management:off
          Link Quality=70/100  Signal level:-60 dBm 
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


@ dreadloos: thanks, but it's just an old net.config, sorry. Now jumbo frames is off.

@ deffie: Ok, I'll try log saver.

Are you sure wireless.app.bin is an ext2 fs ?

sudo mount -t ext2 -o loop /media/disk-1/wireless-mod.app.bin /media/ntfs

Tells me it's not an ext2 fs.
I've tried automatic mount:

sudo mount -o loop /media/disk-1/wireless-mod.app.bin /media/ntfs

and mtab shows:

/dev/loop0 /media/ntfs cramfs rw 0 0

Ok, not a big problem, it's a rw cramfs image. I'll write looger to it anyway.

Thanks a lot ;)

Edit: no success on writing to /media/ntfs/etc/init.d. It tells it's read-only file system...
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 16, 2009, 01:16:48 AM
Using a BlueNext BN-WD54G USB WLAN (rt73 chipset) with the latest ext3-boot (linked to the 1.02.04 binaries)
and wireless-mod.app.bin (not sure which version I picked up) the wlan works on my wdtv. I'm using a
Netgear DG834GT router and WPA-PSK encryption.

It picked up my UPNP server running on a Buffalo Linkstation 2 and I was able to mount a samba share
on the same machine.

I still have to do speed and NFS testing.

My net.config is

Quote
# cat net.config
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.12
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

#NTP=pool.ntp.org
ifconfig rausb0 up
wpa_supplicant -Bw -Dralink -i rausb0 -c /boot/wpa_supplicant.conf

My wpa_suplicant file is

Quote
#ctrl_interface=/tmp/wpa_supplicant
network={
ssid="my network name"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="my psk password"
}

ssh and telnet I managed to get working but I couldn't use scp for some reason.
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 01:59:31 AM
log-saver has a strange behavior, no log was created and I got errors in messages.txt:

Jan  1 00:00:24 wdtv user.notice root: Mounting /boot/log-saver.app.bin at /apps/log-saver
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=68, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=1252, limit=8
Jan  1 00:00:24 wdtv user.info kernel: attempt to access beyond end of device
Jan  1 00:00:24 wdtv user.info kernel: loop0: rw=0, want=1028, limit=8

Now I'm trying to set up wifi using WEP:
Code: [Select]
HOST=wdtv
DHCP=yes
ifconfig rausb0 up
iwconfig rausb0 essid cionci key "90817D4D03C351B611EAAAAAAA" rate 54M
Title: Re: *experimental* wireless usb support package
Post by: eliafino on April 16, 2009, 02:07:59 AM
@cionci

your USB pen is formatted FAT32 or NTFS?
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 02:08:30 AM
FAT32
There are two partition on USB hard disk: the first FAT32 (with boot images on) and the second NTFS.
Title: Re: *experimental* wireless usb support package
Post by: eliafino on April 16, 2009, 02:22:31 AM
Can you try with an USB pen?
My WDTV is connect via WIFI... if you want, I have an USB-ethernet interface, I can ship to you for experiments...
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 02:39:11 AM
I've tried my two usb pens (an old Adata 1GB and a new Sandisk Cruzer 8 GB purchased for WDTV), but modded firmware doesn't boot from any of those. A little strange.
I don't think it's an issue of partitions, because kernel seems to work fine.
Thanks for the offer, I will take it in consideration if I couldn't get wifi to work :D

Grazie ;)
Title: Re: *experimental* wireless usb support package
Post by: deffie on April 16, 2009, 02:44:54 AM
Quote
Are you sure wireless.app.bin is an ext2 fs ?

sudo mount -t ext2 -o loop /media/disk-1/wireless-mod.app.bin /media/ntfs

Tells me it's not an ext2 fs.
I've tried automatic mount:

sudo mount -o loop /media/disk-1/wireless-mod.app.bin /media/ntfs

and mtab shows:

/dev/loop0 /media/ntfs cramfs rw 0 0

Ok, not a big problem, it's a rw cramfs image. I'll write looger to it anyway.

Thanks a lot ;)

Edit: no success on writing to /media/ntfs/etc/init.d. It tells it's read-only file system...


12:37:11 [root@spawn]:~# file log-saver.app.bin
log-saver.app.bin: Linux Compressed ROM File System data, little endian size 4096 version #2 sorted_dirs CRC 0x6b2b644f, edition 0, 3 blocks, 6 files

FrankLaptop:Downloads giacomo$ file wireless-mod-wdlxtv.app.bin
wireless-mod-wdlxtv.app.bin: Linux rev 1.0 ext2 filesystem data

I suppose you are talking of zorander's wireless-mod.app.bin, I'm talking of b-rad wireless-mod-wdlxtv.app.bin, you can find it here:
http://rs661gc.rapidshare.com/files/218374138/858349/wireless-mod-wdlxtv.app.bin

The choice depends on the firmware you are using.

Ciao,
Giacomo.
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 03:07:21 AM
I talk about the one by Zorander ;)
Ok, now I'm trying to modify cramfs image to add script launching.
Please tell me if I'm right:

sudo mount -t cramfs -o loop Desktop/wireless-mod.app.bin /media/cramfs
mkdir wireless-mod
sudo cp -Rp /media/cramfs/* wireless-mod
sudo cp S99log-saver wireless-mod/etc/init.d/
sudo chmod 755 wireless-mod/etc/init.d/S99log-saver
sudo chown 1004:daemon wireless-mod/etc/init.d/S99log-saver
mkcramfs wireless-mod wireless-mod.app.bin

Wireless-mod seems to be loaded, but no logs were created.
I'll try to use real mount path instead of the environment variable the script use.
Title: Re: *experimental* wireless usb support package
Post by: shadow on April 16, 2009, 05:28:08 AM

 cionci,

 As I stated before, I had similar problems in the past (the iwconfig shown that it was connected in my wifi network, but have no acess to WDTV). I solved this by NOT USING DHCP (I think that may be some problem in my DHCP server; not in WDTV); Have you tried using static IP in your net.config?

Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 05:33:57 AM
Have you tried using static IP in your net.config?
Yes, I've tried static IP too :(
Now I'm able to log custom commands, so I'll try static IP again.
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 05:49:43 AM
I got more logs. I've added S99log-saver to Zorander wireless-mod image using previous commands.

S99log-saver:
Code: [Select]
#!/bin/sh

MYROOT=/boot

dmesg > $MYROOT/dmesg.txt
blkid > $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
lsusb >> $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
cat /proc/partitions >> $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
cat /etc/mtab >> $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
lsmod >> $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
iwconfig >> $MYROOT/system.txt
echo ====================================== >> $MYROOT/system.txt
ifconfig >> $MYROOT/system.txt
call $MYROOT/lastscript.sh
sync
sleep 15
Anyone know why did /boot/lastscript.sh not execute ?
Logs in a couple of minutes ;)
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 06:56:24 AM
No news :( iwconfig didn't report any error when I set parameters, but seems to not recognize any setting.

net.config:
Code: [Select]
HOST=wdtv

ifconfig rausb0 up
iwconfig rausb0 essid cionci key "AAAAAAAAAAAAAAAAAAAAAAAAA" rate 54M channel 11 mode Managed > /boot/log.txt &2>1
sleep 2
iwconfig >> /boot/log.txt
echo "--------------------" >> /boot/log.txt
ifconfig -a >> /boot/log.txt

# DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.65
GW=192.168.1.1
NM=255.255.255.0
DNS1=212.216.112.222
DNS2=212.216.172.62
/boot/log.txt:
Code: [Select]
rausb0    RT73 WLAN  ESSID:off/any
          Mode:Auto  Frequency=2.412 GHz  Bit Rate=54 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=0/100  Signal level:-121 dBm  Noise level:-115 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

--------------------
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

rausb0    Link encap:Ethernet  HWaddr 00:24:8C:26:60:A7 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:66 (66.0 B)

Now I'll try to get output of iwlist command...
Title: Re: *experimental* wireless usb support package
Post by: deffie on April 16, 2009, 07:21:15 AM
I talk about the one by Zorander ;)
Ok, now I'm trying to modify cramfs image to add script launching.
Please tell me if I'm right:

sudo mount -t cramfs -o loop Desktop/wireless-mod.app.bin /media/cramfs
mkdir wireless-mod
sudo cp -Rp /media/cramfs/* wireless-mod
sudo cp S99log-saver wireless-mod/etc/init.d/
sudo chmod 755 wireless-mod/etc/init.d/S99log-saver
sudo chown 1004:daemon wireless-mod/etc/init.d/S99log-saver
mkcramfs wireless-mod wireless-mod.app.bin

Wireless-mod seems to be loaded, but no logs were created.
I'll try to use real mount path instead of the environment variable the script use.

I suggest you to move to an ext2 image which can do rw (cramfs cannot).

ie. to make a 32mb ext2 image:
dd if=/dev/zero of=fsimage.bin bs=1024 count=32k
mkfs -t ext2 -i 1024 -b 1024 -F fsimage.bin

Variables for zorander's ext3 are:
$AROOT = path where the .bin file is sitting
$APATH = path where the .bin filesystem is mounted

Please note that log-saver is for b-rad images, zorander image doesnt have some of the apps you would use to get debug informations.

About your iwconfig, theres something strange in your signal/noise level, I had a similar issue porting an rt2x00 based card to rt73 driver.
Title: Re: *experimental* wireless usb support package
Post by: draadloos on April 16, 2009, 07:27:25 AM
 :) Anybody got a hispeed (N-draft) wlan adapter with atheros otus working yet?
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 16, 2009, 07:42:58 AM
I suggest you to move to an ext2 image which can do rw (cramfs cannot).

Please note that log-saver is for b-rad images, zorander image doesnt have some of the apps you would use to get debug informations.
Now it works. I've reduced the original script to a simpler one. I think I don't need to write to cramfs again.
About your iwconfig, theres something strange in your signal/noise level, I had a similar issue porting an rt2x00 based card to rt73 driver.
What's the cause ? It's similar to mine maybe... Modules on my desktop Ubuntu:
Code: [Select]
rt73usb                32768  0
crc_itu_t              10496  1 rt73usb
rt2x00usb              20480  1 rt73usb
rt2x00lib              40576  2 rt73usb,rt2x00usb
rfkill                 19364  1 rt2x00lib
led_class              13192  1 rt2x00lib
mac80211              253312  2 rt2x00usb,rt2x00lib
cfg80211               37136  2 rt2x00lib,mac80211
usbcore               175760  10 rt73usb,rt2x00usb,usb_storage,libusual,usbhid,ehci_hcd,uhci_hcd

Modules in wdtv:
Code: [Select]
rt73                  289040  1
rt2870sta             522448  0
wireless_ext            8240  5 rt73,rt2870sta,arusb_lnx,zd1211b,zd1201

An extended lsusb:
Code: [Select]
Bus 003 Device 023: ID 0b05:1723 ASUSTek Computer, Inc. WL-167G v2 802.11g Adapter [ralink]
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0b05 ASUSTek Computer, Inc.
  idProduct          0x1723 WL-167G v2 802.11g Adapter [ralink]
  bcdDevice            0.01
  iManufacturer           1 Ralink
  iProduct                2 802.11 bg WLAN
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              300mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)
I can't get iwlist output, I think it's blank, I'll try redirecting stderr too.
Is iwllist command line the same as on desktop ?
Title: Re: *experimental* wireless usb support package
Post by: eliafino on April 16, 2009, 10:50:53 AM
iwlist rausb0 scanning

Code: [Select]
rausb0    Scan completed :
          Cell 01 - Address: 00:18:84:1F:7B:BD
                    Mode:Managed
                    ESSID:"eliafino"
                    Channel:5
                    Encryption key:on
                    Bit Rates:2 Mb/s
          Cell 02 - Address: 00:18:84:27:8E:25
                    Mode:Managed
                    ESSID:"Aladino"
                    Channel:11
                    Encryption key:on
                    Bit Rates:3 Mb/s

iwlist rausb0 peers

Code: [Select]
rausb0    Peers/Access-Points in range:
    00:18:84:1F:7B:BD : Quality:83/100  Signal level:-56 dBm  Noise level:-79 dBm
    00:18:84:27:8E:25 : Quality:75/100  Signal level:-64 dBm  Noise level:-79 dBm
Title: Re: *experimental* wireless usb support package
Post by: FooFighter on April 17, 2009, 07:34:41 AM
Linksys WUSB600N + WDLXTV 0.4.4 + wireless-mod-wdlxtv.app.bin

I have a linksys wusb600n stick with a rt2870 draft chipset.

lsusb output is fine:
[1737:0071] 1-2.4( 2.00,480m) Dual-Band Wireless-N USB Network Adapter

modprobe rt2870sta works fine
dmesg:
rtusb init --->
usbcore: registered new driver rt2870

but no network device is found so I suppose the id might be missing. the ralink drivers v2.1.0.0 from
http://www.ralinktech.com/ralink/Home/Support/Linux.html (http://www.ralinktech.com/ralink/Home/Support/Linux.html)
have the id of this device registered in the os/linux/usb_main_dev.c. former releases had to be edited here manually.

which version is used in wireless-mod-wdlxtv.app.bin?

Regards,

Foo
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 17, 2009, 08:06:52 AM
I've found why it didn't work. Router/AP was too far from WDTV :o But it's strange...I've tested signal power using the same dongle on a Windows laptop in the same place where WDTV was and signal quality was between 65 and 75%, I think there was enough signal power to associate at least.
AP and WDTV were only 7-8 meters far  ???

I've tested two USB dongle:

0b05:1723 Asus WL-167G v2 802.11g Adapter [ralink]
07d1:3c03 D-Link System DWL-G122 802.11g Adapter [ralink rt73] (it's a DWL-G122 rev. C1)

and both work.

I did some speed test mounting a Samba share:
Asus cat to /dev/null at 1.3 MB/s
D-Link cat to /dev/null at 1.2 MB/s

I did some http test too using wget and sending output to /dev/null (Apache server was my Ubuntu PC):
Asus 2.2 MB/s
D-Link 2.05 MB/s

I've a problem testing NFS share. I configured NFS server (kernel mode) on my Ubuntu PC.
Configured /etc/export like this:
/media/deposito 192.168.1.1/24(rw,no_root_squash,async)

Then mounted on WDTV:

xmount 192.168.1.64:/media/deposito test nfs
time cat /media/test/video.avi > /dev/null

Works fine if video.avi is small (about 3 MB).
WDTV hangs if video.avi is bigger (190 MB) and needs to be restated. Could be some NFS option in /etc/exports ?

Thanks
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 17, 2009, 08:51:30 AM
This is a USB hub fault !!! Sorry...


WDTV hangs (or maybe it's wireless module) during FTP transfer also.
Edit: it's wireless module because WDTV is still responding to remote controller.

Connected to 192.168.1.65.
220---------- Welcome to Pure-FTPd ----------
220-You are user number 4 of 50 allowed.
220-Local time is now 16:46. Server port: 21.
220 You will be disconnected after 15 minutes of inactivity.
Name (192.168.1.65:cionci): root
331 User root OK. Password required
Password:
230 OK. Current directory is /
Remote system type is UNIX.
Using binary mode to transfer files.
ftp> cd /boot
250 OK. Current directory is /boot
ftp> get opt.bin
local: opt.bin remote: opt.bin
200 PORT command successful
150-Connecting to port 50056
150 131072.0 kbytes to download
^C

Edit: messge.txt logging of the above issue:

Apr 17 16:47:10 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:11 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:13 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:14 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:14 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:14 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:16 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:17 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:19 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:20 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:22 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:23 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:25 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:26 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:28 wdtv user.info kernel: usb 1-2.2: reset high speed USB device using tangox-ehci-hcd and address 3
Apr 17 16:47:28 wdtv user.err kernel: hub 1-2:1.0: over-current change on port 3
Apr 17 16:47:28 wdtv user.info kernel: usb 1-2.3: USB disconnect, address 4
Apr 17 16:47:28 wdtv user.warn kernel: rausb0: unable to Mlme thread, pid=1034
Apr 17 16:47:29 wdtv user.warn kernel: fRTMP_ADAPTER_NIC_NOT_EXIST
Apr 17 16:47:30 wdtv user.warn kernel: unregister_netdev()
Apr 17 16:47:30 wdtv user.info kernel: usb 1-2.3: new high speed USB device using tangox-ehci-hcd and address 5
Apr 17 16:47:31 wdtv user.warn kernel: idVendor = 0xb05, idProduct = 0x1723

It's strange because 1-2.2 is hard disk and 1-2.3 is wlan adapter. Hub is external powered. I'll try without usb hub.
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 17, 2009, 09:11:32 AM
so, no success with D-LINK DWA 140  :'(
Title: Re: *experimental* wireless usb support package
Post by: Fredouye on April 17, 2009, 09:44:12 AM
I previously had a lot of timeouts during FTP, but since WDLXTV 0.4.3 I haven't had a single one...
Title: Re: *experimental* wireless usb support package
Post by: chris78 on April 18, 2009, 06:49:47 AM
Hi,

I got my WD Player for 3 days and installed WDLXTV-0.4.4 when I found that firmware.
At the beginning I had some problems (.bin files were not recognized...) but now thats working so far.

The only problem is that my WLan USB stick is not being found on startup of the media player.

It works with the wireless package when I do all steps manually:
in that case the interface is up and receives an IP address via DHCP from my router...

But how to do that on startup? I mean is there a prefered way to do that or will there be an update that does it automatically - as far as I understood that should already work out of the box!?

Maybe somebody has an idea?
Sorry if there is something unclear or misspelled, but I'm no native speaker...

Cheers
Chris
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 18, 2009, 08:11:05 AM
Have you tried wireless-mod-wdlxtv.app.bin ?
http://rs661gc.rapidshare.com/files/218374138/858349/wireless-mod-wdlxtv.app.bin
Title: Re: *experimental* wireless usb support package
Post by: chris78 on April 18, 2009, 09:10:37 AM
yes, I used "wireless-mod-wdlxtv.app.bin".
The message.txt says that its loaded/mounted but linux doesn't load the modules...

Chris
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 19, 2009, 10:28:22 AM
cionci, can you post net.config and wpa_supplicant.conf ? a have the same wifi usb adapter (DWL-G122) but i can connect to the router :(

thanks in advance
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 19, 2009, 03:58:02 PM
At least for me, it didn't works with DHCP, so I've to use static configuration:

Code: [Select]
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
# MTU=9000

#
# Dynamic IP Configuration:

# DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf


#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.65
GW=192.168.1.1
NM=255.255.255.0
DNS1=212.216.112.222
DNS2=212.216.172.62

#
# Optional:  specify time server host:

#NTP=pool.ntp.org
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your ssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="your key"
}

Pay attention to revision of DWL-G122: this configuration worls only on rev. C1 !!! Every revision has a different kind of chipset.
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 20, 2009, 04:12:50 AM
At least for me, it didn't works with DHCP, so I've to use static configuration:

Code: [Select]
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
# MTU=9000

#
# Dynamic IP Configuration:

# DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf


#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.65
GW=192.168.1.1
NM=255.255.255.0
DNS1=212.216.112.222
DNS2=212.216.172.62

#
# Optional:  specify time server host:

#NTP=pool.ntp.org
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your ssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="your key"
}

Pay attention to revision of DWL-G122: this configuration worls only on rev. C1 !!! Every revision has a different kind of chipset.


my wifi dongle (DWL-G122) is C1 ver and this not work for me :(

wish ext3 version hare you using
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 20, 2009, 04:16:25 AM
0.8.7.2 and Wireless-mod 0.0.3: http://www.mediafire.com/?dz1nmqloazm
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 20, 2009, 05:31:03 AM
0.8.7.2 and Wireless-mod 0.0.3: http://www.mediafire.com/?dz1nmqloazm

OK, now wifi is working version (ext3 0.8.7.2)+(wireless-mod 0.3).

newer version don't work, very strange !?

EDIT: i copy root.bin from '1.02.06-ext3-boot.0.9.1' and until now it's ok
EDIT2: problem is that i connect my wd usb disc and the wifi dongle as not enough power to run 
Title: Re: *experimental* wireless usb support package
Post by: smartP on April 21, 2009, 05:08:18 AM
For anyone with a WLAN using rt2870, REJOICE!!

I've just managed to get it all working on my WDTV and it's fricking AWESOME!

OK to get it to work....

1. Download the following package: wireless-mod-wdlxtv.app.bin-rt2870.zip (http://www.mediafire.com/download.php?ylmw2tzmiyn (http://www.mediafire.com/download.php?ylmw2tzmiyn))
Hope b-rad doesn't mind me updating his file.   :-\

2. Unzip to the root of your usb with existing WDLXTV-0.4.X files. You should have 2 new files, wireless-mod-wdlxtv.app.bin and RT2870STA.dat

3. Edit the RTA2870STA.dat with your wireless config, using README_STA as a reference. (http://www.mediafire.com/download.php?y4ty3qzqxjz (http://www.mediafire.com/download.php?y4ty3qzqxjz))

4. Edit net.config and add the following lines at the bottom:

[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
ifconfig rausb0 ra0 up
udhcpc -H wdtv -i rausb0 ra0


[updated device name to ra0 instead of rausb0]

5. Done. Reboot!!!

btw: driver version is 2.1.0.0
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 21, 2009, 06:09:40 AM
My wifi dongle fails to get IP from DHCP if I set DHCP=yes in net.config, but gets IP from DHCP if I set DHCP=no.
Do we need to delay IP settings ? Many people wrote here that their dongle work only with static IP.

Look at this:

Jan  1 00:00:49 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:49 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:50 wdtv user.warn kernel: idVendor = 0xb05, idProduct = 0x1723
Jan  1 00:00:50 wdtv user.notice root: net.agent: Called for rausb0
Jan  1 00:00:50 wdtv user.info kernel: usbcore: registered new driver rt73
[...]
Jan  1 00:00:52 wdtv user.warn kernel: => usb_rtusb_open
Jan  1 00:00:52 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.1.65 GW=192.168.1.1
Jan  1 00:00:53 wdtv user.notice root: Testing static IP assignment...
[...]
Jan  1 00:01:08 wdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:08 wdtv user.notice root: IP Assignment failed. Trying DHCP

Jan  1 00:01:11 wdtv user.notice root: net.agent: Using 2.it.pool.ntp.org to set system time
Apr 21 11:24:24 wdtv user.notice root: Device rausb0 configged as 192.168.1.65/192.168.1.1/255.255.255.0

This is a blocking bug for users who don't have a dhcp server on their network.

Boot log after I add sleep 5 at the end of net.config:

Jan  1 00:01:18 wdtv user.notice root: Ping: 6 packets transmitted, 6 packets received, 0% packet loss

With sleep 5 at the end of net.config, if I set DHCP=yes WDTV now gets IP from DHCP server too !!!
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 21, 2009, 07:12:04 AM
my config is powered hd with 2GiB FAT and 450GiB ext2 format connect to usb1, wifi DWL-G122 to usb2. wifi dont work
but if i disconnect hd and put usb pen then its run ok

 ??? :( :'(
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 21, 2009, 07:32:03 AM
Post messages.txt after you have booted with the hard disk
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 21, 2009, 07:51:54 AM
Post messages.txt after you have booted with the hard disk


there is it and thank for help
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 22, 2009, 06:16:41 AM
I've noticed I'm getting a large number of dropped packets when I use my wireless connection. When I type
"ifconfig rausb0" I get

Quote
rausb0    Link encap:Ethernet  HWaddr 00:23:CD:B9:B6:AB 
          inet addr:192.168.0.12  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:575959 errors:0 dropped:150911 overruns:150911 frame:150911
          TX packets:125038 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:631834989 (602.5 MiB)  TX bytes:16772476 (15.9 MiB)

It's not my wireless network because I've tested it using my laptop and I don't get a single dropped packet or overrun. Is this a know
problem with the WDTV with wireless USB or do I have poor USB stick?
Title: Re: *experimental* wireless usb support package
Post by: altkg on April 22, 2009, 11:10:01 AM
Help
I have the device
Device properties
Description of Conceptronic 54Mbps USB adapter # 2
Device ID 14B2-3C22
Device class FF / FF
FF Device Protocol
Manufacturer Ralink
802.11 bg WLAN product
Supported USB Version 2.00  


I have made many tests and is not connected to the network

Use
wireless-mod.app.bin 0.0.3 in VERSION='1.02.06-ext3-boot.0.9.1'
net.config
HOST=wdtv
ifconfig $MDEV up
iwconfig $MDEV essid my_land key "s:my pass"[/
size]

or
ifconfig rausb0 up
iwconfig rausb0 essid my_land key "s:my pass"[/
size]

also
ifconfig rausb0 up
 iwconfig rausb0 essid my_land  key "my pass HEX"

DHCP=no
  IP=192.168.1.41
  GW=192.168.1.1
  NM=255.255.255.0
  DNS1=80.58.81.254
  DNS2=80.58.81.250

also
DHCP=yes
also WPA-PSK

recognizes the device and not connected

messages.txt

....

Jan  1 00:00:39 wdtv user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:40 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:00:40 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:00:40 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:41 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:41 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:41 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:41 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:41 wdtv user.warn kernel: idVendor = 0x14b2, idProduct = 0x3c22
Jan  1 00:00:41 wdtv user.notice root: net.agent: Called for rausb0
Jan  1 00:00:42 oppowdtv user.warn kernel: => usb_rtusb_open
Jan  1 00:00:42 oppowdtv user.debug kernel: rausb0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
Jan  1 00:00:42 oppowdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.1.41 GW=192.168.1.1
Jan  1 00:00:43 oppowdtv user.notice root: Testing static IP assignment...
Jan  1 00:00:43 oppowdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:48 oppowdtv daemon.notice statd[1241]: Version 1.1.5 Starting
Jan  1 00:00:48 oppowdtv daemon.notice statd[1241]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:00:52 oppowdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:00:52 oppowdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:00:58 oppowdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:00:58 oppowdtv user.notice root: IP Assignment failed. Trying DHCP

I would appreciate if you can help
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 22, 2009, 10:42:22 PM
Try this:

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf
sleep 5


In wpasupplicant.conf:

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your ssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="your pass"
}
Title: Re: *experimental* wireless usb support package
Post by: altkg on April 23, 2009, 11:15:50 AM
Thank you very much, cionci, for the help, I managed to make it work
Title: Re: *experimental* wireless usb support package
Post by: dencamp on April 24, 2009, 07:55:19 AM
Hi all,
thanks to Zorander adding vid/pid of my 802.11n stick to wireless-mod I now have wireless up and running with otus  :). I still need to do some speed tests. I have a Belkin N+ router and my wlan stick is TP-Link wn821n. Using NAS attached to router via gigabit ethernet and NFS-mounts on my wdtv. Can anyone tell me a good way to test transfer speed.
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 24, 2009, 08:26:11 AM
i still can't use my DWA-140 802.11n Adapter
Title: Re: *experimental* wireless usb support package
Post by: losco on April 24, 2009, 03:15:50 PM
I'm not able to connect with my Linksys WUSB54GC (idVendor = 0x13b1, idProduct = 0x20)

Someone can help me?

Quote
Jan  1 00:00:51 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:51 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:52 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:52 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:52 wdtv user.warn kernel: idVendor = 0x13b1, idProduct = 0x20
Jan  1 00:00:52 wdtv user.notice root: net.agent: Called for rausb0
Jan  1 00:00:53 wdtv user.warn kernel: => usb_rtusb_open
Jan  1 00:00:53 wdtv user.debug kernel: rausb0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
Jan  1 00:00:53 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:58 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.0.55 GW=192.168.0.254
Jan  1 00:00:58 wdtv user.notice root: Testing static IP assignment...
Jan  1 00:00:59 wdtv daemon.notice statd[1297]: Version 1.1.5 Starting
Jan  1 00:00:59 wdtv daemon.notice statd[1297]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:02 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:02 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:11 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:01:11 wdtv user.notice root: Now mounted:
Jan  1 00:01:11 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:11 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:11 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:11 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:11 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:11 wdtv user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:11 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:01:11 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:11 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:01:11 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:11 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:11 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:11 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:12 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:12 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:01:12 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB2/6A18-1BE4 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:13 wdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:14 wdtv user.notice root: IP Assignment failed. Trying DHCP
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 24, 2009, 11:52:53 PM
Add

sleep 5

at the end of net.config ;)
Title: Re: *experimental* wireless usb support package
Post by: losco on April 25, 2009, 03:45:03 AM
Sorry i already tried, this my net.config:

Quote
ifconfig rausb0 up
iwconfig rausb0 essid losco-wifi
sleep 5

DHCP=no
IP=192.168.0.55
GW=192.168.0.254
NM=255.255.255.0
DNS1=192.168.0.254

 ???
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 25, 2009, 03:47:34 AM
Try using WPA-PSK.
Until now I had no success on using WDTV in WEP or open wifi networks :(
Title: Re: *experimental* wireless usb support package
Post by: losco on April 25, 2009, 04:47:39 AM
Tried with WPA-PSK:

net.config
Quote
ifconfig rausb0 up
wpa_supplicant -B -i rausb0 -c /boot/wpa_supplicant.conf

wpa_supplicant.conf
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
  ssid="losco"
  key_mgmt=WPA-PSK
  psk="my_personal_password"
}

this a log:
Quote
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:386 errors:0 dropped:0 overruns:0 frame:0
          TX packets:386 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:32337 (31.5 KiB)  TX bytes:32337 (31.5 KiB)

rausb0    Link encap:Ethernet  HWaddr 00:22:6B:9B:71:0C 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:6 errors:0 dropped:0 overruns:0 frame:0
          TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:622 (622.0 B)  TX bytes:1716 (1.6 KiB)

rausb0    RT73 WLAN  ESSID:off/any 
          Mode:Auto  Frequency=2.412 GHz  Bit Rate=54 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=0/100  Signal level:-121 dBm  Noise level:-115 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

I can't connect to my ap and i'm near it.

 ::)

Title: Re: *experimental* wireless usb support package
Post by: cionci on April 25, 2009, 05:39:31 AM
Write this in net.config:

ifconfig rausb0 up
sleep 5
iwlist rausb0 scanning > /boot/iwlist_scan.txt

Now post what's inside iwlist_scan.txt in your boot drive.
Are you using wireless-mod.app.bin below ?
http://www.mediafire.com/?sharekey=6d110a20e6fb482361d4646c62b381cb4dc2b76b122e4c495be6ba49b5870170
Title: Re: *experimental* wireless usb support package
Post by: dadme on April 25, 2009, 07:04:35 AM
I've instaled latest version ** WDLXTV-0.5.2 **,it works nice, but i can't get wireless working (edimax 7318usg rt73 chipset).
Same adapter works fine with ext3-boot release 0.9.2, with the same settings files and same wireless-mod 0.3.
It's necesary to raname wireless-mod.app.bin to something else?
that my config:
# Network configuration file
HOST=wdtv
# attempt to set jumbo frames
MTU=9000
#
DHCP=yes
#
##ifconfig rausb0 up
##wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf
##
ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf
sleep 5

and wpa_supplicant.conf:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="wl500gp"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="blablabla"
}
any advice is welcome
Title: Re: *experimental* wireless usb support package
Post by: losco on April 25, 2009, 08:01:15 AM
Write this in net.config:

ifconfig rausb0 up
sleep 5
iwlist rausb0 scanning > /boot/iwlist_scan.txt
...

rausb0    Scan completed :
          Cell 01 - Address: 00:1A:92:7E:23:8C
                    Mode:Managed
                    ESSID:"losco-wifi"
                    Channel:11
                    Encryption key:on
                    Bit Rates:2 Mb/s

Bit Rates very low...  ::)

But always:

user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss  >:(
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 25, 2009, 08:05:41 AM
Write this in net.config:

ifconfig rausb0 up
sleep 5
iwlist rausb0 scanning > /boot/iwlist_scan.txt
...

rausb0    Scan completed :
          Cell 01 - Address: 00:1A:92:7E:23:8C
                    Mode:Managed
                    ESSID:"losco-wifi"
                    Channel:11
                    Encryption key:on
                    Bit Rates:2 Mb/s

Bit Rates very low...  ::)

But always:

user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss  >:(

Are you using WPA-PSK or WPA2-PSK ?
Dongle works, so it's a matter of configuration only.

In the last wpa_supplicant.conf posted you wrote:
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
  [b]ssid="losco"[/b]
  key_mgmt=WPA-PSK
  psk="my_personal_password"
}
It's ssid="losco-wifi" myabe...so return to previous WPA_PSK configuration and make this change ;)
Title: Re: *experimental* wireless usb support package
Post by: losco on April 25, 2009, 08:32:04 AM
 ;D

Thanks! WORKED!!

user.notice root: Ping: 6 packets transmitted, 6 packets received, 0% packet loss

how can i force a higher bit rates? I share with a XP+Samba
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 25, 2009, 08:39:16 AM
;D

Thanks! WORKED!!

user.notice root: Ping: 6 packets transmitted, 6 packets received, 0% packet loss

how can i force a higher bit rates? I share with a XP+Samba

Look at:

iwconfig rausb0

That's your real rate
Title: Re: *experimental* wireless usb support package
Post by: drs on April 25, 2009, 01:54:59 PM
It's necesary to raname wireless-mod.app.bin to something else?

Try wireless-mod-wdlxtv.app.bin, someone posted a link here somewhere.

I had no luck getting an rt2870 dongle (Longshine LCS-8131N1) to work with WDLXTV (using wireless-mod-wdlxtv.app.bin). As I have no other access to the box (cable) I don't know if the dongle is working at all. :(
Title: Re: *experimental* wireless usb support package
Post by: dadme on April 26, 2009, 12:18:19 AM
Tryed now with wireless-mod-wdlxtv.app.bin, and driver isn't loading, with wireless-mod.app.bin vers 0.3 on wdlxtv 0.52 led is blinking on edimax ew-7318usg but no ip on router.... Any ideas?
Title: Re: *experimental* wireless usb support package
Post by: losco on April 26, 2009, 03:57:43 AM
 ;D Now it work... but i have a NEW big problem. It lose connection randomly  :-\

Has someone had the same experiences?
Title: Re: *experimental* wireless usb support package
Post by: avon on April 26, 2009, 08:09:33 AM
Tryed now with wireless-mod-wdlxtv.app.bin, and driver isn't loading, with wireless-mod.app.bin vers 0.3 on wdlxtv 0.52 led is blinking on edimax ew-7318usg but no ip on router.... Any ideas?

I have the same adapter (edimax ew-7318usg) and the same problem... It works fine with zorander's ext3-boot but not with wdlxtv ... maybe a "wireless-mod-wdlxtv.app.bin" problem???
Title: Re: *experimental* wireless usb support package
Post by: b-rad.cc on April 26, 2009, 08:15:23 AM
Tryed now with wireless-mod-wdlxtv.app.bin, and driver isn't loading, with wireless-mod.app.bin vers 0.3 on wdlxtv 0.52 led is blinking on edimax ew-7318usg but no ip on router.... Any ideas?

I have the same adapter (edimax ew-7318usg) and the same problem... It works fine with zorander's ext3-boot but not with wdlxtv ... maybe a "wireless-mod-wdlxtv.app.bin" problem???

Most likely :D How about one of you guys mail me your adapter, i'll get it working, and then mail it back to you? ;) I live on the edge of wilderness in an area with almost no big box stores, and the one that carries usb wireless adapters doesn't carry a single compatible one. I've already bought and returned their entire stock (of 4) trying to find one that works. ;D
Title: Re: *experimental* wireless usb support package
Post by: rezmus on April 26, 2009, 08:20:28 AM
i have this edimax and it works for me, only prob i had with wdlxtv was dhpc (had to set ip manualy or start udhcpc myself for some reason). had no time yet to check what could be the prob. also remember to insmod rt73.ko module in S20wireless or net.config ;)
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 26, 2009, 10:23:22 AM
i have this edimax and it works for me, only prob i had with wdlxtv was dhpc (had to set ip manualy or start udhcpc myself for some reason).
Add sleep 5 at the end of net.config and it should work ;) It's possible that you won't see the address in start splash screen.
Title: Re: *experimental* wireless usb support package
Post by: dadme on April 26, 2009, 10:40:28 AM
Tryed with insmod forced on net.config and static ip on edimax 7318usg and this is wireless part messages;
Jan  1 00:01:20 (none) user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:20 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:01:20 (none) user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:21 (none) user.warn kernel: idVendor = 0x148f, idProduct = 0x2573
Jan  1 00:01:21 (none) user.notice root: net.agent:  Called for rausb0
Jan  1 00:01:21 (none) user.warn kernel: => usb_rtusb_open
Jan  1 00:01:22 (none) user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:27 (none) user.notice root: Testing static IP assignment...
Jan  1 00:01:30 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:30 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:42 (none) user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:42 (none) user.notice root: IP Assignment failed.  Trying DHCP

any ideeas?
Title: Re: *experimental* wireless usb support package
Post by: avon on April 26, 2009, 12:32:29 PM
Ok, now it works!!!!

The problem was in the location of the "wpa_supplicant.conf" file.

Change this line in "net.config":
Code: [Select]
wpa_supplicant -Bw -Dralink -i$MDEV -c/tmp/mnt/sda1/wpa_supplicant.confinstead:
Code: [Select]
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
It only works with "wireless-mod.app.bin" , "wireless-mod-wdlxtv.app.bin" doesn't work for me.

Most likely :D How about one of you guys mail me your adapter, i'll get it working, and then mail it back to you? ;) I live on the edge of wilderness in an area with almost no big box stores, and the one that carries usb wireless adapters doesn't carry a single compatible one. I've already bought and returned their entire stock (of 4) trying to find one that works. ;D

Thanks for your answer, but I'm far from you... I'm in Spain... the shipment would take a lot of time... sorry!


*Sorry for my english  ;D
Title: Re: *experimental* wireless usb support package
Post by: dadme on April 26, 2009, 01:19:22 PM
avon, could you post your net.conf and wpa_supplicant.conf, please?
Title: Re: *experimental* wireless usb support package
Post by: avon on April 26, 2009, 03:16:01 PM
avon, could you post your net.conf and wpa_supplicant.conf, please?
Ok! this is my config with a "Edimax EW-7318USg" based on "rt73" chipset:

net.config
Code: [Select]
sleep 2

ifconfig $MDEV up
iwconfig $MDEV essid MyEssid

sleep 2
wpa_supplicant -Bw -Dralink -i$MDEV -c/tmp/mnt/sda1/wpa_supplicant.conf

sleep 2
HOST=wdtv
MTU=9000
DHCP=no
IP=192.168.1.11
GW=192.168.1.1
DNS1=192.168.1.1

sleep 5
*Maybe it would work with less "sleep" but now it work's perfect.

wpa_supplicant.conf (with WPA-PSK[TKIP] and hidden ssid)
Code: [Select]
#ctrl_interface=/tmp/wpa_supplicant
network={
ssid="MySsid"
#comment next line if your ap broadcast ssid
scan_ssid=1
key_mgmt=WPA-PSK
psk="MyPass"
}
Title: Re: *experimental* wireless usb support package
Post by: pcdthebum1 on April 27, 2009, 01:18:59 PM
I have been trying to get the trendnet TEW424UB working and everything I do I just cant get it to do anything. One thing I noticed is that from the WDTV Wiki it says that the vid/pid is 0ace/1211, whereas when I look at the messages.txt i see

Jan  1 00:00:34 (none) user.notice root:  [0781:5150] 1-1( 2.00,480m) Cruzer Mini/20043512730a1bd14127
Jan  1 00:00:35 (none) user.notice root:  [0bda:8189] 1-2( 2.00,480m) RTL8187B_WLAN_Adapter/00e04c000001

Has anyone use this? Or can tell me whats up?

Thanks
Title: Re: *experimental* wireless usb support package
Post by: Neo on April 28, 2009, 06:20:24 AM
i;ve managed to run wpa on wdlxtv 0.4.2, but had some probs getting it work on boot, will do some more tests in the evening. i used ac hub without probs until it got burned yesterday =) today i bought cheap passive one and it works ok with wire usb lan and 2 x pen in.

something that might help you, the init.d script has two important variables accessible:

Code: [Select]
$AROOTthis is the location on the wdtv that the app.bin itself resides, for example /tmp/media/usb/sda2  or /tmp/mnt/sda2

Code: [Select]
$APATHthis is the location the app.bin is mounted, so here it would be /apps/wireless-mod-wdlxtv/

So inside the init.d script if you add something like this:

Code: [Select]
[ -e $AROOT/wpa-supplicant.conf ] && cp $AROOT/wpa-supplicant.conf /tmp
and inside of your net.config add

Code: [Select]
wpa_supplicant -Bw -Dralink -irausb0 -c/tmp/wpa-supplicant.conf
Then things should work (or get closer to working)

I'll be exhanging my adapter tmr, and can then help you guys out if its not figured by then.




$AROOT
$APATH

they are, at boot time,  empty

how to correct this ?


 
Title: Re: *experimental* wireless usb support package
Post by: Ravage on April 28, 2009, 12:13:12 PM
I'm using the WUSB300N  and I can't seem to get the wireless card to activate when plugged into my WDTV. I'm currently using the latest build of the WDLXTV firmware but I've also used the ext-0.9.0 firmware for testing and neither activates my card.

I've installed everything into the root of my usb key, FAT32 formatted. I've followed the instructions found here: http://www.wdtvc.com/2009/04/06/how-to-config-wifi-usb-adapter-with-wd-tv/ and a few other peoples on this form.

It appears to use the Marvel Topdog chipset. Has anyone gotten a similar adapter to work?
Title: Re: *experimental* wireless usb support package
Post by: FooFighter on April 28, 2009, 12:59:40 PM
@Ravage: you need wireless-mod-wdlxtv.app.bin for wdlxtv as the wusb300n is a rt2870 based adapter. For this reason try this package http://wdtvforum.com/main/index.php?topic=59.msg2333#msg2333 (http://wdtvforum.com/main/index.php?topic=59.msg2333#msg2333)

if the device doesn't get recognized automatically you might telnet through a separate lan interface to your wdtv and enter

modprobe rt2870sta

then check with iwconfig if the adapter shows up. With the package above my wus300n shew up but wdtv refused to finish booting into the userinterface so I'm still bound to my DWL-G810 in this matter.
Title: Re: *experimental* wireless usb support package
Post by: Ravage on April 28, 2009, 01:12:41 PM
Oh I should have mentioned I have the bin file as well in my root. Thanks for identifying the adapter! I'll add that and see what happens.
Title: Re: *experimental* wireless usb support package
Post by: Ravage on April 28, 2009, 01:46:05 PM
I've followed the instructions, rebooted 3 times, nothing yet.

Foofighter since we seem to have a similar configuration would you be able to post your net.config ?
Title: Re: *experimental* wireless usb support package
Post by: FooFighter on April 28, 2009, 08:34:17 PM
try this config as it is for a ralink ...
http://wdtvforum.com/main/index.php?topic=59.msg3273#msg3273 (http://wdtvforum.com/main/index.php?topic=59.msg3273#msg3273)

I wasn't to lucky with this adapter on the wdtv but we'll see - maybe you are  :)
Title: Re: *experimental* wireless usb support package
Post by: Alwo on April 29, 2009, 04:55:49 AM
Hi all,

maybe someone can send me the config files to
setup my Wlan Stick with the WD TV. (net.config and so on ..)
I tried everything I read here, but my Wlan Stick
doesn`t connect to my Router :(

My System:
Stick: D-link DWL-G122 Vers. C1
Router IP 10.0.0.138
Router Wlan Name: AlwosWlan
Router WAP/PSK Code: 54EE857999
PC IP 10.0.0.1

Files on my Usb Stick:
mesages.txt
net.config
net.mounts
root.bin
wdtv.bin
wdtv.ver
wdtv.ver~
webserver.app.bin
wireless-mod.app.bin
wpa_supplicant.conf

Sorry for my bad english, i am from austria and
a newbie on WD TV!

Thank you all
Email: alwo@inode.at
Title: Re: *experimental* wireless usb support package
Post by: coasting on April 29, 2009, 06:54:00 AM
Hallo an Österreich :)

antworte Dir mal in Deutsch. Also kann Dir schon mal bestätigen, das es mit diesem WLAN Stick funktioniert. Leider sind die Infos wie es funktioniert, nicht sonderlich gut zu finden. So sehr ich den Enthusiasmus der Entwickler hier schätze, aber das Forum ist nicht sonderlich gut organisiert. Um es mal freundlich auszudrücken :)

Bei mir zu Hause funzt es nur mit der WPA Verschlüsselung. Die WEP Geschichte, so wie am Anfang dieses Threads und wie im Wiki beschrieben, geht nicht. Warum, keine Ahnung. Ahso, sehe gerade das Du Deinen WPA Schlüssel gepostet hat. Sieh mal zu, das Du den zu Hause wieder änderst :) Vielleicht liest Dein Nachbar ja hier auch mit...

Du benötigst die EXT3-0.8.7.2 Binaries und den wireless-mod.app.bin. Du kannst auch die neueren Packs versuchen, aber die habe ich noch nicht getestet. Den WDLX Mod kannste auch probieren, aber der lief bei mir nicht. Zudem brauchste hierfür einen anderen wireless.bin

In die net.config trägst Du folgendes ein:

Code: [Select]
#
# Network configuration file

HOST=wdtv

ifconfig rausb0 up

wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

DHCP=no
IP=10.0.0.1xx # IP des Sticks
GW=10.0.0.138 # IP des Routers
NM=255.255.255.0 # Netmask
DNS1=10.0.0.138 # DNS Server intern/extern
DNS2=212.216.172.62 # DNS Server extern

NTP=pool.ntp.org # Sollte gestzt werden, da die Box die Zeit nicht behält.

Und in die wpa_supplicant.conf kommt folgendes :

Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="AlwosWlan"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="54EE857999"
}

Aber wie schon gesagt, ändere den WPA Schlüssel zu Hause...

Lies auch die Beiträge von cionci hier, der hatte die selben Probleme.

coasting

Hi all,

maybe someone can send me the config files to
setup my Wlan Stick with the WD TV. (net.config and so on ..)
I tried everything I read here, but my Wlan Stick
doesn`t connect to my Router :(

My System:
Stick: D-link DWL-G122 Vers. C1
Router IP 10.0.0.138
Router Wlan Name: AlwosWlan
Router WAP/PSK Code: 54EE857999
PC IP 10.0.0.1

Files on my Usb Stick:
mesages.txt
net.config
net.mounts
root.bin
wdtv.bin
wdtv.ver
wdtv.ver~
webserver.app.bin
wireless-mod.app.bin
wpa_supplicant.conf

Sorry for my bad english, i am from austria and
a newbie on WD TV!

Thank you all
Email: alwo@inode.at
Title: Re: *experimental* wireless usb support package
Post by: cionci on April 29, 2009, 07:12:31 AM
Add

sleep 5

at the end of net.config ;)
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 29, 2009, 08:33:23 AM
I've managed to install the latest version of ext3-boot (0.9.2) and got both NFS and Samba working.
However I have one problem I haven't been able to resolve. I get a large number of packet
overruns.

"ifconfig rausb0" produces

Quote
rausb0    Link encap:Ethernet  HWaddr 00:23:CD:B9:B6:AB 
          inet addr:192.168.0.12  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:639707 errors:0 dropped:44632 overruns:44632 frame:44632
          TX packets:463167 errors:0 dropped:79 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:448222628 (427.4 MiB)  TX bytes:168745732 (160.9 MiB)

There do seem to be a large number of dropped packets and overruns. I'm wondering if
the WDTV chip is just not fast enough to process the packets it receives without
overruns or if there's something wrong the USB wifi stick.

I'm using a BlueNext BN-WD54G USB wireless stick (rt73 compatible chipset). I'd really appreciate
it if someone else with a working wireless usb installation could check to see if they also get a
similar number of overruns.
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on April 29, 2009, 10:59:14 AM
I'm using a BlueNext BN-WD54G USB wireless stick (rt73 compatible chipset). I'd really appreciate
it if someone else with a working wireless usb installation could check to see if they also get a
similar number of overruns.
My rt73 based Linksys WUSB54GC seems to work fine.
The result of iwconfig is quite different than yours, probably because I'm using WPA2 encryption (wpa_supplicant).
It doesn't seem to show overrun values. Maybe I should look elsewhere?

Code: [Select]
# iwconfig rausb0
rausb0    RT73 WLAN  ESSID:"**********************"
          Mode:Managed  Frequency=2.447 GHz  Access Point: **:**:**:**:**:**
          Bit Rate=54 Mb/s
          RTS thr:off   Fragment thr:off
          Encryption key:****-****-****-****-****-****-****-****   Security mode:open
          Link Quality=82/100  Signal level:-50 dBm  Noise level:-79 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 29, 2009, 12:20:14 PM
I'm using a BlueNext BN-WD54G USB wireless stick (rt73 compatible chipset). I'd really appreciate
it if someone else with a working wireless usb installation could check to see if they also get a
similar number of overruns.
My rt73 based Linksys WUSB54GC seems to work fine.
The result of iwconfig is quite different than yours, probably because I'm using WPA2 encryption (wpa_supplicant).
It doesn't seem to show overrun values. Maybe I should look elsewhere?

Code: [Select]
# iwconfig rausb0
rausb0    RT73 WLAN  ESSID:"**********************"
          Mode:Managed  Frequency=2.447 GHz  Access Point: **:**:**:**:**:**
          Bit Rate=54 Mb/s
          RTS thr:off   Fragment thr:off
          Encryption key:****-****-****-****-****-****-****-****   Security mode:open
          Link Quality=82/100  Signal level:-50 dBm  Noise level:-79 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Thanks. Could you try "ifconfig rasub0"?
Title: Re: *experimental* wireless usb support package
Post by: Alwo on April 29, 2009, 11:07:46 PM
Vielen Dank Coasting,

hab die beiden files am stick so angepasst (auch die ip die ich für das wd tv haben will und das sleep am ende)
aber genau wie davor blinkt der wlan stick immer mal wieder nur kurz beim hochfahren :(

die files net.config und wpa_supplicant.config gehören doch zur firmware in die root des memory sticks?

lg alwo
Title: Re: *experimental* wireless usb support package
Post by: coasting on April 30, 2009, 03:05:21 AM
Richtig. Sehe heute Abend nochmal zu Hause nach wie meine Dateien genau aussehen, dann poste ich die mal hier 1:1... Am Router bzw. an den Einstellungen des Routers liegt es aber nicht? Haste evtl. einen MAC Filter laufen? Wird die ESSID vom Router gesendet? Sind noch andere WLAN Geräte im Netz? Versuch auch mal den Channel zu wechseln.

Melde mich heute Abend nochmal.

Coasting

Vielen Dank Coasting,

hab die beiden files am stick so angepasst (auch die ip die ich für das wd tv haben will und das sleep am ende)
aber genau wie davor blinkt der wlan stick immer mal wieder nur kurz beim hochfahren :(

die files net.config und wpa_supplicant.config gehören doch zur firmware in die root des memory sticks?

lg alwo

Title: Re: *experimental* wireless usb support package
Post by: pcdthebum1 on April 30, 2009, 08:06:41 AM
I hate to post again, but I am trying to figure out if I should keep this adapter or just return it. has anyone had any luck with the TEW424UB? I have tried every different technique outlined in the forums with no luck. The adapter seems recognized but does not get drivers or something, I am not linux saavey, but I am trying.
Thanks
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 30, 2009, 08:37:16 AM
I hate to post again, but I am trying to figure out if I should keep this adapter or just return it. has anyone had any luck with the TEW424UB? I have tried every different technique outlined in the forums with no luck. The adapter seems recognized but does not get drivers or something, I am not linux saavey, but I am trying.
Thanks

If it's the "TEW-424UB A"  it should work since it;s based in a Zydas 1211 chipset. Post your net.config and I can have a look if you want.
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on April 30, 2009, 09:34:57 AM
Can anyone please help me ?
I have the ext3-boot 0.9.2 and wireless-mod.app.bin 0.0.3
The wifi usb is zydas
With no encryption i manage to connect to the network, so the usb wifi dongle works fine.
With WPA-PSK encryption the wdtv is dissasociated every 50 seconds.

i tried with the following configuration:

in net.config :

ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf


in wpa_supplicant.conf :
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="tzo"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="blablabla"
}

event if i try to use WPA-PSK, in the message.txt i got the following message:

Jan  1 00:00:44 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:00:45 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:00:45 wdtv user.notice kernel: vendor_id = 0ace
Jan  1 00:00:45 wdtv user.notice kernel: product_id = 1215
Jan  1 00:00:45 wdtv user.notice kernel: USB 2.0 Host
Jan  1 00:00:45 wdtv user.notice kernel: Release Ver = 4810
Jan  1 00:00:45 wdtv user.notice kernel: EEPROM Ver = 4810
Jan  1 00:00:45 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:00:45 wdtv user.err kernel: PA type: 0
Jan  1 00:00:45 wdtv user.warn kernel: PHYNEWLayout = 1
Jan  1 00:00:45 wdtv user.warn kernel: Airoha AL2230S_RF
Jan  1 00:00:45 wdtv user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:00:45 wdtv user.debug kernel: OverWrite CR47 = 0x1C
Jan  1 00:00:45 wdtv user.debug kernel: zd1205_config: EEP(HWFeature)=0x580
Jan  1 00:00:45 wdtv user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:00:45 wdtv user.warn kernel: Region:48
Jan  1 00:00:45 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:45 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:00:46 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:46 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:47 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:47 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:47 wdtv user.debug kernel: keybuf data
Jan  1 00:00:47 wdtv user.debug kernel:
Jan  1 00:00:47 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:47 wdtv user.debug kernel: keybuf data
Jan  1 00:00:47 wdtv user.debug kernel:
Jan  1 00:00:47 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:47 wdtv user.debug kernel: keybuf data
Jan  1 00:00:47 wdtv user.debug kernel:
Jan  1 00:00:47 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:47 wdtv user.debug kernel: keybuf data
Jan  1 00:00:47 wdtv user.debug kernel:
Jan  1 00:00:47 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:47 wdtv user.debug kernel: keybuf data
Jan  1 00:00:47 wdtv user.debug kernel:
Jan  1 00:00:47 wdtv user.debug kernel: Update CardSetting
Jan  1 00:00:48 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:48 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:48 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:49 wdtv user.debug kernel: chkpnt 001
Jan  1 00:00:51 wdtv user.err kernel: Rx Disasoc from AP(Rsn:3),set DIS_CONNECT_SET


i attach the full message.txt log file
Title: Re: *experimental* wireless usb support package
Post by: pcdthebum1 on April 30, 2009, 09:55:23 AM
If it's the "TEW-424UB A"  it should work since it;s based in a Zydas 1211 chipset. Post your net.config and I can have a look if you want.

I originally bought it because the wdtv wiki said it was
Trendnet   TEW-424UB   zd1211   0ace   1211   
Now that you ask your question, I look back to my first question and see that it says
Jan  1 00:00:35 (none) user.notice root:  [0bda:8189] 1-2( 2.00,480m) RTL8187B_WLAN_Adapter/00e04c000001

meaning that the version I have is based on realtek, which is not supported yet correct? So I should return it and find something that will work...
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 30, 2009, 10:13:20 AM
If it's the "TEW-424UB A"  it should work since it;s based in a Zydas 1211 chipset. Post your net.config and I can have a look if you want.

I originally bought it because the wdtv wiki said it was
Trendnet   TEW-424UB   zd1211   0ace   1211   
Now that you ask your question, I look back to my first question and see that it says
Jan  1 00:00:35 (none) user.notice root:  [0bda:8189] 1-2( 2.00,480m) RTL8187B_WLAN_Adapter/00e04c000001

meaning that the version I have is based on realtek, which is not supported yet correct? So I should return it and find something that will work...

Pretty much yes. I don't think the wireless mod supports the realtek chipset.

List of some Zydas 1211 USB dongles (http://zydas.rapla.net/)

Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on April 30, 2009, 10:15:02 AM
Thanks. Could you try "ifconfig rasub0"?

OK, sorry. I thought It was iwconfig :)

Here is the result:
Quote
# ifconfig rausb0
rausb0    Link encap:Ethernet  HWaddr **:**:**:**:**:**
          inet addr:*.*.*.*  Bcast:*.*.*.*  Mask:*.*.*.*
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3790 errors:0 dropped:0 overruns:0 frame:0
          TX packets:546 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:393723 (384.4 KiB)  TX bytes:81680 (79.7 KiB)

#
Title: Re: *experimental* wireless usb support package
Post by: coasting on April 30, 2009, 12:34:12 PM
Hallo...

also, meine net.config sieht so aus:

Code: [Select]

HOST=wdtv

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

DHCP=no
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1



...und meine wpa_supplicant.conf so:

Code: [Select]

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="WLAN"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="-------------"
}


Damit funktioniert es. Wenn es bei Dir nicht geht, überprüfe noch einmal das Du die richtige FW (EXT3) mit der richtigen Wireless.mod.bin benutzt. Irgendwo im Thread wurde von cionci auch beschrieben wie man überprüfen kann, ob der Stick das WLAN Netz überhaupt sieht. Mit Hilfe von iwlist rausb0 scanning kannste das überprüfen. Die Ausgabe kann man in eine TXT Datei umleiten, die dann auf den Memory-Stick geschrieben wird. Schau mal ab Seite 12...

Hoffe das hilft. Dieser Thread ist schon verdammt unübersichtlich. Die wichtigen Infos sind über zig Seiten / Threads im Forum verteilt. Leider gibt es (noch) keine zentrale Stelle wo man etwas nachlesen könnte. Zudem ist das Wiki nicht genau genug...

coasting

Vielen Dank Coasting,

hab die beiden files am stick so angepasst (auch die ip die ich für das wd tv haben will und das sleep am ende)
aber genau wie davor blinkt der wlan stick immer mal wieder nur kurz beim hochfahren :(

die files net.config und wpa_supplicant.config gehören doch zur firmware in die root des memory sticks?

lg alwo



-----ENGLISH ONLY PLEASE-----
Title: Re: *experimental* wireless usb support package
Post by: thenegus on April 30, 2009, 01:19:52 PM
Thanks. Could you try "ifconfig rasub0"?

OK, sorry. I thought It was iwconfig :)

Here is the result:
Quote
# ifconfig rausb0
rausb0    Link encap:Ethernet  HWaddr **:**:**:**:**:**
          inet addr:*.*.*.*  Bcast:*.*.*.*  Mask:*.*.*.*
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3790 errors:0 dropped:0 overruns:0 frame:0
          TX packets:546 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:393723 (384.4 KiB)  TX bytes:81680 (79.7 KiB)

#

Thanks again.
Title: Re: *experimental* wireless usb support package
Post by: El`Drako on April 30, 2009, 11:51:21 PM
Hi, all
I'm from Russia. First, sorry for my very bad english.
Help, please.
Now about the problem - can't configure the wi-fi adapter 3com 3CRUSB10075 (zd1211b   0ace:1215) in mode Ad-Hoc with my PCI Wi-Fi D-Link. They establish a connection, but the packets are not passed, and "eth0" (wi-fi) in WDTV not assigned a IP-address (both, static and with DHCP).
My logs below:
Quote
#
# Network configuration file
#You can override the hostname here:

HOST=wdtv

ifconfig eth0 up
sleep 5
iwconfig eth0 essid wd_tv key off rate auto mode Ad-Hoc channel auto > /boot/log.txt &2>1

#iwconfig $MDEV essid wdtvhd key "s:5851426023111" rate auto channel 6 > /boot/log.txt &2>1
sleep 5
iwconfig commit
iwconfig >> /boot/log_iwconfig.txt

iwlist $MDEV scanning > /boot/log.txt
echo "--------- ifconfig -a -----------" >> /boot/log.txt
ifconfig -a >> /boot/log.txt

#
# Dynamic IP Configuration:

#DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.4
GW=192.168.1.2
NM=255.255.255.0
DNS1=192.168.1.2
DNS2=192.168.1.1

sleep 5

echo "-------- ifconfig after IP settings ------------" >> /boot/log.txt
ifconfig -a >> /boot/log.txt

log.txt
Quote
eth0      Scan completed :
          Cell 01 - Address: 02:60:97:D6:C2:09
                    ESSID:"wd_tv"
                    Mode:Ad-Hoc
                    Frequency:2.437 GHz (Channel 6)
                    Extra:SignalStrength=100 %,LinkQuality:24%
                    Encryption key:off
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
                    Extra:bcn_int=100

--------- ifconfig -a -----------
eth0      Link encap:Ethernet  HWaddr 00:16:E0:07:55:F0 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:267 errors:0 dropped:0 overruns:0 frame:0
          TX packets:267 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:25557 (24.9 KiB)  TX bytes:25557 (24.9 KiB)
Quote
--------- iwlist  scanning -----------
eth0      802.11b/g NIC  ESSID:"wd_tv" 
          Mode:Ad-Hoc  Frequency=2.437 GHz  Cell: 02:60:97:D6:C2:09   
          Bit Rate:1 Mb/s   
          Retry:off   RTS thr=9999 B   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
Quote
Jan  1 00:01:11 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:01:12 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:12 wdtv user.notice kernel: vendor_id = 0ace
Jan  1 00:01:12 wdtv user.notice kernel: product_id = 1215
Jan  1 00:01:12 wdtv user.notice kernel: USB 2.0 Host
Jan  1 00:01:12 wdtv user.notice kernel: Release Ver = 4810
Jan  1 00:01:12 wdtv user.notice kernel: EEPROM Ver = 4810
Jan  1 00:01:12 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:12 wdtv user.err kernel: PA type: 0
Jan  1 00:01:12 wdtv user.warn kernel: PHYNEWLayout = 1
Jan  1 00:01:12 wdtv user.warn kernel: Airoha AL2230S_RF
Jan  1 00:01:12 wdtv user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:01:12 wdtv user.debug kernel: zd1205_config: EEP(HWFeature)=0x80
Jan  1 00:01:12 wdtv user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:01:12 wdtv user.warn kernel: Region:16
Jan  1 00:01:12 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:12 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:01:12 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:13 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:13 wdtv user.warn kernel: rtusb init --->
Jan  1 00:01:13 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:14 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:17 wdtv user.debug kernel: keybuf data
  • :

Jan  1 00:01:17 wdtv user.debug kernel:
Jan  1 00:01:17 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:01:17 wdtv user.warn kernel: We Can't Found Required Channel in ioctl_setfreq(2.4G)
Jan  1 00:01:19 wdtv user.warn kernel: Ibss Join, MAC_MODE:1, CHANNEL:6
Jan  1 00:01:19 wdtv user.err kernel: Mode: IBSS_MODE
Jan  1 00:01:19 wdtv user.debug kernel:  HashInsert macAddr =  data [6]:
Jan  1 00:01:19 wdtv user.debug kernel: 00 <7>1c <7>f0 <7>d7 <7>1d <7>f3 <7>
Jan  1 00:01:19 wdtv daemon.notice statd[1719]: Version 1.1.5 Starting
Jan  1 00:01:19 wdtv daemon.notice statd[1719]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:23 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:23 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:30 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.1.4 GW=192.168.1.2
Jan  1 00:01:31 wdtv user.notice root: Testing static IP assignment...
*****
Jan  1 00:01:46 wdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:46 wdtv user.notice root: IP Assignment failed. Trying DHCP
Jan  1 00:02:19 wdtv user.warn kernel:  ReJoin to
Jan  1 00:02:21 wdtv user.warn kernel: Ibss Join, MAC_MODE:1, CHANNEL:6
Jan  1 00:02:21 wdtv user.err kernel: Mode: IBSS_MODE
IP PC: 192.168.1.2
IP wi-fi pc: 192.168.1.3
IP GW PC: 192.168.1.1

Actually, in this mode, they can work? Or need buy an access point?

Firmware VERSION='1.02.07-ext3-boot-0.9.2' and this latest wmod-003.
Title: Re: *experimental* wireless usb support package
Post by: thenegus on May 01, 2009, 12:15:47 AM
Hi, all
I'm from Russian. First, sorry for my very bad english.
Help, please.
Now about the problem - can't configure the wi-fi adapter 3com 3CRUSB10075 (zd1211b   0ace:1215) in mode Ad-Hoc with my PCI Wi-Fi D-Link. They establish a connection, but the packets are not passed, and "eth0" (wi-fi) in WDTV not assigned a IP-address (both, static and with DHCP).
My logs below:
Quote
#
# Network configuration file
#You can override the hostname here:

HOST=wdtv

ifconfig eth0 up
sleep 5
iwconfig eth0 essid wd_tv key off rate auto mode Ad-Hoc channel auto > /boot/log.txt &2>1

#iwconfig $MDEV essid wdtvhd key "s:5851426023111" rate auto channel 6 > /boot/log.txt &2>1
sleep 5
iwconfig commit
iwconfig >> /boot/log_iwconfig.txt

iwlist $MDEV scanning > /boot/log.txt
echo "--------- ifconfig -a -----------" >> /boot/log.txt
ifconfig -a >> /boot/log.txt

#
# Dynamic IP Configuration:

#DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.4
GW=192.168.1.2
NM=255.255.255.0
DNS1=192.168.1.2
DNS2=192.168.1.1

sleep 5

echo "-------- ifconfig after IP settings ------------" >> /boot/log.txt
ifconfig -a >> /boot/log.txt

I think your first problem is the you're using the wrong interface. Change "ifconfig eth0 up" with "ifconfig $MDEV up".
Title: Re: *experimental* wireless usb support package
Post by: El`Drako on May 01, 2009, 03:44:42 AM
Quote from: Zorander
Here's the list of network device names:
arusb_lnx uses ath0
rt2870sta uses ra0
rt73 uses rausb0
zd1201 uses wlan0
and, not to be outdone, zd1211b uses eth1 (or eth0)
And if use $MDEV, then in log will also eth0.

Checked again with $MDEV - not working, and interface really eth0 (on logs).
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 01, 2009, 04:13:20 AM
My wifi usb dogle is zydas. I use 1.02.07-ext3-boot-0.9.2 with wireless-mod.app.bin 0.0.3
With no security or WEP, the system works fine but with WPA-PSK it's not working.

I tried different configuration (net.config and wpa_supplicant.conf) but no success.

Is there anything i can do ? Or WPA is not working at all with zydas ?

I really need to use WPA-PSK. Please help me.


PS. I have a computer with Ubutu which works fine with the wifi dongle and WPA-PSK so my guess is that it should work on WDTV device also. It's my first time with Linux, so be gentle :)
Title: Re: *experimental* wireless usb support package
Post by: thenegus on May 01, 2009, 04:38:50 AM
Quote from: Zorander
Here's the list of network device names:
arusb_lnx uses ath0
rt2870sta uses ra0
rt73 uses rausb0
zd1201 uses wlan0
and, not to be outdone, zd1211b uses eth1 (or eth0)
And if use $MDEV, then in log will also eth0.

Checked again with $MDEV - not working, and interface really eth0 (on logs).

What wireless encryption are you using?
Title: Re: *experimental* wireless usb support package
Post by: thenegus on May 01, 2009, 04:44:32 AM
My wifi usb dogle is zydas. I use 1.02.07-ext3-boot-0.9.2 with wireless-mod.app.bin 0.0.3
With no security or WEP, the system works fine but with WPA-PSK it's not working.

I tried different configuration (net.config and wpa_supplicant.conf) but no success.

Is there anything i can do ? Or WPA is not working at all with zydas ?

I really need to use WPA-PSK. Please help me.


PS. I have a computer with Ubutu which works fine with the wifi dongle and WPA-PSK so my guess is that it should work on WDTV device also. It's my first time with Linux, so be gentle :)

You're more likely to get help if you post your net.config and wpa_supplicant.conf files. A messages.txt file would also be helpful.
Title: Re: *experimental* wireless usb support package
Post by: El`Drako on May 01, 2009, 05:06:19 AM
Quote
What wireless encryption are you using?
WEP
Is it possible to use WPA in Ad-Hoc?

But the problem is already solved - had to be made public for the LAN network of wi-fi.
Quote
# iwconfig
lo        no wireless extensions.

eth0      802.11b/g NIC  ESSID:"wd_tv"
          Mode:Ad-Hoc  Frequency=2.437 GHz  Cell: 7E:E7:AE:D7:C2:09
          Bit Rate:11 Mb/s
          Retry:off   RTS thr=9999 B   Fragment thr:off
          Encryption key:****-****-****-****-****-****-**   Security mode:open
          Power Management:off
          Link Quality:96/100  Signal level:100/100  Noise level:0/100
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:5398  Invalid misc:18   Missed beacon:0

# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:16:E0:07:55:F0
          inet addr:192.168.0.2  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5839 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4248 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6066538 (5.7 MiB)  TX bytes:348654 (340.4 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:34599 errors:0 dropped:0 overruns:0 frame:0
          TX packets:34599 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2182280 (2.0 MiB)  TX bytes:2182280 (2.0 MiB)
Quote
# Network configuration file
#You can override the hostname here:

HOST=wdtv
group=workgroup

ifconfig $MDEV up
sleep 5
iwconfig $MDEV essid wd_tv key "s:pass" rate auto mode Ad-Hoc channel auto
sleep 5
iwconfig commit
sleep 5

DHCP=no
IP=192.168.0.2
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1
Title: Re: *experimental* wireless usb support package
Post by: Kater432 on May 01, 2009, 07:17:13 AM
My wifi usb dogle is zydas. I use 1.02.07-ext3-boot-0.9.2 with wireless-mod.app.bin 0.0.3
With no security or WEP, the system works fine but with WPA-PSK it's not working.

I tried different configuration (net.config and wpa_supplicant.conf) but no success.

Is there anything i can do ? Or WPA is not working at all with zydas ?

I really need to use WPA-PSK. Please help me.

I have the same Problem with my USB Stick (Zydas vendor_id = 0ace product_id = 1215)
with WEP or without security it works, with WPA it doesnt work. I think the there is a problem with the driver an wpa_supplicant, because my log (wpa_supplicant -D wext -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt)  I tried it with 0.8.7.2 and 0.9.2 with wireless-mod-0.3.app.bin
with (iwlist scanning > /boot/iwscan.txt) i can see my wlan

Code: [Select]
eth0    Cell 02 - Address: 00:1A:4F:93:9B:63
                    ESSID:"K9_K10_CHR1203FR2812"
                    Mode:Master
                    Frequency:2.462 GHz (Channel 11)
                    Extra:SignalStrength=100 %,LinkQuality:100%
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
                              48 Mb/s; 54 Mb/s
                    Extra:bcn_int=100
                    Extra:wpa_ie=dd180050f20101000050f20201000050f20201000050f2020000
                    Extra:rsn_ie=30140100000fac020100000fac040100000fac020000


Code: [Select]
Initializing interface 'eth0' conf '/boot/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/boot/wpa_supplicant.conf' -> '/boot/wpa_supplicant.conf'
Reading configuration file '/boot/wpa_supplicant.conf'
ctrl_interface='/boot/wpa_supplicant'
Priority group 0
   id=0 ssid='K9_K10_CHR1203FR2812'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=19 WE(source)=13 enc_capa=0x0
  capabilities: key_mgmt 0x0 enc 0x3
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:02:72:5e:72:74
wpa_driver_wext_set_wpa
Driver does not support WPA.
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Using existing control interface directory.
ctrl_iface bind(PF_UNIX) failed: Operation not permitted
ctrl_iface exists, but does not allow connections - assuming it was leftover from forced program termination
Could not unlink existing ctrl_iface socket '/boot/wpa_supplicant/eth0'
Failed to initialize control interface '/boot/wpa_supplicant'.
You may have another wpa_supplicant process already running or the file was
left by an unclean termination of wpa_supplicant in which case you will need
to manually remove this file before starting wpa_supplicant again.

Failed to add interface eth0
State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
Failed to disable WPA in the driver.
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6

Title: Re: *experimental* wireless usb support package
Post by: Kater432 on May 01, 2009, 08:43:53 AM
Now it works with zd1211b and WPA ove wpa_supplicant.
I change the line
wpa_supplicant -D wext -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
to
wpa_supplicant -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
and than my wd hd tv can connect to my wpa secured router.
i think the wpa_supplicant or the wext driver can wpa with the zd1211b.
See Log one post before. (wpa_driver_wext_set_wpa // Driver does not support WPA.)
my linux knowledge is very small but so it works.
has someone here a zydas chipset connect over wpa_supplicant with WPA secure?

Kater432 from Germany (sorry for my bad english)

Title: Re: *experimental* wireless usb support package
Post by: mazhas74 on May 01, 2009, 12:01:50 PM
Hi,

Still cannot use WPA :( (WEP is working ok) with my SMC EZ Connect SMCWUSB-G (zd1211b). If I use wext driver, it says that "Driver does not support WPA." if I use otus, then it is registered with AP (I can see wdtv on the AP device list) but it has no IP address (no matter if I use DHCP or static).
My net.config:

HOST=wdtv
ifconfig $MDEV up
wpa_supplicant -D otus -i $MDEV -c /boot/wpa_supplicant.conf -dd > /boot/wpa.txt
DHCP=yes

my wpa_supplicant.conf:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="PALANGA"
key_mgmt=WPA-PSK
psk="abcd"
}

from messages.txt:
Code: [Select]
...
Jan  1 00:02:39 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:02:40 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:02:40 wdtv user.notice kernel: vendor_id = 083a
Jan  1 00:02:40 wdtv user.notice kernel: product_id = 4505
Jan  1 00:02:40 wdtv user.notice kernel: USB 2.0 Host
Jan  1 00:02:40 wdtv user.notice kernel: Release Ver = 4810
Jan  1 00:02:40 wdtv user.notice kernel: EEPROM Ver = 4810
Jan  1 00:02:40 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:02:40 wdtv user.err kernel: PA type: 0
Jan  1 00:02:40 wdtv user.warn kernel: PHYNEWLayout = 1
Jan  1 00:02:40 wdtv user.warn kernel: Airoha AL2230S_RF
Jan  1 00:02:40 wdtv user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:02:40 wdtv user.debug kernel: OverWrite CR47 = 0x1C
Jan  1 00:02:40 wdtv user.debug kernel: zd1205_config: EEP(HWFeature)=0x180
Jan  1 00:02:40 wdtv user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:02:40 wdtv user.warn kernel: Region:16
Jan  1 00:02:40 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:02:40 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:02:42 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:02:42 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:02:42 wdtv user.warn kernel: rtusb init --->
Jan  1 00:02:43 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:02:43 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:02:49 wdtv daemon.notice statd[2024]: Version 1.1.5 Starting
Jan  1 00:02:49 wdtv daemon.notice statd[2024]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:02:53 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:02:53 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)

from wpa.txt:
Code: [Select]
...
WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 00 8a 00 10 00 00 00 00 00 00 00 04 2c c1 27 ef d3 23 36 39 23 5a 47 6a 84 22 a2 4e cd b9 a0 17 ac 2f 33 94 1e dd 92 61 e4 b2 76 34 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
wpa_driver_otus_get_bssid :  0:16:b6:d9:22:44
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:16:b6:d9:22:44 (ver=2)
WPA: Renewed SNonce - hexdump(len=32): be d0 dc 4d ea 1a 4e 41 37 2a 1e 2f 88 32 93 a1 fc 2e 7b cb 79 1a f8 ed 3a 2c b7 ef f1 63 87 5d
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 04 01 00 00 50 f2 02
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 0a 00 10 00 00 00 00 00 00 00 04 be d0 dc 4d ea 1a 4e 41 37 2a 1e 2f 88 32 93 a1 fc 2e 7b cb 79 1a f8 ed 3a 2c b7 ef f1 63 87 5d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 16 80 b9 ec be 1b fa 52 14 5e 95 9a d8 0d 59 4c 00 18 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 04 01 00 00 50 f2 02
RX EAPOL from 00:16:b6:d9:22:44
RX EAPOL - hexdump(len=129): 01 03 00 7d fe 01 ca 00 10 00 00 00 00 00 00 00 05 2c c1 27 ef d3 23 36 39 23 5a 47 6a 84 22 a2 4e cd b9 a0 17 ac 2f 33 94 1e dd 92 61 e4 b2 76 34 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1a ad a7 fc b9 1f 6f e4 b2 db bb 76 e1 b9 0f 62 00 1e dd 1c 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2 02 00 00
IEEE 802.1X RX: version=1 type=3 length=125
  EAPOL-Key type=254
  key_info 0x1ca (ver=2 keyidx=0 rsvd=0 Pairwise Install Ack MIC)
  key_length=16 key_data_length=30
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 05
  key_nonce - hexdump(len=32): 2c c1 27 ef d3 23 36 39 23 5a 47 6a 84 22 a2 4e cd b9 a0 17 ac 2f 33 94 1e dd 92 61 e4 b2 76 34
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 1a ad a7 fc b9 1f 6f e4 b2 db bb 76 e1 b9 0f 62
WPA: RX EAPOL-Key - hexdump(len=129): 01 03 00 7d fe 01 ca 00 10 00 00 00 00 00 00 00 05 2c c1 27 ef d3 23 36 39 23 5a 47 6a 84 22 a2 4e cd b9 a0 17 ac 2f 33 94 1e dd 92 61 e4 b2 76 34 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1a ad a7 fc b9 1f 6f e4 b2 db bb 76 e1 b9 0f 62 00 1e dd 1c 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2 02 00 00
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:16:b6:d9:22:44 (ver=2)
WPA: IE KeyData - hexdump(len=30): dd 1c 00 50 f2 01 01 00 00 50 f2 02 02 00 00 50 f2 04 00 50 f2 02 01 00 00 50 f2

Any ideas what to try next?
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 01, 2009, 12:39:07 PM
@Kater432

Can you please post you config files? I tried you suggestion with no success.

my config files are:

wpa_supplicant.conf
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="mclink"
key_mgmt=WPA-PSK
psk="123456789123456789"
}

net.config
HOST=wdtv
#MTU=9000
DHCP=yes
ifconfig $MDEV up
wpa_supplicant -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt


in wpa.txt i have the following:

Initializing interface 'eth0' conf '/boot/wpa_supplicant.conf' driver 'otus' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/boot/wpa_supplicant.conf' -> '/boot/wpa_supplicant.conf'
Reading configuration file '/boot/wpa_supplicant.conf'
ctrl_interface='/tmp/wpa_supplicant' - here you have /boot/wpa_supplicant...
.............
WPA: 4-Way Handshake failed - pre-shared key may be incorrect

I'm sure that the PSK is correct.

What could be the problem ?
Title: Re: *experimental* wireless usb support package
Post by: mazhas74 on May 01, 2009, 02:26:06 PM
Hello again,

Finally  ;D got it working zd1211b with WPA-PSK
For me it works only with TKIP, not AES (AES is faster?). Also I put psk in hex (without quotes), generated using http://www.wireshark.org/tools/wpa-psk.html

my working files:
HOST=WDTV1
ifconfig $MDEV up
wpa_supplicant -Bw -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
DHCP=no
IP=192.168.50.10
GW=192.168.50.254
NM=255.255.255.0
DNS1=192.168.50.254

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="PALANGA"
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
psk=166a96bc2bbab2a62b52a9bc4e65042e73e2d17836297f573ba64c28cc05ec99
}
Title: Re: *experimental* wireless usb support package
Post by: mazhas74 on May 01, 2009, 02:42:37 PM
AES is working too  ;) - needed to change on AP "TKIP/AES" to "AES" only and comment pairwise and group parameters
Title: Re: *experimental* wireless usb support package
Post by: gsm88 on May 01, 2009, 04:07:54 PM
@mazhas74

What is your wd tv firmware version, and the wireless.mod version?

Thanks!

Title: Re: *experimental* wireless usb support package
Post by: peibl on May 01, 2009, 11:19:39 PM
Hi I'm using a rt2870 based dongle but I cant make it work with my ** WDLXTV-0.5.2 **
Is there any step by step guide for dummies?
thanks  ;)
Title: Re: *experimental* wireless usb support package
Post by: Kater432 on May 02, 2009, 01:54:36 AM
I use a zd1211b Chipset with ext 0.9.2 an wireless-mod 0.3, the same config works also with ext 0.8.5.3

net.config
Code: [Select]
HOST=WDTV_Sony

# WPA
ifconfig $MDEV up
sleep 5
wpa_supplicant -Bw -D otus -i$MDEV -c/boot/wpa_supplicant.conf
sleep 10

DHCP=no
IP=192.168.11.23
GW=192.168.11.11
NM=255.255.255.0
DNS1=192.168.11.11
#DNS2=205.171.3.65
NTP=pool.ntp.org

i think the wpa_supplicant need a little time to connect to the ap. if i use sleep 10 then my wd doesnt get the  the ip *.23, it gets a ip from dhcp.

wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="HOME_SSID"
key_mgmt=WPA-PSK
psk="Key in ASCI"

Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 02, 2009, 01:58:17 AM
Finally it's working !
Thank you all for research and suggestions.

it seems that for zydas and wpa-psk i must use the otus driver and psk in hex

my config is:

HOST=WDTV
ifconfig $MDEV up
wpa_supplicant -Bw -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
DHCP=yes

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="mclink"
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
psk=166a96bc2bbab2a62b52a9bc4e65042e73e2d17836297f573ba64c28cc05ec99
}
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 02, 2009, 03:08:08 AM
I was happy too soon
After a WDTV restart, the connection is not working again....

The AP log files shows again
Saturday May 02, 2009 13:05:49 Associated: 00-02-72-73-F1-F1 st=0
Saturday May 02, 2009 13:06:01 Associated: 00-02-72-73-F1-F1 st=0
Saturday May 02, 2009 13:06:13 Associated: 00-02-72-73-F1-F1 st=0
Saturday May 02, 2009 13:06:25 Associated: 00-02-72-73-F1-F1 st=0
Saturday May 02, 2009 13:06:37 Associated: 00-02-72-73-F1-F1 st=0
Saturday May 02, 2009 13:06:49 Associated: 00-02-72-73-F1-F1 st=0
Title: Re: *experimental* wireless usb support package
Post by: shadow on May 02, 2009, 07:21:40 AM
@tzoshy

Why don't you try the following:

#ctrl_interface=/tmp/wpa_supplicant
network={
ssid="mclink"
proto=WPA
key_mgmt=WPA-PSK
#pairwise=TKIP
#group=TKIP
psk=166a96bc2bbab2a62b52a9bc4e65042e73e2d17836297f573ba64c28cc05ec99
}

 If it still doesn't work, but it get associated with the AP, try using static IP instead of DHCP.

 Good Luck!
Title: Re: *experimental* wireless usb support package
Post by: gsm88 on May 02, 2009, 07:41:29 AM
Working wifi on wd tv!

But my little problem is the transfer rate very slow, 300-500 kb/s the max speed!
How to boost the transfer rate?
I like transfer movies from my PC to Mybook (this connected the wdtv).

Thx
 
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 02, 2009, 09:35:01 AM
Performance could be slow due to poor writing performance on NTFS file system.
Try using an ext3 partition on your MyBook.

@tzoshy: add

sleep 5

at the end of net.config.

Title: Re: *experimental* wireless usb support package
Post by: mx5gr on May 02, 2009, 09:59:36 AM
I bought a Linksys WUSB600N Based on the rt2870sta chipset. I have loaded wireless-mod.app.bin (v 0.0.3) and I am using the wpa_supplicant.conf method, as WPA2-PSK is used in the network.


The debugfiles are:

dmesg.txt
Code: [Select]
mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
mii: No versions for exported symbols. Tainting kernel.
usbnet: No versions for exported symbols. Tainting kernel.
usbcore: registered new driver asix
/home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
usbcore: registered new driver dm9601
usbcore: registered new driver kaweth
usbcore: registered new driver MOSCHIP usb-ethernet driver
pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
cdc_ether: No versions for exported symbols. Tainting kernel.
usbcore: registered new driver cdc_ether
usbcore: registered new driver catc
drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new driver cdc_subset
usbcore: registered new driver net1080
usbcore: registered new driver plusb
usbcore: registered new driver rndis_host
usbcore: registered new driver gl620a
wireless_ext: No versions for exported symbols. Tainting kernel.
Loading wireless extentions module...
zd1201: Unknown symbol release_firmware
zd1201: Unknown symbol request_firmware
ZD1211B - version 2.19.2.9
usbcore: registered new driver zd1211b
arusb - version 0.0.0.999
usbcore: registered new driver Otus
rtusb init --->
usbcore: registered new driver rt2870
usbcore: registered new driver rt73
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)
program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO

messages.txt
Code: [Select]
Jan  1 00:00:34 (none) user.notice root:  [0951:160f] 1-1( 2.00,480m) DT Mini Slim/0019E06B7106A9215798079E
Jan  1 00:00:35 (none) user.notice root:  [1737:0071] 1-2( 2.00,480m) Dual-Band Wireless-N USB Network Adapter
Jan  1 00:00:35 (none) user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:36 (none) user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:36 (none) daemon.info utelnetd[320]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:00:46 (none) user.notice root: crazymounter: mounting devices
Jan  1 00:00:46 (none) user.notice root: /dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
Jan  1 00:00:46 (none) user.notice root: /dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:18 (none) user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:18 (none) user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:18 (none) user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:18 (none) user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:18 (none) user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:19 (none) user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:19 (none) user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:19 (none) user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:19 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:01:20 (none) user.warn kernel: zd1201: Unknown symbol release_firmware
Jan  1 00:01:20 (none) user.warn kernel: zd1201: Unknown symbol request_firmware
Jan  1 00:01:21 (none) user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:21 (none) user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:21 (none) user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:21 (none) user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:21 (none) user.warn kernel: rtusb init --->
Jan  1 00:01:21 (none) user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:21 (none) user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:24 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:24 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:02:01 (none) user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO

system.txt
Code: [Select]
/dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
/dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
/dev/sda1: LABEL="KINGSTON" UUID="3433-3231" TYPE="vfat"
/dev/loop0: LABEL="log-saver" TYPE="cramfs"
/dev/loop1: UUID="1b74a6e0-49c0-4b3e-b4dc-b6f66949d835" TYPE="ext3"
/dev/loop2: LABEL="wmod-003" TYPE="cramfs"
======================================
Displaying detected USB devices...
 [0951:160f] 1-1( 2.00,480m) DT Mini Slim/0019E06B7106A9215798079E
 [1737:0071] 1-2( 2.00,480m) Dual-Band Wireless-N USB Network Adapter
 [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
 [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
======================================
major minor  #blocks  name

   7     0          4 loop0
   7     1     131072 loop1
   7     2       2364 loop2
  31     0      16384 mtdblock0
  31     1        384 mtdblock1
  31     2       2176 mtdblock2
  31     3      13568 mtdblock3
  31     4        128 mtdblock4
  31     5        128 mtdblock5
   8     0    7880704 sda
   8     1    7879668 sda1
======================================
rootfs / rootfs rw 0 0
proc /proc proc rw,nodiratime 0 0
sysfs /sys sysfs rw 0 0
/dev/mtdblock3 / cramfs ro 0 0
none /proc proc rw,nodiratime 0 0
usb /proc/bus/usb usbfs rw 0 0
sysfs /sys sysfs rw 0 0
none /tmp tmpfs rw 0 0
none /etc/mdev.conf tmpfs rw 0 0
mdev /dev tmpfs rw 0 0
devpts /dev/pts devpts rw 0 0
/dev/sda1 /tmp/mnt/sda1 vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
/dev/loop0 /tmp/mnt/apps/log-saver cramfs ro 0 0
/dev/loop1 /tmp/mnt/opt ext3 rw,data=ordered 0 0
/dev/loop1 /tmp/mnt/opt ext3 rw,data=ordered 0 0
/dev/loop2 /tmp/mnt/apps/wireless-mod cramfs ro 0 0
none /osd/image/screen_saver.png tmpfs rw 0 0
none /osd/setup_about.xml tmpfs rw 0 0
/dev/sda1 /tmp/media/usb/USB1/3433-3231 vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
======================================
Module                  Size  Used by    Tainted: PF
rt73                  289040  0
rt2870sta             522448  0
arusb_lnx             450656  0
zd1211b               338256  0
wireless_ext            8240  4 rt73,rt2870sta,arusb_lnx,zd1211b
gl620a                  2448  0
rndis_host              3888  0
plusb                    752  0
net1080                 3808  0
cdc_subset              1184  0
catc                   11216  0
cdc_ether               2992  1 rndis_host
rtl8150                11200  0
pegasus                20048  0
mcs7830                 4496  0
kaweth                 15216  0
dm9601                 14320  0
asix                   18928  0
usbnet                 15424  8 gl620a,rndis_host,plusb,net1080,cdc_subset,cdc_ether,mcs7830,asix
mii                     3824  4 pegasus,mcs7830,asix,usbnet
em8xxx                846784  8
proc_pipe            1064688  0
llad                   95648  9 em8xxx
sr_mod                 12672  0
cdrom                  35424  1 sr_mod

I am using the following net.config &

net.config
Code: [Select]
#
# Network configuration file

ifconfig $MDEV up

# wpa_supplicant -Bw -D wext -i$MDEV -c/boot/wpa_supplicant.conf
# wpa_supplicant -Bw -D ralink -i$MDEV -c/boot/wpa_supplicant.conf
wpa_supplicant -Bw -D rt2870 -i $MDEV -c /boot/wpa_supplicant.conf > /boot/wpa.txt

sleep 10

#You can override the hostname here:
HOST=wdtv
# if you do not set a hostname,a random one is assigned.

# sleep 5

# attempt to set jumbo frames
# MTU=9000

#
# Dynamic IP Configuration:
#DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)
DHCP=no
IP=192.168.0.9
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

# sleep 5

wpa.supplicant
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="mycompany"
# uncomment next line if your ap doesn't broadcast ssid
scan_ssid=1
key_mgmt=WPA-PSK
psk="AB34289876"
}

It cannot get an IP and read files from the network. I use WPA2-PSK in my Access Point insfrastructure. I tried with -D wext in net.config, with -D ralink, to no effect.

I used the solution described in http://wdtvforum.com/main/index.php?topic=59.msg2333#msg2333 to no effect. The USB was visible from within Videos Folder, for example, but could not get an IP.

Anyone had this working? There is no alternative Ethernet interface on WDTV for further debugging.
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 02, 2009, 10:12:31 AM
Your USB ID seems to be not recognized by 2870 module. No hope to use that wifi dongle until Zorander insert USB ID 1737:0071 inside 2870 module source code.
Title: Re: *experimental* wireless usb support package
Post by: gsm88 on May 02, 2009, 10:29:15 AM
Performance could be slow due to poor writing performance on NTFS file system.
Try using an ext3 partition on your MyBook.

Thanks!

But, how to connect my xp based PC?
 :o
Title: Re: *experimental* wireless usb support package
Post by: mx5gr on May 02, 2009, 10:45:28 AM
Your USB ID seems to be not recognized by 2870 module. No hope to use that wifi dongle until Zorander insert USB ID 1737:0071 inside 2870 module source code.

Zoorander, please do if you read this... ;)
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 02, 2009, 12:45:08 PM
@tzoshy

Why don't you try the following:

#ctrl_interface=/tmp/wpa_supplicant
network={
ssid="mclink"
proto=WPA
key_mgmt=WPA-PSK
#pairwise=TKIP
#group=TKIP
psk=166a96bc2bbab2a62b52a9bc4e65042e73e2d17836297f573ba64c28cc05ec99
}

 If it still doesn't work, but it get associated with the AP, try using static IP instead of DHCP.

 Good Luck!


I tried both sollution, also i tried with sleep at the end, no success.
It's strange, because i managed to make it work 3 times (different config files :) ) but after i reset the device, the connection cannot be made. The only solution is (sometimes) to reset to factory defaults the router, and configure it again. But this is not working all the time.

I attach the latest files.
Any other ideas ?
Thank you

HOST=WDTV
ifconfig $MDEV up
sleep 5
iwlist $MDEV scanning > /boot/iwlist_scan.txt
#wpa_supplicant -Bw -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
wpa_supplicant -D otus -i $MDEV -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
DHCP=yes


ctrl_interface=/tmp/wpa_supplicant
network={
ssid="linksys_22"
proto=WPA
key_mgmt=WPA-PSK
pairwise=TKIP
group=TKIP
psk=c4df3bec4e1550037f84582e76d518f7f552eeb8992e00ff634a95d21c5cc956
}

Title: Re: *experimental* wireless usb support package
Post by: moustique on May 02, 2009, 06:59:50 PM
Hi there, I'm going to buy a D-Link DWA-140 (RT2870 chipset) today, anyone knows where I can find wireless-mod-wdlxtv app pack? Didn't find it @ B-Rad's site :(

Btw, is this wireless-mod-wdlxtv app pack made by B-Rad or Zorander?

Thanks.
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 02, 2009, 10:49:45 PM
@tzoshy: try this:

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your_ap_name"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="yourasciipass"
}

HOST=WDTV
ifconfig eth0 up
iwlist eth0 scanning > /boot/iwlist_scan.txt
sleep 5
wpa_supplicant -D otus -i eth0 -c /boot/wpa_supplicant.conf -d > /boot/wpa.txt
sleep 10
DHCP=yes
Title: Re: *experimental* wireless usb support package
Post by: tzoshy on May 03, 2009, 12:47:07 AM
@cionci
I tried, same results.

On Ubuntu computer, everything works fine, and without any problems, so the stick and the router are ok, it's only a config problem (i guess)
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 03, 2009, 04:46:42 AM
Hello everyone,

I bought a D-Link DWA-140 this afternoon, the chipset is RT2870. I've been trying to make it work with my WDTV according to http://wdtvforum.com/main/index.php?topic=59.msg2333#msg2333 (http://wdtvforum.com/main/index.php?topic=59.msg2333#msg2333) for several hours but still have no luck :(

There're 6 files in the root dir of my USB pen, which are:
Changelog
mod-wdlxtv.app.bin
net.config
net.mounts
README
RT2870STA.dat

My net.config looks like this:
Code: [Select]
HOST=wdtv
MTU=9000
DHCP=yes
[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
modprobe rt2870sta
ifconfig rausb0 up
udhcpc -H wdtv -i rausb0
sleep 5

And here's the messages.txt.0
Code: [Select]
Jan  1 00:00:56 (none) user.notice root: Inserting the modules...
Jan  1 00:00:56 (none) user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:56 (none) user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:57 (none) user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:01:03 (none) user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:01:03 (none) user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:01:04 (none) user.notice root: Generated new defaultHOST=WDTV-ef718
Jan  1 00:01:07 (none) user.warn kernel: rt2870sta: Unknown symbol wireless_send_event
Jan  1 00:01:07 (none) user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:07 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:01:08 (none) user.warn kernel: rtusb init --->
Jan  1 00:01:08 (none) user.warn kernel:
Jan  1 00:01:08 (none) user.warn kernel:
Jan  1 00:01:08 (none) user.warn kernel: === pAd = c5081000, size = 461808 ===
Jan  1 00:01:08 (none) user.warn kernel:
Jan  1 00:01:08 (none) user.warn kernel: <-- RTMPAllocAdapterBlock, Status=0
Jan  1 00:01:08 (none) user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:13 (none) user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:13 (none) user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:13 (none) user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:13 (none) user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:13 (none) user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:13 (none) user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:13 (none) user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:13 (none) user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:13 (none) user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:14 (none) user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:14 (none) user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:14 (none) user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:14 (none) user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:14 (none) user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:14 (none) user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:14 (none) user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:15 (none) user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:15 (none) user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:16 (none) user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:16 (none) user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:16 (none) user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:25 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:25 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:32 (none) user.info kernel: NTFS volume version 3.1.
Jan  1 00:01:33 (none) daemon.notice ntfs-3g[1504]: Version 2009.4.4 integrated FUSE 27
Jan  1 00:01:33 (none) daemon.notice ntfs-3g[1504]: Mounted /dev/sda1 (Read-Write, label "", NTFS 3.1)
Jan  1 00:01:33 (none) daemon.notice ntfs-3g[1504]: Cmdline options: force

system.txt.0
Code: [Select]
/dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
/dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
/dev/sda1: UUID="3A5C47725C472849" TYPE="ntfs"
/dev/loop0: LABEL="log-saver" TYPE="cramfs"
/dev/loop1: LABEL="wireless-mod-wdl" UUID="77d588b9-6fd7-4e42-8e1f-59c59329c98f" TYPE="ext2"
======================================
Displaying detected USB devices...
 [13fe:1f23] 1-1( 2.00,480m) STORE N GO/07910C890A53
 [07d1:3c09] 1-2( 2.00,480m) 802.11 n WLAN/1.0
 [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
 [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
======================================
major minor  #blocks  name

   7     0          4 loop0
   7     1      10240 loop1
  31     0      16384 mtdblock0
  31     1        384 mtdblock1
  31     2       2176 mtdblock2
  31     3      13568 mtdblock3
  31     4        128 mtdblock4
  31     5        128 mtdblock5
   8     0   15634432 sda
   8     1   15630400 sda1
======================================
rootfs / rootfs rw 0 0
proc /proc proc rw,nodiratime 0 0
sysfs /sys sysfs rw 0 0
/dev/mtdblock3 / cramfs ro 0 0
none /proc proc rw,nodiratime 0 0
usb /proc/bus/usb usbfs rw 0 0
sysfs /sys sysfs rw 0 0
none /tmp tmpfs rw 0 0
none /etc/mdev.conf tmpfs rw 0 0
mdev /dev tmpfs rw 0 0
devpts /dev/pts devpts rw 0 0
/dev/sda1 /tmp/mnt/sda1 fuse rw,user_id=0,group_id=0,allow_other 0 0
/dev/loop0 /tmp/mnt/apps/log-saver cramfs ro 0 0
/dev/loop1 /tmp/mnt/apps/mod-wdlxtv ext2 rw,nogrpid 0 0
none /osd/setup_about.xml tmpfs rw 0 0
======================================
Module                  Size  Used by    Tainted: PF
firmware_class          7776  0
gl620a                  2448  0
rndis_host              3888  0
plusb                    752  0
net1080                 3808  0
cdc_subset              1184  0
catc                   11216  0
cdc_ether               2992  1 rndis_host
rtl8150                11200  0
pegasus                20048  0
mcs7830                 4496  0
kaweth                 15216  0
dm9601                 14320  0
asix                   18928  0
usbnet                 15424  8 gl620a,rndis_host,plusb,net1080,cdc_subset,cdc_ether,mcs7830,asix
mii                     3824  4 pegasus,mcs7830,asix,usbnet
rt2870sta             560176  0
wireless_ext            8240  1 rt2870sta
em8xxx                846784  8
proc_pipe            1064688  0
llad                   95648  9 em8xxx
sr_mod                 12672  0
cdrom                  35424  1 sr_mod

RT2870STA.dat
Code: [Select]
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
SSID=steven
NetworkType=Infra
WirelessMode=9
Channel=6
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
PktAggregate=0
WmmCapable=1
AckPolicy=0;0;0;0
AuthMode=WPAPSK
EncrypType=AES
WPAPSK=mypskkey
PSMode=CAM
AutoRoaming=0
RoamThreshold=70
APSDCapable=0
APSDAC=0;0;0;0
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_BADecline=0
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0
AntDiversity=0
BeaconLostTime=4

dmesg.txt.0
Code: [Select]
Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #2 PREEMPT Mon Sep 15 20:20:41 CST 2008
Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
 BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Valid MEMCFG found at 0x10000fc0.
CPU revision is: 00019069
Determined physical RAM map:
 memory: 06fe0000 @ 10020000 (usable)
On node 0 totalpages: 94208
  DMA zone: 94208 pages, LIFO batch:31
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
Built 1 zonelists
Kernel command line: console=ttyS0
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 2048 (order: 11, 32768 bytes)
Using 148.500 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Calibrating delay loop... 292.86 BogoMIPS (lpj=146432)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
PCI: Initializing SMP863x/SMP865x PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
PCI: Region size is 16384KB
PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Created /proc/cpucache_info entry.
NTFS driver 2.1.25 [Flags: R/O].
fuse init (API version 7.3)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
SMP86xx led_rst (253:0): driver loaded.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: loaded (max 8 devices)
physmap flash device CS2: 1000000 at 48000000
CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Using physmap partition definition
Adding partition #1-#5
Creating 5 MTD partitions on "CS2: Physically mapped flash":
0x00000000-0x00060000 : "CS2-Part1"
0x00060000-0x00280000 : "CS2-Part2"
0x00280000-0x00fc0000 : "CS2-Part3"
0x00fc0000-0x00fe0000 : "CS2-Part4"
0x00fe0000-0x01000000 : "CS2-Part5"
physmap flash device CS3: 4000000 at 4c000000
CFI: Found no CS3: Physically mapped flash device at location zero
driver tangox-ehci-hcd, 10 Dec 2004
TangoX USB initializing...
tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
TangoX USB was initialized.
Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 252k freed
  Vendor: Verbatim  Model: STORE N GO        Rev: 5.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 31268864 512-byte hdwr sectors (16010 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 31268864 512-byte hdwr sectors (16010 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
attempt to access beyond end of device
loop0: rw=0, want=68, limit=8
attempt to access beyond end of device
loop0: rw=0, want=1028, limit=8
attempt to access beyond end of device
loop0: rw=0, want=12, limit=8
attempt to access beyond end of device
loop0: rw=0, want=1028, limit=8
attempt to access beyond end of device
loop0: rw=0, want=12, limit=8
attempt to access beyond end of device
loop0: rw=0, want=1252, limit=8
attempt to access beyond end of device
loop0: rw=0, want=1028, limit=8
UDF-fs: No partition found (1)
UDF-fs: No VRS found
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
cdrom: no version for "struct_module" found: kernel tainted.
cdrom: No versions for exported symbols. Tainting kernel.
llad: module license 'LGPL' taints kernel.
em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
rt2870sta: Unknown symbol wireless_send_event
wireless_ext: No versions for exported symbols. Tainting kernel.
Loading wireless extentions module...
rtusb init --->


=== pAd = c5081000, size = 461808 ===

 RTMPAllocAdapterBlock, Status=0
usbcore: registered new driver rt2870
mii: No versions for exported symbols. Tainting kernel.
usbnet: No versions for exported symbols. Tainting kernel.
usbcore: registered new driver asix
/home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
usbcore: registered new driver dm9601
usbcore: registered new driver kaweth
usbcore: registered new driver MOSCHIP usb-ethernet driver
pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new driver rtl8150
cdc_ether: No versions for exported symbols. Tainting kernel.
usbcore: registered new driver cdc_ether
usbcore: registered new driver catc
drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new driver cdc_subset
usbcore: registered new driver net1080
usbcore: registered new driver plusb
usbcore: registered new driver rndis_host
usbcore: registered new driver gl620a
firmware_class: No versions for exported symbols. Tainting kernel.
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)
NTFS volume version 3.1.


Please help me out, THANKS A LOT in advance!
Title: Re: *experimental* wireless usb support package
Post by: draadloos on May 03, 2009, 05:37:50 AM
:) Anybody got a hispeed (N-draft) wlan adapter with atheros otus working yet?

 8) Anybody got any 300mb wlan adapter running already?
Title: Re: *experimental* wireless usb support package
Post by: smartP on May 03, 2009, 06:35:47 AM
@moustique

what do you get when you run ifconfig and iwconfig?
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 03, 2009, 06:47:09 AM
@moustique

what do you get when you run ifconfig and iwconfig?

Hello smartP, how could I run ifconfig/iwconfig without network enabled? I don't know how I can login the WDTV...
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 03, 2009, 09:09:20 AM
Hi there, after spending more than 10 hours today, my DWA-140 still doens't work :(

However, after I use wireless-mod.app.bin instead of wireless-mod-wdlxtv.app.bin, the red LED on the DWA-140 starts flickering, although it's not be able to gain an IP from my router.

Here's the net.config that I'm currently using, I also enclosed the messages.txt, system.txt and dmesg.txt, please help me, thank you all.

I'm using WEP for the moment:

net.config
Code: [Select]
HOST=wdtv
MTU=9000
DHCP=yes
modprobe rt2870sta
ifconfig $MDEV up
iwconfig $MDEV essid steven key "13131313131313131313131313"
sleep 5
Title: Re: *experimental* wireless usb support package
Post by: peibl on May 03, 2009, 09:11:19 AM
@ smartP
I followed your instructions for a WLAN using rt2870 and only I got power on my dongle but no connection
I'm using ** WDLXTV-0.5.2 ** with wireless-mod-wdlxtv.app.bin the one you provided on this forum.
Can you help me?

EDIT: I've changed the wireless-mod-wdlxtv.app.bin for another one and now I have the power and the link light but I can't see my WD box on my network

Any suggestion ?
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 03, 2009, 09:52:35 AM
@cionci
I tried, same results.
Could access point be too far from wdtv ?
In my first attempts to get wifi working on WDTV, usb dongle cannot associate to AP for some distance related issue despite the same dongle associates to AP from the same place of WDTV if attached to a Windows notebook (70% signal quality).
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 03, 2009, 07:15:11 PM
@ smartP

I have the exactly same problem with peibl, if I use wireless-mod-wdlxtv.app.bin, my rt2870 based DWA-140 wouldn't even be powered on. If I use wireless-mod.app.bin, it can be powered on and the red LED is flickering.

In system.txt, I can see that rt2870sta dirver is loaded and used. In the admin page of my router, I can see that the DWA-140 can connect to the router, but it just cannot get any IP address, I've tried both DHCP "yes"/"no" in net.config but no luck.

I enclosed the log files @ http://wdtvforum.com/main/index.php?topic=59.msg4029#msg4029 (http://wdtvforum.com/main/index.php?topic=59.msg4029#msg4029), could you help me have a look at the logs? Thanks a lot.
Title: Re: *experimental* wireless usb support package
Post by: sirish19 on May 03, 2009, 08:33:07 PM
Hi All,

Total Noob to all of this networking but wondering if someone can help me out.  I have just bought the Buffalo Linkstation LS-CL 1 TB NAS drive with the idea of setting up a network to this and being able to connect my WDTV to this network.  So far, the LinkStation network is all working fine and I can see on all of my computers over the wireless network.

Having gone through this forum and seen some of the posts, I have flashed b-rad's WDLXTV 0.5.2 version to my WDTV. 

Next, I wanted to connect my WDTV to the network so I bought a Buffalo USB 2.0 LAN adapter (LUA2-U2-KGT) for the connection. However, when I connect this to my WDTV, no light is coming on the adapter and I don't see any IP address in the About section.

Does anyone have any ideas on what could be wrong?  Does there need to be some kind of driver for the adapter installed somewhere? 

Any help that you could give is greatly appreciated.
Title: Re: *experimental* wireless usb support package
Post by: peibl on May 04, 2009, 04:31:42 AM
Hi , finally I've got my dongle working but the WD box is giving me an IP that it's not in my network ,and it's always 192.168.0.3
Can some one help me please?
Title: Re: *experimental* wireless usb support package
Post by: smartP on May 04, 2009, 05:11:04 AM
hi moustique/peibl,

I've looked at your logs, but they don't tell me much I'm sorry to say.  :-[

Perhaps you can try my current setup. I've using Zorander's ext3-0.9.2 package with my updated wireless-mod... -> http://www.mediafire.com/file/rzdydjcyetj/wireless-mod.app-rt2870.zip (http://www.mediafire.com/file/rzdydjcyetj/wireless-mod.app-rt2870.zip)

Unzip to the root of your usb key. You should have the following files:
/RT2870STA.dat
/wireless-mod.app.bin
/<your wpa_supplicant.conf>
/wpa/wpa_cli
/wpa/wpa_passphrase
/wpa/wpa_supplicant

and add the following to your net.config

Quote
HOST=wdtv
/boot/wpa/wpa_supplicant -B -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
DHCP=yes

This uses the latest ralink drivers (v2.1.1.0) and wpa_supplicant (v0.6.9). I couldn't get the current version to work with my WPA2/AES setup.

Good luck!

note: this is the full list of devices supported in this driver:
   {USB_DEVICE(0x148F,0x2770)}, /* Ralink */
   {USB_DEVICE(0x148F,0x2870)}, /* Ralink */
   {USB_DEVICE(0x07B8,0x2870)}, /* AboCom */
   {USB_DEVICE(0x07B8,0x2770)}, /* AboCom */
   {USB_DEVICE(0x0DF6,0x0039)}, /* Sitecom 2770 */
   {USB_DEVICE(0x083A,0x7512)}, /* Arcadyan 2770 */
   {USB_DEVICE(0x0789,0x0162)}, /* Logitec 2870 */
   {USB_DEVICE(0x0789,0x0163)}, /* Logitec 2870 */
   {USB_DEVICE(0x0789,0x0164)}, /* Logitec 2870 */
   {USB_DEVICE(0x177f,0x0302)}, /* lsusb */
   {USB_DEVICE(0x0B05,0x1731)}, /* Asus */
   {USB_DEVICE(0x0B05,0x1732)}, /* Asus */
   {USB_DEVICE(0x0B05,0x1742)}, /* Asus */
   {USB_DEVICE(0x0DF6,0x0017)}, /* Sitecom */
   {USB_DEVICE(0x0DF6,0x002B)}, /* Sitecom */
   {USB_DEVICE(0x0DF6,0x002C)}, /* Sitecom */
   {USB_DEVICE(0x0DF6,0x002D)}, /* Sitecom */
   {USB_DEVICE(0x14B2,0x3C06)}, /* Conceptronic */
   {USB_DEVICE(0x14B2,0x3C28)}, /* Conceptronic */
   {USB_DEVICE(0x2019,0xED06)}, /* Planex Communications, Inc. */
   {USB_DEVICE(0x07D1,0x3C09)}, /* D-Link */
   {USB_DEVICE(0x07D1,0x3C11)}, /* D-Link */
   {USB_DEVICE(0x14B2,0x3C07)}, /* AL */
   {USB_DEVICE(0x050D,0x8053)}, /* Belkin */
   {USB_DEVICE(0x14B2,0x3C23)}, /* Airlink */
   {USB_DEVICE(0x14B2,0x3C27)}, /* Airlink */
   {USB_DEVICE(0x07AA,0x002F)}, /* Corega */
   {USB_DEVICE(0x07AA,0x003C)}, /* Corega */
   {USB_DEVICE(0x07AA,0x003F)}, /* Corega */
   {USB_DEVICE(0x1044,0x800B)}, /* Gigabyte */
   {USB_DEVICE(0x15A9,0x0006)}, /* Sparklan */
   {USB_DEVICE(0x083A,0xB522)}, /* SMC */
   {USB_DEVICE(0x083A,0xA618)}, /* SMC */
   {USB_DEVICE(0x083A,0x8522)}, /* Arcadyan */
   {USB_DEVICE(0x083A,0x7522)}, /* Arcadyan */
   {USB_DEVICE(0x0CDE,0x0022)}, /* ZCOM */
   {USB_DEVICE(0x0586,0x3416)}, /* Zyxel */
   {USB_DEVICE(0x0CDE,0x0025)}, /* Zyxel */
   {USB_DEVICE(0x1740,0x9701)}, /* EnGenius */
   {USB_DEVICE(0x1740,0x9702)}, /* EnGenius */
   {USB_DEVICE(0x0471,0x200f)}, /* Philips */
   {USB_DEVICE(0x14B2,0x3C25)}, /* Draytek */
   {USB_DEVICE(0x13D3,0x3247)}, /* AzureWave */
   {USB_DEVICE(0x083A,0x6618)}, /* Accton */
   {USB_DEVICE(0x15c5,0x0008)}, /* Amit */
   {USB_DEVICE(0x0E66,0x0001)}, /* Hawking */
   {USB_DEVICE(0x0E66,0x0003)}, /* Hawking */
   {USB_DEVICE(0x129B,0x1828)}, /* Siemens */
   {USB_DEVICE(0x157E,0x300E)},   /* U-Media */
   {USB_DEVICE(0x050d,0x805c)},   
   {USB_DEVICE(0x050d,0x815c)},
   {USB_DEVICE(0x1482,0x3C09)}, /* Abocom*/
   {USB_DEVICE(0x14B2,0x3C09)}, /* Alpha */
   {USB_DEVICE(0x04E8,0x2018)}, /* samsung */
   {USB_DEVICE(0x5A57,0x0280)}, /* Zinwell */
   {USB_DEVICE(0x5A57,0x0282)}, /* Zinwell */
   {USB_DEVICE(0x7392,0x7718)},
   {USB_DEVICE(0x7392,0x7717)},
   {USB_DEVICE(0x1737,0x0070)}, /* Linksys WUSB100 */
   {USB_DEVICE(0x1737,0x0071)}, /* Linksys WUSB600N */
   {USB_DEVICE(0x0411,0x00e8)}, /* Buffalo WLI-UC-G300N*/
   {USB_DEVICE(0x050d,0x815c)}, /* Belkin F5D8053 */
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 04, 2009, 06:02:50 AM
Hi , finally I've got my dongle working but the WD box is giving me an IP that it's not in my network ,and it's always 192.168.0.3
Can some one help me please?
Post net.config...
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 04, 2009, 06:20:39 AM
@peibl

Hi, I have the same problem as what you had before. Could you please tell me how you made your dongle work? Is it possible to show me your configuration? Thanks in advance.
Title: Re: *experimental* wireless usb support package
Post by: realtebo on May 04, 2009, 07:47:08 AM
1. Is the 0.0.3 the latest version avaiable? If yes, from where? Can you update the start post of this thread?

2. My WDTV with your excellent ext-boot 0.9.2 and the wilress-mod 0.0.3 worked in wifi for some weeks. Every some hours (max 6) the Wifi crash and I must reboot (detach from electric current and reattach).

Yesterday evening, another crash. The pen is full working. My Pc has been able to work with torrent client and amule client for 96 hours with it, so the pen is actually working.
BUT now, even after a new flash of 0.92 ext3, wdtv is NOT ABLE TO CONNECT TO MY LAN via Wifi. Why?

My net.config is unchanged:
Code: [Select]
# Network configuration file

ifconfig $MDEV up
iwconfig $MDEV essid OpenWrtWiFi

HOST=wdtv

#DHCP=yes

DHCP=no
IP=192.168.0.6
GW=192.168.0.1
NM=255.255.255.0
DNS1=81.29.230.1
DNS2=81.29.230.5

NTP=pool.ntp.org

My WiFi name is correct, IPs also are right. Why WDTV can't no more connect to WiFi? Why? ;( Now I must buy a usb-lan adapter ...
Title: Re: *experimental* wireless usb support package
Post by: Civuck on May 04, 2009, 11:55:49 AM
Does anyone have a Dlink DWL-G122 rev C1 working with WDLXTV 0.5.2?

My WDTV simply doesn't want to connect to my open access WiFi router.  The LEDs flash every 5 seconds or so but no IP is listed in the About screen.

What should my net.config file look like and do I need to make any other changes?

Title: Re: *experimental* wireless usb support package
Post by: medicineuk on May 04, 2009, 12:32:56 PM
Hi all

I'm trying to set up my WDTV with my Belkin Wireless G USB Adapter and have come around some problems. I have ext-boot 0.9.2 and the wilress-mod 0.0.3 installed after a lot of playing about with wpa_supplicant.conf and net.config I deiced to give up and try and get some help from the professionals. I have a number of logs below are the most recent, the USB Adapter seems to be active as I have a flashing green light but it can not connect to my WPA network. Any help would be amazing thanks guys.

wpa.txt
Code: [Select]
Initializing interface 'eth0' conf '/boot/wpa_supplicant.conf' driver 'otus' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/boot/wpa_supplicant.conf' -> '/boot/wpa_supplicant.conf'
Reading configuration file '/boot/wpa_supplicant.conf'
ctrl_interface='/tmp/wpa_supplicant'
Priority group 0
   id=0 ssid='2MISWELLS_REPEAT'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Could not configure driver to use managed mode
Could not set interface 'eth0' UP
WEXT: Operstate: linkmode=1, operstate=5
wpa_driver_otus_init: failed to set wpa_supplicant-based roaming
WEXT: Operstate: linkmode=0, operstate=6
Failed to initialize driver interface
Failed to add interface eth0
Cancelling scan request
Cancelling authentication timeout


message.txt
Code: [Select]
Jan  1 00:00:38 WDTV user.notice root: INIT: mounting app binaries...
Jan  1 00:00:38 WDTV user.notice root: Mounting /boot/log-saver.app.bin at /apps/log-saver
Jan  1 00:00:39 WDTV user.notice root: Mounting /boot/wireless-mod.app.bin at /apps/wireless-mod
Jan  1 00:00:40 WDTV user.notice root: Path set to /apps/wireless-mod/bin:/boot/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:42 WDTV user.notice root: vfat: Waiting for F46A-19E7 to mount
Jan  1 00:00:42 WDTV user.notice root: Polling detected drives...
Jan  1 00:00:42 WDTV user.notice root: xmount.scan: MDEV=sda1
Jan  1 00:00:42 WDTV user.notice root: /dev/sda1: LABEL="EFI" UUID="3F3C-1AF6" TYPE="vfat"
Jan  1 00:00:43 WDTV user.notice root: xmount.scan: Will not mount /dev/sda1 (vfat)
Jan  1 00:00:43 WDTV user.notice root: Waiting for /dev/sda2 to come online (UUID=F46A-19E7)...
Jan  1 00:00:44 WDTV authpriv.info dropbear[802]: Running in background
Jan  1 00:00:50 WDTV user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:50 WDTV user.info kernel: Loading wireless extentions module...
Jan  1 00:00:50 WDTV user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:07 WDTV user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:07 WDTV user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:07 WDTV user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:07 WDTV user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:07 WDTV user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:08 WDTV user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:08 WDTV user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:08 WDTV user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:08 WDTV user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:08 WDTV user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:08 WDTV user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:08 WDTV user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:08 WDTV user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:08 WDTV user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:09 WDTV user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:10 WDTV user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:11 WDTV user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:01:11 WDTV user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:11 WDTV user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:12 WDTV user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:12 WDTV user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:12 WDTV user.warn kernel: rtusb init --->
Jan  1 00:01:12 WDTV user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:13 WDTV user.warn kernel: idVendor = 0x50d, idProduct = 0x705a
Jan  1 00:01:13 WDTV user.notice root: net.agent: Called for rausb0
Jan  1 00:01:13 WDTV user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:19 WDTV daemon.notice statd[1740]: Version 1.1.5 Starting
Jan  1 00:01:19 WDTV daemon.notice statd[1740]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:25 WDTV user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:25 WDTV user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:29 WDTV user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:01:29 WDTV user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:01:30 WDTV user.warn kernel: => usb_rtusb_open
Jan  1 00:01:33 WDTV user.notice root: xmounter: entering stage2
Jan  1 00:01:33 WDTV user.notice root: Now mounted:
Jan  1 00:01:33 WDTV user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:33 WDTV user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:33 WDTV user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:33 WDTV user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:33 WDTV user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:33 WDTV user.notice root: /dev/sda2 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:33 WDTV user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:01:33 WDTV user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:33 WDTV user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:01:33 WDTV user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:33 WDTV user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:33 WDTV user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:33 WDTV user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:33 WDTV user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:33 WDTV user.notice root: /dev/loop0 on /apps/log-saver type cramfs (ro)
Jan  1 00:01:33 WDTV user.notice root: /dev/loop2 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:01:33 WDTV user.notice root: /dev/sda2 on /tmp/media/usb/USB1/F46A-19E7 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Title: Re: *experimental* wireless usb support package
Post by: peibl on May 04, 2009, 07:37:02 PM
Hi , finally I've got my dongle working but the WD box is giving me an IP that it's not in my network ,and it's always 192.168.0.3
Can some one help me please?
Post net.config...
@ cionci
here is my net.config
Code: [Select]
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
udhcpc -H wdtv -i rausb0


sleep 5

Title: Re: *experimental* wireless usb support package
Post by: peibl on May 04, 2009, 08:23:18 PM
@peibl

Hi, I have the same problem as what you had before. Could you please tell me how you made your dongle work? Is it possible to show me your configuration? Thanks in advance.
try with this one
http://www.mediafire.com/?dz1nmqloazm
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 04, 2009, 09:50:30 PM
Hi , finally I've got my dongle working but the WD box is giving me an IP that it's not in my network ,and it's always 192.168.0.3
Can some one help me please?
Post net.config...
@ cionci
here is my net.config
Code: [Select]
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
udhcpc -H wdtv -i rausb0


sleep 5


Try moving sleep 5 before udhcp and try logging udhcpc call:

udhcpc -H wdtv -i rausb0 > /boot/log.txt
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 04, 2009, 10:31:34 PM
Does anyone have a Dlink DWL-G122 rev C1 working with WDLXTV 0.5.2?
I have the same dongle and, at least for me, it associates to WPA encrypted networks only. I had no success on WEP or open networks.
Title: Re: *experimental* wireless usb support package
Post by: supahseb on May 06, 2009, 10:54:12 AM

For the DWA-140 (or any rt2870-based thing), I've updated the Wiki-Page with instructions.

See http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page
Title: Re: *experimental* wireless usb support package
Post by: medicineuk on May 06, 2009, 02:09:58 PM
After some paying about I think that I have got a bit closer to connection. My WPA.TXT now looks like this

Code: [Select]
Initializing interface 'rausb0' conf '/boot/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/boot/wpa_supplicant.conf' -> '/boot/wpa_supplicant.conf'
Reading configuration file '/boot/wpa_supplicant.conf'
Priority group 0
   id=0 ssid='2MISWELLS_REPEAT'
Initializing interface (2) 'rausb0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=19 WE(source)=14 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:1c:df:a0:7e:c0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
Added interface rausb0
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
Try to find non-WPA AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - non-WPA network not allowed
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 84 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:11:50:ba:8e:0c ssid='2MISWELLS_REPEAT' wpa_ie_len=0

It looks like it's finding and talking to the router but then having problems after that. Can any one explain to me what's going on here? 
Title: Re: *experimental* wireless usb support package
Post by: Civuck on May 06, 2009, 02:50:33 PM
Does anyone have a Dlink DWL-G122 rev C1 working with WDLXTV 0.5.2?
I have the same dongle and, at least for me, it associates to WPA encrypted networks only. I had no success on WEP or open networks.
I gather from scanning this thread that the EXT3-boot 0.9.1 firmware with 0.3 wireless-mod.app.bin is currently the only reliable way to get a D-Link DWL-G122 working with the WDTV with an open WiFi network.  Correct?

I've flashed to WDlxTV - can I still use the EXT3-Boot firmware?
Title: Re: *experimental* wireless usb support package
Post by: peibl on May 06, 2009, 09:09:07 PM

For the DWA-140 (or any rt2870-based thing), I've updated the Wiki-Page with instructions.

See http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page
It's working man thanx a lot!!
Title: Re: *experimental* wireless usb support package
Post by: moustique on May 07, 2009, 04:06:23 AM

For the DWA-140 (or any rt2870-based thing), I've updated the Wiki-Page with instructions.

See http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page

It's working, awesome! Thanks a lot for the great job!
Title: Re: *experimental* wireless usb support package
Post by: realtebo on May 07, 2009, 09:13:05 AM
I can add this product: the Nintendo Wii usb to lan adapter (here from San Marino (http://www.hardstore.com/default.asp?cmd=getProd&cmdID=8287) at only 21€ !!!)

This model uses the ASIX 88772 and go very very well. It's USB 2.0 and work at 10 or 100 Megabit
Title: Re: *experimental* wireless usb support package
Post by: FVD on May 07, 2009, 08:00:44 PM
Hi,

I am trying to connect a TL-WN322G which happens to have a identification of ZD1211B  [0ace:1215] , but without any succes i have been trying the following configuration
Quote
Jan  1 00:02:02 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:02:03 (none) user.warn kernel: zd1201: Unknown symbol release_firmware
Jan  1 00:02:03 (none) user.warn kernel: zd1201: Unknown symbol request_firmware
Jan  1 00:02:05 (none) user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:02:05 (none) user.notice kernel: vendor_id = 0ace
Jan  1 00:02:05 (none) user.notice kernel: product_id = 1215
Jan  1 00:02:05 (none) user.notice kernel: USB 2.0 Host
Jan  1 00:02:05 (none) user.notice kernel: Release Ver = 4810
Jan  1 00:02:05 (none) user.notice kernel: EEPROM Ver = 4810
Jan  1 00:02:05 (none) user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:02:05 (none) user.err kernel: PA type: 0
Jan  1 00:02:05 (none) user.warn kernel: AR2124 RF
Jan  1 00:02:05 (none) user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:02:06 (none) user.debug kernel: OverWrite CR157 = 0xF0
Jan  1 00:02:06 (none) user.debug kernel: zd1205_config: EEP(HWFeature)=0x2000
Jan  1 00:02:06 (none) user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:02:06 (none) user.warn kernel: Region:48
Jan  1 00:02:06 (none) user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:02:06 (none) user.notice root: net.agent:  Called for eth0
Jan  1 00:02:10 (none) user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:02:10 (none) user.info kernel: usbcore: registered new driver Otus
Jan  1 00:02:11 (none) user.warn kernel: rtusb init --->
Jan  1 00:02:11 (none) user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:02:11 (none) user.info kernel: usbcore: registered new driver rt73
Jan  1 00:02:14 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:02:14 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:02:26 (none) user.debug kernel: RadioOn
Jan  1 00:02:26 (none) user.notice root: Testing static IP assignment...
Jan  1 00:02:27 (none) user.info kernel: NTFS volume version 3.1.
Jan  1 00:02:41 (none) user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:02:41 (none) user.notice root: IP Assignment failed.  Trying DHCP
Jan  1 00:02:55 (none) daemon.notice ntfs-3g[3141]: Version 2009.4.4 integrated FUSE 27
Jan  1 00:02:55 (none) daemon.notice ntfs-3g[3141]: Mounted /dev/sdc2 (Read-Write, label "My Book", NTFS 3.1)
Jan  1 00:02:55 (none) daemon.notice ntfs-3g[3141]: Cmdline options: force
Jan  1 00:02:55 (none) daemon.notice ntfs-3g[3141]: Mount options: force,silent,allow_other,nonempty,relatime,fsname=/dev/sdc2
Jan  1 00:03:15 (none) user.err kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

this correspond to message.txt

below what appears in system.txt

Quote
/dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
/dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
/dev/sda1: UUID="5034-81AA" TYPE="vfat"
/dev/sdb1: SEC_TYPE="msdos" LABEL="SWISSMEMORY" UUID="66D2-ED2D" TYPE="vfat"
/dev/loop0: LABEL="log-saver" TYPE="cramfs"
/dev/loop1: LABEL="wmod-003" TYPE="cramfs"
/dev/sr0: LABEL="SLUMDOG_MILLIONAIRE_NTSC_DVDR_SC" TYPE="udf"
======================================
Displaying detected USB devices...
 [1307:0165] 1-1( 2.00,480m) USB Flash Drive/df71faf067040b
 [05e3:0608] 1-2( 2.00,480m) USB2.0 Hub
 [0ace:1215] 1-2.1( 2.00,480m) USB2.0 WLAN
 [1370:0321] 1-2.2( 2.00,480m) Victorinox 2.0/10006126B4000321
 [0ecd:a100] 1-2.3( 2.00,480m) Mass Storage Device/DEF1087225CF
 [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
 [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
======================================
major minor  #blocks  name

   7     0          4 loop0
   7     1       2364 loop1
  31     0      16384 mtdblock0
  31     1        384 mtdblock1
  31     2       2176 mtdblock2
  31     3      13568 mtdblock3
  31     4        128 mtdblock4
  31     5        128 mtdblock5
   8     0    7897088 sda
   8     1    7897056 sda1
   8    16    2031104 sdb
   8    17    2031088 sdb1
======================================
rootfs / rootfs rw 0 0
proc /proc proc rw,nodiratime 0 0
sysfs /sys sysfs rw 0 0
/dev/mtdblock3 / cramfs ro 0 0
none /proc proc rw,nodiratime 0 0
usb /proc/bus/usb usbfs rw 0 0
sysfs /sys sysfs rw 0 0
none /tmp tmpfs rw 0 0
none /etc/mdev.conf tmpfs rw 0 0
mdev /dev tmpfs rw 0 0
devpts /dev/pts devpts rw 0 0
/dev/sdb1 /tmp/mnt/sdb1 vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
/dev/loop0 /tmp/mnt/apps/log-saver cramfs ro 0 0
/dev/loop1 /tmp/mnt/apps/wireless-mod cramfs ro 0 0
none /osd/image/welcome_background_bg.jpg tmpfs rw 0 0
none /osd/image/screen_saver.png tmpfs rw 0 0
/dev/sr0 /tmp/media/usb/SLUMDOG_MILLIONAIRE_NTSC_DVDR_SC udf ro 0 0
none /osd/setup_about.xml tmpfs rw 0 0
/dev/sdb1 /tmp/media/usb/USB2/66D2-ED2D vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
/dev/sda1 /tmp/media/usb/USB1/5034-81AA vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=utf8 0 0
none /osd/setup_about.xml tmpfs rw 0 0
======================================

and finally this is what i had been using for net.config and wpa
Quote
#
# Network configuration file
#You can override the hostname here:


ifconfig eth0 up channel 6 > /boot/logba.txt

sleep 2

iwconfig eth0 essid VIENNA > /boot/logb.txt


sleep 2
#wpa_supplicant -Bw -Dotus -i$MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf > /boot/log.txt
wpa_supplicant -Bw -Dwext -ieth0 -c /boot/wpa_supplicant.conf > /boot/log.txt

sleep 5

HOST=wdtv
MTU=9000

DHCP=no
IP=192.168.0.110
GW=192.168.0.1
DNS1=192.168.0.1

sleep 5


and wpa_suplicant.conf
Quote
# WPA-PSK/TKIP

ctrl_interface=/tmp/wpa_supplicant
network={
   ssid="VIENNA"
   scan_ssid=1
   proto=WPA
   key_mgmt=WPA-PSK
   #pairwise=TKIP
   group=TKIP
   psk="GF15335784512"
}
# WPA-PSK/TKIP

IN VISTA THE DONG USE THE ATHEROS DRIVER FOR AR5007G

ANY HELP WILL BE APPRECIATED


AHHH ONE MORE QUESTION WHY I DON´T RECEIVE ANY ANSWER OR LOG FROM IFCONFIG OR IWCONFIG AFTER I USE > /BOOT/LOG.TXT


THX IN ADVANCE
Title: Re: *experimental* wireless usb support package
Post by: mx5gr on May 08, 2009, 07:46:27 AM

For the DWA-140 (or any rt2870-based thing), I've updated the Wiki-Page with instructions.

See http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page

It does not work with Linksys D600N-USB. After showing the WD screen, the device turns on the USB LED and freezes with black screen.

Can someone send net.config to double check ?

messages.txt:
Code: [Select]
Jan  1 00:00:34 (none) syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:34 (none) user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:34 (none) user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:34 (none) user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:34 (none) user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:34 (none) user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:34 (none) user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:34 (none) user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:34 (none) user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:34 (none) user.warn kernel: Determined physical RAM map:
Jan  1 00:00:34 (none) user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:34 (none) user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:34 (none) user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:34 (none) user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:34 (none) user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:34 (none) user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:34 (none) user.warn kernel: Built 1 zonelists
Jan  1 00:00:34 (none) user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:34 (none) user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:34 (none) user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:34 (none) user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:34 (none) user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:34 (none) user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:34 (none) user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:34 (none) user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:34 (none) user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:34 (none) user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:34 (none) user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:34 (none) user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:34 (none) user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:34 (none) user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:34 (none) user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:34 (none) user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:34 (none) user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:34 (none) user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:34 (none) user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:34 (none) user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:34 (none) user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:34 (none) user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:34 (none) user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:34 (none) user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:34 (none) user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:34 (none) user.notice root: 1.02.07.WDLXTV-0.5.2
Jan  1 00:00:34 (none) user.notice root: Displaying detected USB devices...
Jan  1 00:00:34 (none) user.notice root:  [0951:160f] 1-1( 2.00,480m) DT Mini Slim/0019E06B7106A9215798079E
Jan  1 00:00:35 (none) user.notice root:  [1737:0071] 1-2( 2.00,480m) Dual-Band Wireless-N USB Network Adapter
Jan  1 00:00:35 (none) user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:35 (none) user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:34 (none) user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:36 (none) user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:36 (none) user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:36 (none) user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:36 (none) user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:36 (none) user.info kernel: Initializing Cryptographic API
Jan  1 00:00:36 (none) user.info kernel: io scheduler noop registered
Jan  1 00:00:36 (none) user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:36 (none) user.info kernel: io scheduler deadline registered
Jan  1 00:00:36 (none) user.info kernel: io scheduler cfq registered
Jan  1 00:00:36 (none) user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:36 (none) user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:36 (none) user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:36 (none) user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:36 (none) user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:36 (none) user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:36 (none) user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:36 (none) user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:36 (none) user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:36 (none) user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:36 (none) user.notice kernel: number of CFI chips: 1
Jan  1 00:00:36 (none) user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:36 (none) user.notice kernel: Using physmap partition definition
Jan  1 00:00:36 (none) user.notice kernel: Adding partition #1-#5
Jan  1 00:00:36 (none) user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:36 (none) user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:36 (none) user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:36 (none) user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:36 (none) user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:36 (none) user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:36 (none) user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:36 (none) user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:36 (none) user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:36 (none) user.warn kernel: TangoX USB initializing...
Jan  1 00:00:36 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:36 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:36 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:36 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:36 (none) user.info kernel: hub 1-0:1.0: USB hub fou
Jan  1 00:00:36 (none) user.info kernel: nd
Jan  1 00:00:36 (none) user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:36 (none) user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:36 (none) user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:36 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:36 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:36 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:36 (none) user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:36 (none) user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:36 (none) user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:36 (none) user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:36 (none) user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:36 (none) user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:36 (none) user.debug kernel: usb-storage: device found at 2
Jan  1 00:00:36 (none) user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:36 (none) user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:36 (none) user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:36 (none) user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:36 (none) user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:36 (none) user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:36 (none) user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:36 (none) user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:36 (none) user.info kernel: TCP reno registered
Jan  1 00:00:36 (none) user.info kernel: TCP bic registered
Jan  1 00:00:36 (none) user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:36 (none) user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:36 (none) user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:36 (none) user.notice kernel:   Vendor: Kingston  Model: DT Mini Slim      Rev: 1.00
Jan  1 00:00:36 (none) user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
Jan  1 00:00:36 (none) user.notice kernel: SCSI device sda: 15761408 512-byte hdwr sectors (8070 MB)
Jan  1 00:00:36 (none) user.notice kernel: sda: Write Protect is off
Jan  1 00:00:36 (none) user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:36 (none) user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:36 (none) user.notice kernel: SCSI device sda: 15761408 512-byte hdwr sectors (8070 MB)
Jan  1 00:00:36 (none) user.notice kernel: sda: Write Protect is off
Jan  1 00:00:36 (none) user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:36 (none) user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:36 (none) user.info kernel:  sda: sda1
Jan  1 00:00:36 (none) user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:36 (none) user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:36 (none) user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:36 (none) daemon.info utelnetd[320]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:00:46 (none) user.notice root: crazymounter: mounting devices
Jan  1 00:00:46 (none) user.notice root: /dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
Jan  1 00:00:46 (none) user.notice root: /dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
Jan  1 00:00:46 (none) user.notice root: /dev/sda1: LABEL="KINGSTON" UUID="3433-3231" TYPE="vfat"
Jan  1 00:00:47 (none) user.notice root: /dev/sda1: LABEL="KINGSTON" UUID="3433-3231" TYPE="vfat"
Jan  1 00:00:47 (none) user.notice root: xmount.scan: Will not mount /dev/sda1 (vfat)
Jan  1 00:00:47 (none) user.notice root: crazymount: mounting app binaries...
Jan  1 00:00:48 (none) user.notice root: DEVICE /dev/sda1 CONNECTED
Jan  1 00:00:48 (none) user.notice root: log-saver app found
Jan  1 00:00:48 (none) user.notice root: Mounting /tmp/mnt/sda1/log-saver.app.bin at /tmp/mnt/apps/log-saver
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=68, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=1252, limit=8
Jan  1 00:00:48 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:48 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:48 (none) user.warn kernel: UDF-fs: No partition found (1)
Jan  1 00:00:49 (none) user.notice root: Mounting opt.bin at /opt
Jan  1 00:00:49 (none) user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:49 (none) user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:00:49 (none) user.warn kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jan  1 00:00:49 (none) user.info kernel: EXT3 FS on loop1,
Jan  1 00:00:49 (none) user.info kernel: internal journal
Jan  1 00:00:49 (none) user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:00:49 (none) user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:00:49 (none) user.notice root: wireless-mod-seb app found
Jan  1 00:00:49 (none) user.notice root: Mounting /tmp/mnt/sda1/wireless-mod-seb.app.bin at /tmp/mnt/apps/wireless-mod-seb
Jan  1 00:00:49 (none) user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:52 (none) user.notice root: adjusting LIBPATH
Jan  1 00:00:53 (none) user.notice root: adjusting PATH
Jan  1 00:00:53 (none) user.notice root: Path set to /opt/sbin:/opt/bin:/apps/wireless-mod-seb/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:56 (none) user.notice root: Inserting the modules...
Jan  1 00:00:56 (none) user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:56 (none) user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:57 (none) user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:01:03 (none) user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:01:03 (none) user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
Jan  1 00:01:03 (none) user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:01:04 (none) user.notice root: Generated new defaultHOST=WDTV-052a1
Jan  1 00:01:08 (none) user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:08 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:01:09 (none) user.warn kernel: rtusb init --->
Jan  1 00:01:09 (none) user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:09 (none) user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:09 (none) user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:10 (none) user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:10 (none) user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:10 (none) user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:10 (none) user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:10 (none) user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:10 (none) user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:10 (none) user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:11 (none) user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:11 (none) user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:11 (none) user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:11 (none) user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:13 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:13 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Title: Siemens Gigaset USB Adapter 108
Post by: ginolo on May 08, 2009, 07:56:40 AM
Greetings!

first a big thanks to all who work so hard in making this little and powerful device even more powerful!

I'm trying to get my Siemens Gigaset USB Adapter 108 (message.txt shows this as [129b:160c] AR5523/1.0) to work. It seems the driver is not being loaded for this one (no lookup defined for the two IDs?).

I've tried b-rad's and Zorander's firmware with both wireless-mod.app.bin and wireless-mod-wdlxtv.app.bin without any success.
What can I do to get this working without having to buy more hardware?

Any links/hints/pointers are very much appreciated.

-g

PS: from http://forum.freespire.org/showthread.php?t=3939
* Chipset : Atheros 5523
* usbid: 129b:160b
* Drivers: athfmwdl + net5523 (both needed) from CD provided with device
Title: Re: *experimental* wireless usb support package
Post by: marcob on May 10, 2009, 04:03:07 AM
Hi everybody
sorry for my poor english
I'm trying to connect my wdtv using a usb wireless pen (Linksys WUSB54GC)
but nothing works.
I tried the simplest configuration with no security/encryption, access to everyone
, ssid brodcast enabled and I used this net.config:
Quote
ifconfig eth0 up channel 6
sleep 2
iwconfig eth0 essid MY-SSID-NAME
sleep 5
HOST=wdtv
#MTU=9000
DHCP=yes
#IP=192.168.0.110
#GW=192.168.0.1
#DNS1=192.168.0.1
sleep 5
But there is no way to connect my wdtv to my wireless router.
I can see the led of the usb pen is blinking, but the wdtv still
shows me "No Ip Address".
So what do you suggest?
I found that the Linksys WUSB54GC uses Ralink RT2501USB chipset
(http://www.decimation.com/markw/2007/12/04/wusb54gc-and-vista/)
and also I found the linux drivers here :http://www.ralinktech.com/ralink/Home/Support/Linux.html
but I'm not an expert of linux and I don't know what to do.
thank for your help.
Marco.
Title: Re: *experimental* wireless usb support package
Post by: fozzieb on May 10, 2009, 07:54:44 AM
iwconfig eth0 essid MY-SSID-NAME

the MY-SSID-NAME should be the routers wireless name, that you want to connect to.

By default these are the make of the router - BELKIN NETGEAR DLINK, if you do not know it log in to router and check it in settings or if your pc connects over wifi see what it connects to.

Cheers
Title: Re: *experimental* wireless usb support package
Post by: marcob on May 10, 2009, 08:58:01 AM
I write MY-SSID-NAME just to make an example.
Title: Re: *experimental* wireless usb support package
Post by: fozzieb on May 10, 2009, 09:28:16 AM
herre is my net.config

Code: [Select]
HOST=wdtv

ifconfig $MDEV up
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf

DHCP=yes

and my wpa_supplicant.conf

Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="SSID"
key_mgmt=WPA-PSK
psk="PASSWORD"
}

I have a DWA-111

Not sure if any of that helps.
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 10, 2009, 12:15:37 PM
Hi,
Can someone clarify me (after reading 19 pages of this subject) if wdtv wireless works in may case or not?

I have a SMCWUSB-D which I believe has the zd1211b chipset which is the one you say it most probably work...
At first I was happy with my luck...

However now I'm beggining to feel said, because I didn't have success.

What I did was:

installed b-rad WDLXTV version 0.5.2 firmware

copied the experimental wireless-mod.app.bin from zorander (don't know the exact version because all versions seems to be
equal and with the same size 2.420.736 bytes)

edited net.config to this:
ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

edited wpa_supplicant.conf to this:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="belkin54g"
# uncomment next line if your ap doesn't broadcast ssid
# scan_ssid=1
key_mgmt=WPA-PSK
psk="password"
}

The lights of my dongle flashes but I cannot get an IP

Any ideas? I did several combinations like uncomment scan_ssid=1 but without success.
I also don't know if I have to mantain or not the quotes in wpa_supplicant.conf

I guess wireless-mod.app.bin from zorander does not work with WDLXTV version 0.5.2 firmware, because
B-RAD says in his front page that:
Experimental wireless adapter support (thx to Zorander) (requires wireless-mod-wdlxtv app pack)

and wireless-mod-wdlxtv is missing from his page so I assume he is still working on it, but then I don't understand how some people is able to connect wireless!!

Please someone to elucidade me

Best regards
Title: Re: *experimental* wireless usb support package
Post by: fozzieb on May 10, 2009, 12:37:38 PM
I could not get mine working with wdlxtv but woked first time with ext3-boot-0.9.2.
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 10, 2009, 12:51:23 PM
Hi

How to roll back firmware?

I know I have to change wdtv.ver but I cannot enter the page where that is explained and without that wdtv
does not see 0.9.2 as a new firmware...

Did you use the same net.config and wpa_supplicant.conf as me?

your wireless-mod.app.bin has also 2.420.736 bytes bytes?

Thanks a lot
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 10, 2009, 01:59:13 PM
I was able to roll back

But still no luck with 0.9.2

The messages give this over and over and over and the light is always flashing...

ANY HINTS?

.
.
.
 ZD1211B - version 2.19.2.9
Jan  1 00:00:38 wdtv user.notice kernel: vendor_id = 083a
Jan  1 00:00:38 wdtv user.notice kernel: product_id = 4505
Jan  1 00:00:38 wdtv user.notice kernel: USB 2.0 Host
Jan  1 00:00:38 wdtv user.notice kernel: Release Ver = 4810
Jan  1 00:00:38 wdtv user.notice kernel: EEPROM Ver = 4810
Jan  1 00:00:38 wdtv user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:00:38 wdtv user.err kernel: PA type: 0
Jan  1 00:00:38 wdtv user.warn kernel: PHYNEWLayout = 1
Jan  1 00:00:38 wdtv user.warn kernel: AiroHa AL2230RF
Jan  1 00:00:38 wdtv user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:00:38 wdtv user.debug kernel: OverWrite CR47 = 0x1C
Jan  1 00:00:38 wdtv user.debug kernel: zd1205_config: EEP(HWFeature)=0x500
Jan  1 00:00:38 wdtv user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:00:38 wdtv user.warn kernel: Region:16
Jan  1 00:00:39 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:39 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:00:39 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:40 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:40 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:40 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:41 wdtv user.debug kernel: keybuf data
Jan  1 00:00:41 wdtv user.debug kernel:
Jan  1 00:00:41 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:41 wdtv user.debug kernel: keybuf data
Jan  1 00:00:41 wdtv user.debug kernel:
Jan  1 00:00:41 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:41 wdtv user.debug kernel: keybuf data
Jan  1 00:00:41 wdtv user.debug kernel:
Jan  1 00:00:41 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:41 wdtv user.debug kernel: keybuf data
Jan  1 00:00:41 wdtv user.debug kernel:
Jan  1 00:00:41 wdtv user.debug kernel: Just Update WEP key
Jan  1 00:00:41 wdtv user.debug kernel: keybuf data
Jan  1 00:00:41 wdtv user.debug kernel:
Jan  1 00:00:41 wdtv user.debug kernel: Update CardSetting
Jan  1 00:00:41 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:41 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:41 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:41 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:42 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0
Jan  1 00:00:42 wdtv user.warn kernel: What~~~~PS_POLL & mPwrState ==0

.
.
.
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 10, 2009, 11:25:42 PM
Hi everybody
sorry for my poor english
I'm trying to connect my wdtv using a usb wireless pen (Linksys WUSB54GC)
but nothing works.
I tried the simplest configuration with no security/encryption, access to everyone
, ssid brodcast enabled and I used this net.config:
Quote
ifconfig eth0 up channel 6
sleep 2
iwconfig eth0 essid MY-SSID-NAME
sleep 5
HOST=wdtv
#MTU=9000
DHCP=yes
#IP=192.168.0.110
#GW=192.168.0.1
#DNS1=192.168.0.1
sleep 5
But there is no way to connect my wdtv to my wireless router.
I can see the led of the usb pen is blinking, but the wdtv still
shows me "No Ip Address".
So what do you suggest?
I found that the Linksys WUSB54GC uses Ralink RT2501USB chipset
(http://www.decimation.com/markw/2007/12/04/wusb54gc-and-vista/)
and also I found the linux drivers here :http://www.ralinktech.com/ralink/Home/Support/Linux.html
but I'm not an expert of linux and I don't know what to do.
thank for your help.
Marco.
Post messages.txt file.
Title: Re: *experimental* wireless usb support package
Post by: Kater432 on May 11, 2009, 12:58:11 AM
edited net.config to this:
ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

Try it with "-D otus"
My dongle is also a zd1211b and the wpa_supplicant or the driver dont make wpa with -Dwext

Kater432
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 11, 2009, 04:29:01 AM
It works!!

You are the one!!

Thanks!!

But now I wanted to use tversity which streams well to the ps3 but wdtv does not show anything in the upnp folder.

My signal is weak in the bedroom. I will try later in the living room.

And maybe it's better to try to configure nfs

All the best
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 11, 2009, 10:47:05 AM
Hi everybody
sorry for my poor english
I'm trying to connect my wdtv using a usb wireless pen (Linksys WUSB54GC)
but nothing works.
I tried the simplest configuration with no security/encryption, access to everyone
, ssid brodcast enabled and I used this net.config:
Quote
ifconfig eth0 up channel 6
sleep 2
iwconfig eth0 essid MY-SSID-NAME
sleep 5
HOST=wdtv
#MTU=9000
DHCP=yes
#IP=192.168.0.110
#GW=192.168.0.1
#DNS1=192.168.0.1
sleep 5
But there is no way to connect my wdtv to my wireless router.
I can see the led of the usb pen is blinking, but the wdtv still
shows me "No Ip Address".
So what do you suggest?
I found that the Linksys WUSB54GC uses Ralink RT2501USB chipset
(http://www.decimation.com/markw/2007/12/04/wusb54gc-and-vista/)
and also I found the linux drivers here :http://www.ralinktech.com/ralink/Home/Support/Linux.html
but I'm not an expert of linux and I don't know what to do.
thank for your help.
Marco.

I have that same model. The driver is rt73, and is already included in wireless-mod.app.bin, no need to download or compile aditional drivers.
It works OK with or without encryption, including WEP,WPA and WPA2.

The first thing you have to do is change eth0 to $MDEV in both ifconfig and iwconfig lines. (I think the device name is rausb0, but with $MDEV you ensure it's OK). I don't know if channel option is working (try without especifying it first).
You should check the wiki http://wiki.wdtv.org (http://wiki.wdtv.org), for the Ralink rt73 wireless adapters.
Title: Re: *experimental* wireless usb support package
Post by: marcob on May 12, 2009, 11:33:49 PM
great mike2k8 ... thats work!
I done exactly as you said and now my wdtv is connected to my
wireless network.
thanks a lot.
well ... now I'm having trouble with the ssid, I setup a "not broadcasted ssid"
in my router, and I used the wps_supplicant.config to connect to it,
but it doesn't work .
these are the net.config and wps_supplicant.config I used:
net.config
Code: [Select]
ifconfig $MDEV up
sleep 2
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
sleep 5
HOST=wdtv
#MTU=9000
DHCP=yes
#IP=192.168.0.110
#GW=192.168.0.1
#DNS1=192.168.0.1
sleep 5
wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="my-ssid"
key_mgmt=NONE
scan_ssid=1
}
Title: Re: *experimental* wireless usb support package
Post by: smartP on May 13, 2009, 04:51:00 AM
well ... now I'm having trouble with the ssid, I setup a "not broadcasted ssid"

for hidden ssids you'll need to add ap_scan=2 to your wpa_supplicant.conf

ie.
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
ap_scan=2
network={
ssid="my-ssid"
key_mgmt=NONE
scan_ssid=1
}
Title: Re: *experimental* wireless usb support package
Post by: yakirdvir on May 13, 2009, 05:00:00 AM
its support rtl8187 chipsets?
Title: Re: *experimental* wireless usb support package
Post by: smartP on May 13, 2009, 05:27:39 AM
I've been trying to understand and fix an intermittent problem with my wireless setup and have finally found a 99% reliable way of getting the wireless to connect.

I'm using ext3-0.9.2 and have the following files on the usb:
http://www.mediafire.com/file/wmyw0zdz1dm/rt2870sta.zip

Note: this method does not require any *.app.bin

Just edit the /etc/RT2870STA.dat and uncomment the 4 lines starting with #SSID
or edit the wpa_supplicant.conf with your wireless details.

One last addition note for fellow dev/hackers - be careful of what you put in the net.config as it is sourced/executed 3 times!
Once on startup, again by /etc/init.d/S20netmodules.sh, and lastly by /etc/hotplug/net.agent.
Title: Re: *experimental* wireless usb support package
Post by: marcob on May 13, 2009, 11:04:43 AM
unfortunatly there is nothing to do with "no ssid broadcasting". I added ap_scan=2 parameter to the wpa_supplicant file but it still doesn't work.
attached there are the log files,
this is the wpa_supplicant.conf file:
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
ap_scan=2
network={
ssid="my-ssid"
key_mgmt=NONE
scan_ssid=1
}
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 15, 2009, 05:00:10 AM
Hm, i have a linksys wusb600n (also rt2170) and tried the dwa-140 tutorial, but it doesnt work. The led light shows no reaction on startup and so there is no IP. At the moment i use b-rads wdlxtv firmware.

@smartP
What RT2870 device do you have?
Title: Re: *experimental* wireless usb support package
Post by: wdtv101 on May 15, 2009, 05:53:28 AM
Hm, i have a linksys wusb600n (also rt2170) and tried the dwa-140 tutorial, but it doesnt work. The led light shows no reaction on startup and so there is no IP. At the moment i use b-rads wdlxtv firmware.

@smartP
What RT2870 device do you have?

I have LinkSys WUSB600N...  I used wireless-mod-wdlxtv.app.bin-rt2870... It works with latest firmware WDLXTV-0.5.3.2 too...

Quote from: RT2870STA
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
ChannelGeography=1
SSID=----YourWirelessRouterSSID----
NetworkType=Infra
WirelessMode=8
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
PktAggregate=0
WmmCapable=1
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=AES
WPAPSK=----YourWirelessRouterNetworkKey----

PSMode=CAM
AutoRoaming=0
RoamThreshold=70
APSDCapable=0
APSDAC=0;0;0;0
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_BADecline=0
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
HT_DisallowTKIP=1
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0
AntDiversity=0
BeaconLostTime=4

Quote from: net.config
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional: 

#specify time server host
#NTP=pool.ntp.org

#specify timezone
#TZ=PST8EDT


[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
ifconfig rausb0 up
udhcpc -H wdtv -i rausb0


==================================================
For anyone with a WLAN using rt2870, REJOICE!!

I've just managed to get it all working on my WDTV and it's fricking AWESOME!

OK to get it to work....

1. Download the following package: wireless-mod-wdlxtv.app.bin-rt2870.zip (http://www.mediafire.com/download.php?ylmw2tzmiyn (http://www.mediafire.com/download.php?ylmw2tzmiyn))
Hope b-rad doesn't mind me updating his file.   :-\

2. Unzip to the root of your usb with existing WDLXTV-0.4.X files. You should have 2 new files, wireless-mod-wdlxtv.app.bin and RT2870STA.dat

3. Edit the RTA2870STA.dat with your wireless config, using README_STA as a reference. (http://www.mediafire.com/download.php?y4ty3qzqxjz (http://www.mediafire.com/download.php?y4ty3qzqxjz))

4. Edit net.config and add the following lines at the bottom:

[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
ifconfig rausb0 up
udhcpc -H wdtv -i rausb0


5. Done. Reboot!!!

btw: driver version is 2.1.0.0

http://wdtvforum.com/main/index.php?topic=59.150
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 15, 2009, 07:32:40 AM
Bix thx. That should be added in the wiki wlan-howto.

Now the Stick react and blink some seconds then pause and blink again, so the driver work but it never turn into green the whole time. So something isn't right atm. I tried the 2.1.0.0 under Ubuntu 8.10 some weeks ago and had many problems (wlan found, wpa2psk detected, but key not accepted although it was correct). The old 1.4.0.0 driver worked then. Dunno if this is the same problem. But you said, that it worked for you. So there must be another mistake. net.config and RT2870STA are exactly like yours with SSID and wpapsk key added.
I use wpa2psk, ssid broadcast is on, encryption aes.

Where can i find the message.txt? There's nothing on the drive.

edit:

OK, i made progress.

First of all I checked all entries of RT2870STA and changed some.

Quote from: RT2870STA CHANGES
CountryRegion=1 #for Germany -> 1-13
CountryCode="" #for channel 1-11
WirelessMode=9 #i use BGN here - dunno whether N doesnt work correctly
Channel=1 #channel is "auto" and the router uses channel 1

And the stick is green now. The router shows "wdtv" in the DHCP list. But i cant ping or use telnet with the unit. WDLX shows also "No IP" at startup (although it has an IP).
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 15, 2009, 12:16:40 PM
I had success to go wireless with zd1211b chipset and zorander 's wireless bin (2.3 Mb bin) but the performance is poor.

However with c-rad new wireless bin (10 Mb) and new 0.5.3.2 the dongle doesn't blink and I don' have IP.
Did someone have success?
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 15, 2009, 02:07:52 PM
Explaining better my last post...

B-rad 13th  of May wirelessmod bin doesn’t give me IP with zd1211b chipset and wdxltv 0.5.3.2
The light is always green and it never blinks, so I assume the driver is not working.
zorander wirelessmod 0.3 (much smaller file) works with B-rad 0.5.3.2 but only if not using WPA or WPE.
However UPnP doesn’t work with tversity (there must be a bug with B-rad UPnP bin too…)
zorander ext-boot 0.9.2 and zorander wireless 0.3 works well and Tversity UpnP also works, but the performance is very poor.
FLAC files are freezing and I didn’t try 1080p or 720p
I have to try this dongle in a pc with linux to see if it plays the FLACS without freezing.

Any ideas?
Title: Re: *experimental* wireless usb support package
Post by: wdtv101 on May 15, 2009, 09:55:23 PM
And the stick is green now. The router shows "wdtv" in the DHCP list. But i cant ping or use telnet with the unit. WDLX shows also "No IP" at startup (although it has an IP).
Yes, it does show "No IP" at startup...

Wait for a minute or two, go to the "Settings - System - About".  If you see the "About" displays an IP address then WDTV connect to the router...  Now you can ping, telnet to that IP...
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 16, 2009, 02:23:40 AM
Hm, now it works. Changed the net.config a little bit, because some people reported a "bug" with DHCP (set to no, but still used it). And the new order makes more sense

Quote from: net.config
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
#MTU=9000

#
# Dynamic IP Configuration:

#DHCP=yes

#
# Optional:

#specify time server host
#NTP=pool.ntp.org

#specify timezone
#TZ=PST8EDT

[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
ifconfig ra0 up

udhcpc -H wdtv -i ra0

The name of the interface isn't rausb0. It's ra0. Nevertheless the interface also came up before and i could connect, dunno why (but with dhcp problems, static ip worked better). But then I saw the real interface name and changed it. Now with the correct name the startup seems little bit faster, dhcp works and the ip show up at the startup.

Telnet and the other things works fine now. I installed optware and play with some tools. Wlan and the other stuff are a nice feature. Dunno why WD build a second version of the WD TV. The first version already has everything. They just have to implement more things like driver-support for usb-lan and usb-wlan adapters etc.
Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 16, 2009, 02:42:11 AM
I don' know how you guys have success with the 10 Mb filesize wireless bin from B-rad.

For me the wireless_ext just does not load any wireless modules!! Not your modules nor my modules (zd1211b)

I saw this in the messages.txt left at the dongle.

A little bit confused...
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 16, 2009, 03:50:07 AM
Hm, my speed is totally crap. I have a 32mbit connection and use wlan n. Iwconfig shows me 270-300mbit and full link quality (100/100 - only 5m to the router), so that should be ok. But i got only 100-250KB/sec from the web and my network (download via ftp from my pc).

I've installed nzbget with web-interface and with 8 connections I also get only 200-250KB/sec. But my connection reachs up to 3,65MB/sec. The Download is written on the external 2,5" hdd on the fat32 partition. Any hints?
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 16, 2009, 04:00:41 AM
I didn't test Fat32 write speed, but NTFS write speed is very low (about 250KB/s). Try writing to an ext3 partitions (write speed is about 3.2 MB/s).
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 16, 2009, 04:29:55 AM
Aaaahhhh, my fault, thanks for the hint. I thought it was fat32, but now I saw at mount, that it's ntfs. That is my first partition, where i have all the bin's and updated the firmware from that drive. I just thought that only the second partition with the media files has ntfs. Puh. :-)

Then it's clear. Because ntfs-support under linux is not the best (for write). I think fat32 should have the same performance like ext3.
Title: Re: *experimental* wireless usb support package
Post by: xurde on May 16, 2009, 10:37:16 AM
Hi,

I have a Dlink DWL-G122 rev C1. My firmware is WDLXTV 0.5.2. I've just read in the previous messages that some of you are trying to work with this combination, but for me is impossible (I've got the same results as Civuck, the LEDs flash every 5 seconds or so but no IP is listed in the About screen). Any of you have a way to solve this?

Thanks in advance!

Title: Re: *experimental* wireless usb support package
Post by: johnnypeste on May 16, 2009, 01:07:32 PM
If it blinks then most certainly it's a wpa problem. Try -Dotus or the other 2 options. See page 20 of this post (before this one...) If it doesn't work try WPE or unsecured for a few minutes just to be sure.

If you are using 0.5.2 and wireless-wdxltv then you are lucky because I have to use wireless 0.3 from zorander and ext3-boot to have a connection with poor performance.
Title: Re: *experimental* wireless usb support package
Post by: Civuck on May 16, 2009, 09:28:12 PM

I have a Dlink DWL-G122 rev C1. My firmware is WDLXTV 0.5.2. I've just read in the previous messages that some of you are trying to work with this combination, but for me is impossible (I've got the same results as Civuck, the LEDs flash every 5 seconds or so but no IP is listed in the About screen).
I'm about ready to send up the white flag with my Dlink DWL-G122 and just get a USB Ethernet adapter.  I suspect the performance will be worth it over wireless anyway.  The Apple USB adapter looks good.
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 17, 2009, 02:34:17 AM
Hi,

I have a Dlink DWL-G122 rev C1. My firmware is WDLXTV 0.5.2. I've just read in the previous messages that some of you are trying to work with this combination, but for me is impossible (I've got the same results as Civuck, the LEDs flash every 5 seconds or so but no IP is listed in the About screen). Any of you have a way to solve this?

Thanks in advance!
I've the same wifi adpter.
This configuration file should work with or without dhcp.
net.config
Code: [Select]
HOST=wdtv
DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.1.65
#GW=192.168.1.1
#NM=255.255.255.0
#DNS1=212.216.112.222
#DNS2=212.216.172.62
wpa_supplicant.conf:
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your_ssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="type_your_key_here"
}

For this command:

wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

I don't know if path /boot/wpa_supplicant.conf is right for WDLXTV ;) It works fine on ext3-boot.
If it won't work again, try adding sleep 5 at the end of net.config.
Title: Re: *experimental* wireless usb support package
Post by: xurde on May 17, 2009, 05:08:35 AM
It's working with ext3-boot using cionci conf  ;D. No results with WDLXTV  :( (eveng using WEP or not restricted access).

Thanks guys.
Title: Re: *experimental* wireless usb support package
Post by: cionci on May 17, 2009, 08:55:12 AM
For ext3-boot you must add sleep 5 at the end ;) I wasn't able to use both rt73 I own with WEP or open networks.
As I said before, I don't know where partition on which you have wireless-mod.app.bin is mounted in WDLXTV. wpa_supplicant command points directly to /boot/wpa_supplicant.conf, this is correct with ext3-boot, but for WDLXTV you may need to change path to conf file.
Title: Re: *experimental* wireless usb support package
Post by: videomilk on May 19, 2009, 07:21:18 PM
Hi,  I was wondering if there was any progress on the drivers for the Ralink rt2570 adapters.  If not I might bite the bullet and buy one of the RT73's?

Thanks
Title: Re: *experimental* wireless usb support package
Post by: pacorob on May 20, 2009, 05:23:01 AM

I have LinkSys WUSB600N...  I used wireless-mod-wdlxtv.app.bin-rt2870... It works with latest firmware WDLXTV-0.5.3.2 too...


Can wdtv101 (or someone else :)) help me out. I just bought my linksys wusb600n a few days ago and tried to figure it out to get wireless network going but it doesn't seem to work (no ip at About page) and no network harddisk share although I shared one hd in the network. Should I change anything else on the wusb600n usb via a pc? How does the Linksys wusb600n know that my sony usb stick has the network key? Or does wdxltv looks for that automaticly?

I have used wdtv101 settings: http://wdtvforum.com/main/index.php?topic=59.msg5341#msg5341 and read these instructions: http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page

I use 1.02.07_B-RAD.CC_WDLXTV-0.5.2 firmware that works fine.
I have a Copperjet 1616 modem connected with my Linksys (Cisco) WRT160N router and works like a charm for months.

I have tried to use the linksys wusb600n (ralink rt2870) on USB-2 on WDTV connected so with the included cable because it's too wide to put it in directly at USB-2 at the back of WDTV (I also tired with USB-1 but then no light was glowing the whole time). With USB-2 the connection light is almost the whole time green glowing on the wusb600n.
My other usb 16GB Sony stick (FAT) is connected to USB-1 with in the root of that stick:

RT2870STA.dat
net.config
and also wireless-mod-wdlxtv.app.bin

Screenshot of setting + About screen in WDLXTV:

(http://www.funriders.net/temp/screenshot_hardware_wdtv.jpg)
(http://www.funriders.net/temp/screenshot_software_wdtv.jpg)

My RT2870STA.dat file:
Quote
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
ChannelGeography=1
SSID=MyWirelessRouterSSIDname
NetworkType=Infra
WirelessMode=8
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
PktAggregate=0
WmmCapable=1
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=AES
WPAPSK=MyWirelessRouterNetworkKey
PSMode=CAM
AutoRoaming=0
RoamThreshold=70
APSDCapable=0
APSDAC=0;0;0;0
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_BADecline=0
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
HT_DisallowTKIP=1
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0
AntDiversity=0
BeaconLostTime=4

net.config file
Quote
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:

#specify time server host
#NTP=pool.ntp.org

#specify timezone
#TZ=PST8EDT


[ -e $AROOT/RT2870STA.dat ] && cp $AROOT/RT2870STA.dat /tmp
insmod $APATH/lib/modules/2.6.15-TvDock/rt2870sta.ko
ifconfig rausb0 up
udhcpc -H wdtv -i rausb0
Title: Re: *experimental* wireless usb support package
Post by: timeey on May 20, 2009, 06:29:41 AM
Just read the complete last site. I posted my changes there. With your quoted settings it doesn't work for me.
Title: Re: *experimental* wireless usb support package
Post by: pacorob on May 20, 2009, 06:54:49 AM
Just read the complete last site. I posted my changes there. With your quoted settings it doesn't work for me.

what do you mean with 'complete last site?' I saw your solution in the other topic smc-wusb-n to change rausb0 to ra0 this also worked for me!!
I now have an ip. I then receive the message at my pc (where the shared disk is) to share with media player the folder on the external harddisk. However on the wdtv it still keeps searching for it.. I only see in the video map folder USB1. I suppose I should see also there that network disk at my pc?
Title: Re: *experimental* wireless usb support package
Post by: skypeman on May 20, 2009, 07:36:00 AM
hi there,

i wonder if theres a list of VID/PID that are already supported.

Heres one from my device which isnt supported yet:

idVendor:           0x083A (Accton Technology Corporation)
idProduct:          0xE503

its a Zydas 1211B chipset. could somebody please tell me howto add this VID/VIP pair
manually.

thx
Title: Re: *experimental* wireless usb support package
Post by: zaphod beeblebrox on May 20, 2009, 04:05:08 PM
Hi Everybody!  :)

I need strong support on the wlan business.. I got a D-Link DWL G122 Rev. C1 (Vid/Pid 07d1:3c03) with a Rt73 chipset... On paper it should work with Zorander's mod.. (http://pl.wiki.wdtv.org/doku.php?id=wlanusb)

My italian fellow Cionci was able to connect the same dongle to an encrypted wlan (wpa) without much effort with pseudo-standard net.config and wpa_supplicant.conf files.. The problem is that this dongle doesn't seem to work with open wlan, which is what I really need..

Anybody here that can explain why wpa works and open wlan won't?
???

I 'd really really really really appreciate your help.. You will be graciously rewarded in an Heaven of your choice.

Saludos.
Title: Re: *experimental* wireless usb support package
Post by: wdtv101 on May 20, 2009, 06:08:14 PM
Just read the complete last site. I posted my changes there. With your quoted settings it doesn't work for me.

what do you mean with 'complete last site?' I saw your solution in the other topic smc-wusb-n to change rausb0 to ra0 this also worked for me!!
I now have an ip. I then receive the message at my pc (where the shared disk is) to share with media player the folder on the external harddisk. However on the wdtv it still keeps searching for it.. I only see in the video map folder USB1. I suppose I should see also there that network disk at my pc?
We don't know how you share your network disk in order to help you...

You can use hanewin NFS server to share your files...  there is a little guide I wrote in other thread...

http://wdtvforum.com/main/index.php?topic=686.0
Title: Re: *experimental* wireless usb support package
Post by: aoh74 on May 21, 2009, 06:24:07 AM
Hello all,
I have a Sitecom WL608 v1 wireless adapter which does not currently work. It uses the
Ralink RT2870 which is supported so I'm guessing the vid/pid need to be added somewhere.
The following is output to messages.txt on bootup:

Jan  1 00:00:21 wdtv user.notice root:  [0df6:003f] 1-1( 2.00,480m) 802.11 g WLAN/1.0

Is it possible/easy to do this myself or does Zorander need to include it in another build of wireless-mod-app?

Any help appreciated.

aoh
Title: Re: *experimental* wireless usb support package
Post by: jdogg69 on May 21, 2009, 07:04:05 PM
I was wondering if someone could help me set up my wdtv on my wireless network. I currently have a D-Link di-524 router and i am using a d-link DWL-G122 version c1 usb adapter however when i start up the media player it says "no ip". I have copied over the core-extras.app.bin and samba.app.bin-0.2 and wireless-mod-wdlxtv.app to the root of my usb drive and i am using WDLXTV version 0.5.3.2. I am using WPA-PSK with AES encryption. Here is what my net.config, net.mounts and wpa_supplicant.conf look like. I have added a password to my windows xp account so i could use a password in the net.mounts file. Also my firewall is off when i have tested and by router does broadcast ssid, i am basically using default setting on the router.

(net.config)

ifconfig $MDEV up
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf

(net.mounts)

xmount //192.168.0.101/My_Videos Videos cifs user=Josh,password=josh

(wpa_suplicant.conf)

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Sinner"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="confidential"
}


Title: Re: *experimental* wireless usb support package
Post by: jermaine on May 22, 2009, 05:44:12 AM
Hi,

I have the usb wireless Linksys WUSB54GC, but not work. Also i have the ext3 firmware on root, and when rebooting if i have the linksys usb wireless connected to the wd hd tv, it does not work (black screen).

I followed the rezmus tutorial for making work the lan wireless on the wd hd tv on wpa but nothing.

Have to change something more?

Thanks
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 22, 2009, 09:15:00 AM
Hi,

I have the usb wireless Linksys WUSB54GC, but not work. Also i have the ext3 firmware on root, and when rebooting if i have the linksys usb wireless connected to the wd hd tv, it does not work (black screen).

I followed the rezmus tutorial for making work the lan wireless on the wd hd tv on wpa but nothing.

Have to change something more?

Thanks
I suggest people in general, try out with open wifi first, to see if it works, then with WEP, and then with WPA/WPA2.
In your particular case, as I have this same model working with WPA2 (in ext3-boot 0.9.2), please post your net.config and wpa_supplicant.conf, and I will try to find what's wrong with your config.
Title: Re: *experimental* wireless usb support package
Post by: jermaine on May 22, 2009, 10:23:10 AM


Thanks
[/quote]
I suggest people in general, try out with open wifi first, to see if it works, then with WEP, and then with WPA/WPA2.
In your particular case, as I have this same model working with WPA2 (in ext3-boot 0.9.2), please post your net.config and wpa_supplicant.conf, and I will try to find what's wrong with your config.
[/quote]

In attach i send both files,

Thanks
Title: Re: *experimental* wireless usb support package
Post by: jermaine on May 22, 2009, 11:31:23 AM
I have the 1.02.07 firmware on flash. On boot (pen) i have ext3 last one.
My steps:

1 - Instaled the ext3 firmware
2 - on the pen with ext3 firmware i added wpa_supplicant.conf
3 - on the pen with ext3 firmware i added the file wireless-mod.app

the net.config and wpa_supplicant.conf i edite just like the tutorial

Thanks
Title: Re: *experimental* wireless usb support package
Post by: jermaine on May 22, 2009, 02:28:07 PM
I installed the wireless-mod.app.bin (0.0.3), and i get signal on my usb wireless linksys but not constant signal. Also i have on video folder the folder upnp.
I think is not ok. Here is my files:
Title: Re: *experimental* wireless usb support package
Post by: jermaine on May 22, 2009, 02:39:21 PM
Hi again,

I have this on iwlist_scan:

rausb0    Scan completed :
          Cell 01 - Address: 00:1D:7E:E3:8B:87
                    Mode:Managed
                    ESSID:""
                    Channel:6
                    Encryption key:on
                    Bit Rates:2 Mb/s

What this means?



Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 23, 2009, 02:59:14 AM

Well, in your net.config you have to modify some things.

If you want static ip, you should uncomment (remove the '#') in the 'DHCP=no' line.

Yo should uncomment the ifconfig and wpa_supplicant lines. The adaptor name in the wpa_supplicant, should be ralink, and you may need to put a sleep=2 line between ifconfig and wpa_supplicant.
It should be something like this:

Code: [Select]
ifconfig $MDEV up
sleep 2
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 23, 2009, 03:26:38 AM

An for the wpa_supplicant.conf

If you are using WPA2, you might need to add the following lines inside network={...}
Code: [Select]
proto=RSN
pairwise=CCMP TKIP

And just a hint to improve connection time. If you put this
psk="my passkey" , then the wdtv has to encode that password for your essid name, to obtain a hexadecimal key, everytime you connect.
You can give directly the hexadecimal key, so that the wdtv doesn't have to make the conversion.
If you have access to a linux box, (or a virtualized linux or cygwin under windows), you can execute the following command.
wpa_passphrase SSID passkey

You will obtain a psk=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
line, that you can use to replace the original psk="passkey" line in your wpa_supplicant.conf
Note that the hexadecimal key, is not between "" .
Title: Re: *experimental* wireless usb support package
Post by: fontes on May 23, 2009, 03:53:01 AM
Hi,

I have the Dlink DWL-122 wireless usb, but i cannot get working my wdhdtv on my network:

I have the files like this:

net.config:

HOST=wdtv


ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf





#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.112
GW=192.168.1.100
NM=255.255.255.0
DNS1=192.168.1.100
#DNS2=205.171.3.65

The wpa supplicant file:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="piaui"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="xxxxxxxx"
}

What is wrong?

I have the bin 0.0.3 file. My system is WAP and static ip
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 23, 2009, 04:12:32 AM
Hi,

I have the Dlink DWL-122 wireless usb, but i cannot get working my wdhdtv on my network:

I have the files like this:

net.config:

HOST=wdtv


ifconfig rausb0 up
Code: [Select]
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf




#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.112
GW=192.168.1.100
NM=255.255.255.0
DNS1=192.168.1.100
#DNS2=205.171.3.65[/color]

The wpa supplicant file:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="piaui"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="xxxxxxxx"
}

What is wrong?

I have the bin 0.0.3 file. My system is WAP and static ip


This is a prism chipset card, so I think it uses hostap driver module.
I think, that this "might" work:

wpa_supplicant -Bw -Dhostap -i$MDEV -c/boot/wpa_supplicant.conf

(If this works, someone should add it to the wdtv developers wiki, as the info for prism cards configuration seems to be missing)



Edit. I hadn't seen your ifconfig line. It needs to be modified too.

ifconfig $MDEV up


I think that in this cards the interface is wlan0 , but putting $MDEV you make sure it uses the right one.

Edit, Dlink DWL-122 is rt73 based, not prism.
Title: Re: *experimental* wireless usb support package
Post by: fontes on May 23, 2009, 04:24:17 AM


This is a prism chipset card, so I think it uses hostap driver module.
I think, that this "might" work:

wpa_supplicant -Bw -Dhostap -i$MDEV -c/boot/wpa_supplicant.conf

(If this works, someone should add it to the wdtv developers wiki, as the info for prism cards configuration seems to be missing)


Edit. I hadn't seen your ifconfig line. It needs to be modified too.



ifconfig $MDEV up


I think that in this cards the interface is wlan0 , but putting $MDEV you make sure it uses the right one.
[/quote]


Hi,

Modified, but nothig. I make ping on dos, and no answer.
No need to put the line sleep?

Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 23, 2009, 06:06:26 AM
Hi,

Modified, but nothig. I make ping on dos, and no answer.
No need to put the line sleep?

You can try putting sleep lines before and after ifconfig, and after wpa_supplicant line. In my Linksys rt73, sleep=2 worked, but some people use values of 5 (it depends on every usb dongle, I think).

Does the led of your USB dongle light up?
You can take a look at the messages.txt file in your boot device. It can help figuring out what is happening
Title: Re: *experimental* wireless usb support package
Post by: fontes on May 23, 2009, 06:21:48 AM

[/quote]

You can try putting sleep lines before and after ifconfig, and after wpa_supplicant line. In my Linksys rt73, sleep=2 worked, but some people use values of 5 (it depends on every usb dongle, I think).

Does the led of your USB dongle light up?
You can take a look at the messages.txt file in your boot device. It can help figuring out what is happening
[/quote]

Hi,

I have now the net.config:

ifconfig $MDEV up
sleep2
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
sleep2


DHCP=no
IP=192.168.1.112
GW=192.168.1.100
NM=255.255.255.0
DNS1=192.168.1.100

and the wpa_suppliant:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="piaui"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="xxxxxx"
}

And the usb wireless dongel has the lnk ligh on and off, continuosly. After the wdtvhd logo on the tv, the tv stays black...nothing happens after
I have the dongle usb wirelees on usb port2. In attch i send my message file.

Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 23, 2009, 07:10:22 AM
Hi,

I have now the net.config:

ifconfig $MDEV up
sleep2
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
sleep2


DHCP=no
IP=192.168.1.112
GW=192.168.1.100
NM=255.255.255.0
DNS1=192.168.1.100

and the wpa_suppliant:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="piaui"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="xxxxxx"
}

And the usb wireless dongel has the lnk ligh on and off, continuosly. After the wdtvhd logo on the tv, the tv stays black...nothing happens after
I have the dongle usb wirelees on usb port2. In attch i send my message file.

Well, googling around I have found that your Dlink DWL-122, is a rt73 based dongle (not a prism one, like I wrongly thought before).

So your
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
should work. (I'm not an expert, so I can only say what works for me)

I don't know if that makes any difference, but I have the DHCP and IPs lines before the ifconfig, and with an additional sleep=2 between them and ifconfig.

Make sure you are using the 0.3 version of wireless-mod.app.bin, and if using WPA2, add the
Code: [Select]
proto=RSN
pairwise=CCMP TKIP
lines inside
network={...}


Edit. And please, see what happens if you put sleep=5 instead of =2

Edit 2. I've just seen that in your net.config, you are using:
sleep2
while it should be:
sleep=2

(replace with a higher number like 5 if it still doesn't work)
Title: Re: *experimental* wireless usb support package
Post by: fontes on May 23, 2009, 01:45:49 PM

[/quote]

Well, googling around I have found that your Dlink DWL-122, is a rt73 based dongle (not a prism one, like I wrongly thought before).

So your
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
should work. (I'm not an expert, so I can only say what works for me)

I don't know if that makes any difference, but I have the DHCP and IPs lines before the ifconfig, and with an additional sleep=2 between them and ifconfig.

Make sure you are using the 0.3 version of wireless-mod.app.bin, and if using WPA2, add the
Code: [Select]
proto=RSN
pairwise=CCMP TKIP
lines inside
network={...}


Edit. And please, see what happens if you put sleep=5 instead of =2

Edit 2. I've just seen that in your net.config, you are using:
sleep2
while it should be:
sleep=2

(replace with a higher number like 5 if it still doesn't work)
[/quote]

Hi,

I use WAP, on router i have WAP personal and TKIP encryption. So my wpa_supplicant.conf is right this:

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="TerraTec"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="leixonenseeusou"
}

what you think?

Title: Re: *experimental* wireless usb support package
Post by: skypeman on May 24, 2009, 01:35:12 AM
again .. can anyone please tell me how to add new VID/PID's to the wireless-mod.

thx in advance

lars

P.S.:
or can sb add this line to the zd_usb.c and recompile.
Code: [Select]
{ USB_DEVICE(0x083a, 0xe503), .driver_info = DEVICE_ZD1211B },
Title: Re: *experimental* wireless usb support package
Post by: dika on May 24, 2009, 02:58:21 AM
My DWL-122 is a PRISM2 model.
Title: Re: *experimental* wireless usb support package
Post by: chipwreck on May 24, 2009, 11:33:35 AM
Hi guys!

First of all thank you very much for all your work and for you sharing the info.
Now to the problem, on the WDTV WIKI wireless dongle page it says someone has had success with a PRISM_A021 based device.
I have an old "TOPCOM Skyr@acer Wireless USB Stick 54 Mbps" which should be PRISM_A021 based if I'm not totally misinformed.
I've tried to get things working by reading alot of faq's and forum posts but as I'm more of a windows guy than a unix guy I haven't had much of success as I'm not finding any info specific for my hardware setup.
The LED's on the dongle won't even flash so something is really wrong. (the dongle works on a windows pc)
I'm trying using WDLXTV-0.5.3.2 and wireless-mod-wdlxtv.app.bin for the moment but if some other firmware/software combo solves the problem I'm willing to try it.
I just need the posibility to transfer files from my PC (win XP) to my WDTV over a wireless link.
I'm even willing to by a new usb wireless adapter if someone can point out a specific brand and model that really works as it's virtually impossible to go to a store and ask for a dongle with a specific chipset..

 / Chipwreck

Title: Re: *experimental* wireless usb support package
Post by: humbel on May 26, 2009, 12:46:45 AM
hi i have a problem with my DWL G122
first time i get connectet and all works very fine
if i reboot, nothing works get no connection with my wifi
if i put my usb pen in my pc net.config will be chmod 444 (before 777) dont know why, thats only with ext3boot firmware
i set net.config back to chmod 777 but i get no more connection, dont know whats the problem?
can me help me everyone?
Does ext3boot set other chmod rules to the net.config? and why?

my config is (stolen from avon :D )

Quote
sleep 2

ifconfig $MDEV rausb0 up
iwconfig $MDEV essid fritz

sleep 2
wpa_supplicant -Bw -Dralink -i$MDEV -c/tmp/mnt/sda1/wpa_supplicant.conf

sleep 2
HOST=wdtv
MTU=9000
DHCP=no
IP=192.168.178.11
GW=192.168.178.1
DNS1=192.168.178.1

sleep 5

and my wpa is
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="fritz"
# uncomment next line if your ap doesn't broadcast ssid
scan_ssid=1
key_mgmt=WPA-PSK
psk="mypw"
}
have anyone a idea? pls?

i cant use b-rad firmware, every booting no-ip :(
Title: Re: *experimental* wireless usb support package
Post by: maduenyo on May 26, 2009, 01:23:29 AM
Hi everybody,

I've been searching for all in one howto about the wireless configuration, but no luck...
So I'm committed to write a very detailed howto if I get the wireless to come up.

So far, that's the configuration I'm using but still without success (no IP).

HARDWARE -----------------------------------------------------------------------------------

USB pendrive:     1Gb FAT32 formatted (formatted using HP USB Disk Storage Format Tool v2.1.8 )
Wireless adapter: D-Link G-122 Rev C1

SOFTWARE -----------------------------------------------------------------------------------

(downloaded from B-RAD web site)

Firmware:           1.02.07_B-RAD.CC_WDLXTV-0.5.3.2
Wireless module:  wirelessmod-wdlxtv.app.bin-0.2


CONFIGURATION ------------------------------------------------------------------------------

- Router Access Point:
ESSID:          myWiFi
Encryption:    No encryption (once it works I will move to WEP and then to WAP).
MAC filtering:  Disabled

- net.config (edited with WordPad):
HOST=wdtv
DHCP=yes
ifconfig $MDEV up
sleep 5
iwconfig $MDEV essid myWiFi
sleep 5

PROCEDURE ---------------------------------------------------------------------------------

- Firmware upgrade:
a) Format USB pendrive to FAT32.
b) Unzip wdtv.bin and wdtv.ver  from 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2.zip.
c) Copy wdtv.bin and wdtv.ver to USB pendrive in the root directory (in my case "F:\").
d) Insert USB pendrive in USB port 1 (side port) of WDTV and switch it ON (connect power cable).
e) Confirm firmware upgrade.
d) Once finished, the WDTV reboots and shows new splash with WD LX TV logo.
e) Turn off WDTV (with the remote power button) and the remove power cable.
f) Remove USB pendrive.

> Firmware update: SUCCESSFUL.

- Wireless:
a) If wireless-mod.app-bin is zipped, unzip from wireless-mod-wdlxtv.app.zip.
b) Copy wireless-mod.app-bin (10MB) to USB pendrive in the root directory (in my case "F:\").
Now, there are 3 files in the root directory of the pendrive (wdtv.bin, wdtv.ver and wireless-mod.app-bin).
c) Copy net.config file (see file content above) to USB pendrive in the root directory.
d) Insert USB pendrive in USB port 1 (side port) of WDTV.
e) Insert USB D-Link G-122 in the USB port 2 (rear port).
f) Switch on the WDTV (connect power cable).
g) WDTV boots up but at the splash screen it says no IP.
h) The D-Link G-122 has 2 leds (ACT and LINK), the Link blinks every 5 seconds.
i) In the about it also says no IP.

> Wireless status: No IP.

TROUBLESHOOTING -------------------------------------------------------------------

I guess I'm doing something wrong, but no idea what.

I tried with several wireless-mod.app.bin:
- wireless-mod-wdlxtv.app.bin (10 MB) from B-RAD web site.
- wireless-mod.app.bin v0.3 (2.30 MB) zorander’s experimental pack from WDTVC web site.

I've also tried with static IP, with Jumbo Frames and rausb0 instead of $MDEV in the net.config
but no success.

I've also installed the log-saver.app.bin to get logs, however I'm not an expert
in Linux and I do not know very what to look for in the log files generated.


Any help will be welcome!!

Thanks and regards.
Title: Re: *experimental* wireless usb support package
Post by: jdogg69 on May 26, 2009, 03:45:23 AM
Yeah i have the dwl-g122 adapter too and i am also using b-rad's firmware like you and I can't get the wireless to work either. I have tried everything but I have now officially gave up :(.
Title: Re: *experimental* wireless usb support package
Post by: CrashX on May 26, 2009, 06:35:24 AM
maduenyo:

1) It should be sleep=5 not sleep 5
2) net.config  should be saved as unix format not windows format ... use notepad ++ or something else that has that option ..
3) Post your messages.txt ..
Title: Re: *experimental* wireless usb support package
Post by: maduenyo on May 26, 2009, 08:20:24 AM
Hi CrashX,

I've followed your instructions, however it does not want to come up. The LNK led in the USB D-Link G-122
blinks once every 4-5 seconds and the Act is OFF.

After editing the net.config I've converted it to UNIX format with DOS2UNIX, I think it should be fine now.

I have highlighted several lines in the messages.txt.0, it seems the USB D-Link G-122 is recognized and the wireless module mounted, but I do not see anything saying if the net.config has been loaded.

Just in case, I gonna edit the net.config with notepad++ as you've suggested...

PS: I do not know if that could be a problem but this time I did not connect the WDTV to the TV set by any mean.

Thanks!!!

Here you are the files (in 2 parts):

net.config (converted to UNIX with DOS2UNIX) ----------------------------------------------------------

HOST=wdtv
DHCP=yes
ifconfig $MDEV up
sleep=5
iwconfig $MDEV essid myWiFi
sleep=5

messages.txt.0 ---------------------------------------------------------------------------------------

Dec 31 16:00:39 WDTV-cbf04 syslog.info syslogd started: BusyBox v1.10.0
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Dec 31 16:00:39 WDTV-cbf04 user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: CPU revision is: 00019069
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Determined physical RAM map:
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: On node 0 totalpages: 94208
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Built 1 zonelists
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: Kernel command line: console=ttyS0
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Synthesized TLB refill handler (20 instructions).
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Using 148.500 MHz high precision timer.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Console: colour dummy device 80x25
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Mount-cache hash table entries: 512
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Checking for 'wait' instruction...  available.
Dec 31 16:00:39 WDTV-cbf04 user.notice root: 1.02.07.WDLXTV-0.5.3.2
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: NET: Registered protocol family 16
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Region size is 16384KB
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: SCSI subsystem initialized
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: usbcore: registered new driver usbfs
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: usbcore: registered new driver hub
Dec 31 16:00:39 WDTV-cbf04 user.notice root: Displaying detected USB devices...
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Created /proc/cpucache_info entry.
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: fuse init (API version 7.3)
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: Initializing Cryptographic API
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: io scheduler noop registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: io scheduler anticipatory registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: io scheduler deadline registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: io scheduler cfq registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: loop: loaded (max 8 devices)
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: number of CFI chips: 1
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: Using physmap partition definition
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: Adding partition #1-#5
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: TangoX USB initializing...
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: hub 1-0:1.0: USB hub fou
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: nd
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: hub 1-0:1.0: 2 ports detected
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: TangoX USB was initialized.
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Title: Re: *experimental* wireless usb support package
Post by: maduenyo on May 26, 2009, 08:23:43 AM
and second part:

Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: hub 2-0:1.0: USB hub found
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: hub 2-0:1.0: 2 ports detected
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: Initializing USB Mass Storage driver...
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: usb-storage: device found at 2
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: usb-storage: waiting for device to settle before scanning
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: usbcore: registered new driver usb-storage
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: USB Mass Storage support registered.
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: NET: Registered protocol family 2
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: TCP reno registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: TCP bic registered
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: NET: Registered protocol family 1
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: NET: Registered protocol family 17
Dec 31 16:00:39 WDTV-cbf04 user.info kernel: Freeing unused kernel memory: 252k freed
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel:   Vendor: UDISK     Model: PDU01_1G 72C2.0   Rev: 0.00
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 02
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: SCSI device sda: 2047999 512-byte hdwr sectors (1049 MB)
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: sda: Write Protect is off
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: sda: Mode Sense: 00 00 00 00
Dec 31 16:00:39 WDTV-cbf04 user.err kernel: sda: assuming drive cache: write through
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: SCSI device sda: 2047999 512-byte hdwr sectors (1049 MB)
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: sda: Write Protect is off
Dec 31 16:00:39 WDTV-cbf04 user.debug kernel: sda: Mode Sense: 00 00 00 00
Dec 31 16:00:39 WDTV-cbf04 user.err kernel: sda: assuming drive cache: write through
Dec 31 16:00:39 WDTV-cbf04 user.info kernel:  sda: sda1
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Dec 31 16:00:39 WDTV-cbf04 user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Dec 31 16:00:40 WDTV-cbf04 user.notice root:  [1307:0163] 1-1( 2.00,480m) USB Mass Storage Device/000000000012FB
Dec 31 16:00:40 WDTV-cbf04 user.debug kernel: usb-storage: device scan complete
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: llad: module license 'LGPL' taints kernel.
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
Dec 31 16:00:40 WDTV-cbf04 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Dec 31 16:00:40 WDTV-cbf04 user.notice root:  [07d1:3c03] 1-2( 2.00,480m) 802.11 bg WLAN
Dec 31 16:00:40 WDTV-cbf04 user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Dec 31 16:00:41 WDTV-cbf04 user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Dec 31 16:00:43 WDTV-cbf04 user.notice root: crazymounter: mounting devices
Dec 31 16:00:43 WDTV-cbf04 user.notice root: /dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
Dec 31 16:00:43 WDTV-cbf04 user.notice root: /dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
Dec 31 16:00:43 WDTV-cbf04 user.notice root: /dev/sda1: LABEL="CIBOX" UUID="E044-1CCD" TYPE="vfat"
Dec 31 16:00:44 WDTV-cbf04 user.notice root: /dev/sda1: LABEL="CIBOX" UUID="E044-1CCD" TYPE="vfat"
Dec 31 16:00:44 WDTV-cbf04 user.notice root: xmount.scan: Will not mount /dev/sda1 (vfat)
Dec 31 16:00:44 WDTV-cbf04 user.notice root: crazymount: mounting app binaries...
Dec 31 16:00:45 WDTV-cbf04 user.notice root: DEVICE /dev/sda1 CONNECTED
Dec 31 16:00:45 WDTV-cbf04 user.notice root: log-saver app found
Dec 31 16:00:45 WDTV-cbf04 user.notice root: Mounting /tmp/mnt/sda1/log-saver.app.bin at /apps/log-saver
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=68, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=1028, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=12, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=1028, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=12, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=1252, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: attempt to access beyond end of device
Dec 31 16:00:45 WDTV-cbf04 user.info kernel: loop0: rw=0, want=1028, limit=8
Dec 31 16:00:45 WDTV-cbf04 user.warn kernel: UDF-fs: No partition found (1)
Dec 31 16:00:45 WDTV-cbf04 user.notice root: wireless-mod-wdlxtv app found
Dec 31 16:00:45 WDTV-cbf04 user.notice root: Mounting /tmp/mnt/sda1/wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Dec 31 16:00:45 WDTV-cbf04 user.warn kernel: UDF-fs: No VRS found
Dec 31 16:00:45 WDTV-cbf04 user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Dec 31 16:00:46 WDTV-cbf04 user.notice root: adjusting LIBPATH
Dec 31 16:00:48 WDTV-cbf04 user.notice root: adjusting PATH
Dec 31 16:00:48 WDTV-cbf04 user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Dec 31 16:00:54 WDTV-cbf04 user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:54 WDTV-cbf04 user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver asix
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver dm9601
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver kaweth
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver pegasus
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver rtl8150
Dec 31 16:00:54 WDTV-cbf04 user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:54 WDTV-cbf04 user.info kernel: usbcore: registered new driver cdc_ether
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver catc
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver cdc_subset
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver net1080
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver plusb
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver rndis_host
Dec 31 16:00:55 WDTV-cbf04 user.info kernel: usbcore: registered new driver gl620a
Dec 31 16:00:56 WDTV-cbf04 user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:56 WDTV-cbf04 user.info kernel: Loading wireless extentions module...
Dec 31 16:00:56 WDTV-cbf04 user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:57 WDTV-cbf04 daemon.info utelnetd[941]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Dec 31 16:00:59 WDTV-cbf04 user.debug kernel: ir: Enable NEC decoder (0x00000000)
Dec 31 16:00:59 WDTV-cbf04 user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Dec 31 16:02:17 WDTV-cbf04 user.notice root: spinning down /dev/sda1

Files in the USB pendrive -------------------------------------------------------------------------------

05/26/2009  05:54 PM               491 net.config
04/23/2009  07:58 PM               620 net.mounts
05/25/2009  10:54 PM             4,096 log-saver.app.bin
01/01/2000  12:02 AM            18,472 messages.txt.0
01/01/2000  12:02 AM             8,479 dmesg.txt.0
05/26/2009  09:36 AM        10,485,760 wireless-mod-wdlxtv.app.bin
01/01/2000  12:02 AM             2,601 system.txt.0

Thanks!!
Title: Re: *experimental* wireless usb support package
Post by: maduenyo on May 26, 2009, 08:47:06 AM
Just an add-on to the last post.

I've just tried with a different wireless module, the wireless-mod.app.bin (0.0.3 from a link provided in this forum).

And the messages.txt.0 looks better, I just attach the last part:

Dec 31 16:00:54 WDTV-1d3ac user.info kernel: Loading wireless extentions module...
Dec 31 16:00:54 WDTV-1d3ac user.warn kernel: zd1201: Unknown symbol release_firmware
Dec 31 16:00:54 WDTV-1d3ac user.warn kernel: zd1201: Unknown symbol request_firmware

Dec 31 16:00:54 WDTV-1d3ac user.notice kernel: ZD1211B - version 2.19.2.9
Dec 31 16:00:54 WDTV-1d3ac user.info kernel: usbcore: registered new driver zd1211b
Dec 31 16:00:55 WDTV-1d3ac user.notice kernel: arusb - version 0.0.0.999
Dec 31 16:00:55 WDTV-1d3ac user.info kernel: usbcore: registered new driver Otus
Dec 31 16:00:55 WDTV-1d3ac user.warn kernel: rtusb init --->
Dec 31 16:00:55 WDTV-1d3ac user.info kernel: usbcore: registered new driver rt2870
Dec 31 16:00:55 WDTV-1d3ac user.warn kernel: idVendor = 0x7d1, idProduct = 0x3c03
Dec 31 16:00:55 WDTV-1d3ac user.notice root: net.agent:  Called for rausb0
Dec 31 16:00:56 WDTV-1d3ac user.warn kernel: => usb_rtusb_open
Dec 31 16:00:56 WDTV-1d3ac user.debug kernel: rausb0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
Dec 31 16:00:56 WDTV-1d3ac user.notice root: net.agent: No IP provided, doing DHCP
Dec 31 16:00:56 WDTV-1d3ac user.info kernel: usbcore: registered new driver rt73

Dec 31 16:00:57 WDTV-1d3ac daemon.info utelnetd[886]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Dec 31 16:00:59 WDTV-1d3ac user.debug kernel: ir: Enable NEC decoder (0x00000000)
Dec 31 16:00:59 WDTV-1d3ac user.debug kernel: ir: Enable RC5 decoder (0x00000000)

It seems there is a problem with the driver (??), in any case, at least it tries to get an IP by DHCP...
I feel the solution is getting closer, but a little bit help is still needed...

Thanks!
Title: Re: *experimental* wireless usb support package
Post by: zorro on May 27, 2009, 06:32:59 AM
Hi everyone,

I have exacly the same issue as "maduenyo" describes, Act led flashing every 5th second.
And from messages.txt.0 I can see exactly the same trace.

Dec 31 16:00:56 WDTV-1d3ac user.debug kernel: rausb0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
Dec 31 16:00:56 WDTV-1d3ac user.notice root: net.agent: No IP provided, doing DHCP
Dec 31 16:00:56 WDTV-1d3ac user.info kernel: usbcore: registered new driver rt73


My HW is also USB D-Link G-122, hope that anyone can help with this issue.

Thx.
Title: Re: *experimental* wireless usb support package
Post by: bottosac on May 27, 2009, 02:13:29 PM
Hi all,
I have a D-Link G-122 rev C1 connected to a Netgear DB834G with broadcast ssid, no dhcp, encryption WPA with ext3-boot-0.9.2 firmware and zorader wifi package and work fine!
Here my configuration files

net.config
Code: [Select]
#
# Network configuration file

#You can override the hostname here:

#wlan lines

HOST=wdtv

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

#DHCP=yes

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.50
GW=192.168.1.1
NM=255.255.255.0
DNS1=84.208.20.110
DNS2=84.208.20.111

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

 

and wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="myssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="mypskkey"
}

Title: Re: *experimental* wireless usb support package
Post by: zaphod beeblebrox on May 28, 2009, 08:45:36 AM
Hi everyone!

I have tried a lot of time to download the Zorander wireless pack from mediafire (http://www.mediafire.com/?dz1nmqloazm ..the link should be right) but I cannot reach the page.. No firewall problems whatsoever, so I suppose it's the website... Any tip? Maybe a mirror?

Thanks  ;)
Title: Re: *experimental* wireless usb support package
Post by: maduenyo on May 28, 2009, 09:24:26 AM
Hi Zorro,

Cionci has given me the solution I post here.

Thanks, thanks, thanks Cionci!!

My HARDWARE -------------------------------------------------------------------

USB drive 1GB (to store firmware and modules)
USB D-Link G-122 Rev. C1 (check revision at the rear of the dongle)
WDTV HD (of course ;D)

CONFIG -------------------------------------------------------------------------

net.config

HOST=wdtv.hd
SUPPRESS_OTHERS=yes
DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

# Static IP Configuration:  (only if not DHCP), it works too

#DHCP=no
#IP=type desired IP address
#GW=type naetwork gateway IP address
#NM=255.255.255.0
#DNS1=first ISP nameserver
#DNS2=second ISP nameserver

#
# Optional:  specify time server host:

NTP=0.pool.ntp.org

# rt73 device (but I think that other chipsets are affected) works randomly without command below. It's simply a 5 seconds delay.
sleep 5



wpa_supplicant.conf

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="type your SSID"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="type your key here"
}



SOFTWARE ----------------------------------------------------------------------------

FIRMWARE:
zorander ext3:
     http://www.wdtvc.com/downloads/
     ext3-boot    version 0.9.1

B-Rad:
     http://www.wdtvc.com/downloads/
     B-RAD.CC WDLXTV    version 0.5.2 (FW 1.02.07)

(They are not the latest versions, but they work anyway and they are available in the same link)

WIRELESS module:
     http://www.wdtvc.com/downloads/
     Zorander’s wireless-mod.app.bin version 0.3

OPTWARE module:
     http://www.wdtvc.com/downloads/
     Optware for WD TV version 0.2


INSTRUCTIONS ---------------------------------------------------------------------------

Copy the files in the zorander or b-rad zip to the root directory of a FAT16 or FAT32 formatted USB drive.
Copy also the wireless and the optware to the root directory of the USB drive.

Attach the USB drive to the WDTV and after the firmware upgrade (if needed), it should work. The LNK led should
change to solid and the ACT should blink once the WDTV is up.

By the way, do not forget to double check that the wireless config in the net.config and wpa_supplicant.conf match
your home network settings. I would recommend to get familiar with the wireless settings configuring your Wireless
dongle on your PC and verifying it works fine and then try with WDTV.

Good luck!!
M
Title: Re: *experimental* wireless usb support package
Post by: CrashX on May 28, 2009, 10:00:37 AM
maduenyo:

Can you check the following since you have gotten wireless working:

1) If you put the wireless configuration at the end of net.config does it still work ?
2) wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf  ? Does it matter if you have space after parameter ..
"-D ralink" vs "-Dralink"
3) Where did "ralink" come from ? Should it be $MDEV
Title: Re: *experimental* wireless usb support package
Post by: zaphod beeblebrox on May 28, 2009, 12:34:41 PM
Hi everyone!

I have tried a lot of time to download the Zorander wireless pack from mediafire (http://www.mediafire.com/?dz1nmqloazm ..the link should be right) but I cannot reach the page.. No firewall problems whatsoever, so I suppose it's the website... Any tip? Maybe a mirror?

Thanks  ;)

no one? really? At least tell me if the link works for you, please :-)
Title: Re: *experimental* wireless usb support package
Post by: skypeman on May 28, 2009, 01:24:35 PM
works.

try this one:

http://netload.in/dateimIKcbNcfYz/wireless-mod.app.bin.htm

P.S.: I still need help adding VID/VIP pairs .. or does anyone know when the next version comes out?
Title: Re: *experimental* wireless usb support package
Post by: zaphod beeblebrox on May 28, 2009, 01:27:27 PM
works.

try this one:

http://netload.in/dateimIKcbNcfYz/wireless-mod.app.bin.htm




Thanks A LOT, man.  ;)
Title: Re: *experimental* wireless usb support package
Post by: nick61 on May 28, 2009, 10:47:39 PM
Hi, thanks to all of you who's working to improve the little wdtv box.

I've succeeded to link my wdtv in the home network with an usb ethernet on utp cable stick realtek (first one in the left in the pictures below).
Unfortunately, I did not have any luck with the wireless sticks (nor dlink dwl-g122 rev c1, third stick from left, nor zydas 1211 based stick, first one in the right side).


(http://www.freeimagehosting.net/uploads/th.92c7fed594.jpg) (http://www.freeimagehosting.net/image.php?92c7fed594.jpg)

(http://www.freeimagehosting.net/uploads/th.2145d6e4e2.jpg) (http://www.freeimagehosting.net/image.php?2145d6e4e2.jpg)

@maduneyo
There is a dispute:
sleep=5
or
sleep 5
so with or without equal sign ?

and another unclear line:

wpa_supplicant -B -D ralink.....
or
wpa_supplicant -B w -D ralink.... (as in the rezmus tutorial here: http://www.wdtvc.com/2009/04/06/how-to-config-wifi-usb-adapter-with-wd-tv/)
(there is a missing "w" after "-B")

and finally, are spaces important or not ?

So, there is a difference between:

wpa_supplicant -B -D ralink.....
and
wpa_supplicant -B -Dralink..... ?
(there must be a space or not between "-D" and "ralink")

Anyway, I suspect that with b-rad's 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2 and wirelessmod-wdlxtv.app.bin-0.2 there is no chance to have the wireless link up until now, and the reported working links are made only with zorander's ext3-boot.

So, please guys, check the sticks in the pictures and tell me if there is any chance to have a wireless link on a daily use with b-rad's firmware.

Thanks,



Title: Re: *experimental* wireless usb support package
Post by: zorro on May 28, 2009, 11:45:40 PM
Hi maduenyo,

Thanks for posting your solution, unfortunalty this did not work for me..... :'(
I'm using the same usb HW as you are, USB D-Link G-122 Rev. C1. My router is a Dlink DI-524.
I will post the messages.txt later.

Just two questions before I post the file.
Does it matter in wich port the USB dongle is mounted, and also if I need to use a specific Channel in my router?
Do I need to specify the channel for the USB dongle?

Thx
 
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on May 29, 2009, 10:54:51 AM
See answers in red.

@maduneyo
There is a dispute:
sleep=5
or
sleep 5
so with or without equal sign ?
It works with the equal sign.
and another unclear line:

wpa_supplicant -B -D ralink.....
or
wpa_supplicant -B w -D ralink.... (as in the rezmus tutorial here: http://www.wdtvc.com/2009/04/06/how-to-config-wifi-usb-adapter-with-wd-tv/)
(there is a missing "w" after "-B")
It works with the -Bw.

-w = wait for interface to be added, if needed (So it's safer to put the "w")

and finally, are spaces important or not ?

So, there is a difference between:

wpa_supplicant -B -D ralink.....
and
wpa_supplicant -B -Dralink..... ?
(there must be a space or not between "-D" and "ralink")
It works without spaces, but probably it doesn't matter.
Anyway, I suspect that with b-rad's 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2 and wirelessmod-wdlxtv.app.bin-0.2 there is no chance to have the wireless link up until now, and the reported working links are made only with zorander's ext3-boot.

So, please guys, check the sticks in the pictures and tell me if there is any chance to have a wireless link on a daily use with b-rad's firmware.

Thanks,
Sorry, I don't know about b-rad's. I use Zorander's ext3-boot.



Title: Re: *experimental* wireless usb support package
Post by: nick61 on May 29, 2009, 12:14:53 PM

Thank you, Mike
Title: Re: *experimental* wireless usb support package
Post by: whiteboy on May 29, 2009, 12:57:30 PM
Can anyone make any sense of this.  Maybe it says here what I'm doing wrong??

This is the messages.txt file.

http://www.mediafire.com/?sharekey=a406caed6927a6a9d1014a7a667fa2b4e04e75f6e8ebb871
Title: Re: *experimental* wireless usb support package
Post by: jdogg69 on May 29, 2009, 09:47:04 PM
i have a dlink dwl-g122 ver.c1 adapter and after spending hours using b-rad's firmware i finally decided to switch to zoranders firmware. my wireless network now works thanks to cionci's settings ( took me all of 10 mins to get it going)

net.config

HOST=wdtv.hd
SUPPRESS_OTHERS=yes
DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

# Static IP Configuration:  (only if not DHCP), it works too

#DHCP=no
#IP=type desired IP address
#GW=type naetwork gateway IP address
#NM=255.255.255.0
#DNS1=first ISP nameserver
#DNS2=second ISP nameserver

#
# Optional:  specify time server host:

NTP=0.pool.ntp.org

# rt73 device (but I think that other chipsets are affected) works randomly without command below. It's simply a 5 seconds delay.
sleep 5



wpa_supplicant.conf

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="type your SSID"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="type your key here"
}
Title: Re: *experimental* wireless usb support package
Post by: nick61 on May 30, 2009, 01:29:14 AM
Could someone spend some time to post a little quick step-by-step tutorial for flashing/using zorander's ext3-boot, with links to the compiled packages and actual posibilities described ?

I couldn't find an overall one, that's the reason I insisted on b-rad's firmware for trying wireless link (there is the rezmus wlan tutorial and the b-rad's site for this firmware).

As probably most of us, I am interested in testing wlan, sharing, ftp access, maybe torrents access posibilities, and I'm not a linux specialist, but I think I'm able to follow directions and I'm ready to assume some risks :)

Sorry if there is already such a tutorial posted, maybe someone could post the link to it.

Thanks,
Title: Re: *experimental* wireless usb support package
Post by: Zane on May 30, 2009, 05:55:44 PM
Any idea if there will be support for the RT2500 Ralink Chipset?
Title: Re: *experimental* wireless usb support package
Post by: sirish19 on May 31, 2009, 01:36:27 AM
Hi All, I need some help setting up a wireless connection.  I have gotten everything up networked with a USB-LAN adapter using b-rad's WDLXTV and samba app.  I want to set up a wireless for my second WDTV using a wireless dongle.  The dongle that I have is EDUP Wireless USB Adapter 54M.  From the WIKI page http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page it looks like this is based on the Atheros Otus chipset (assuming that it is the same as the EDUP Wireless USB Adapter 11g).  The page shows "fix me" on there but I am not sure what that means.  I had actually ordered the RaLink rt73 from dealextreme.com but it was back ordered for 2 weeks and when it finally came, they ended up sending me a different one.  I guess that is what you would expect for $10 and free international shipping....

It may be simply that this adapter is not supported, but I want to make sure that I have everything else configured right before trying my luck at ordering another one. 

Here is what I have on my pen drive:

FW Zorander's ext3-boot.0.8.7.2
     Zorander's wireless-mod.app
     wpa_supplicant
     samba.app
     net.config
     net.mounts

My net.config file looks like this:

#
# Network configuration file

#You can override the hostname here:

#wlan lines

HOST=wdtv

ifconfig $MDEV up
sleep=2
wpa_supplicant -Bw -D otus -i$MDEV -c/boot/wpa_supplicant.conf


#DHCP=yes


# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.11.3
GW=192.168.11.1
NM=255.255.255.0
DNS1=192.168.11.1
DNS2=192.168.11.1

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

and my wpa_supplicant file looks like this:

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your_ap_name"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="yourpass"
}


your_ap_name = my routers SSID and yourpass = my (I did leave in quotes but wasn't sure if that is correct or not).

My problem is that I am not getting any IP address and the ACT lamp on the dongle does nothing. 

It would be greatly appreciated if someone has some idea about what is wrong.  I have attached the message file below.

Thanks.




Title: Re: *experimental* wireless usb support package
Post by: skypeman on May 31, 2009, 04:46:10 PM
this mod is dead .. i`ve asked like three times for adding some VID/PID`s but nothing happened.
Title: Re: *experimental* wireless usb support package
Post by: Spartan on June 01, 2009, 05:27:40 PM
Just a simple question.  Is anyone able to get the wireless working with WDLXTV 0.5.X firmware?
I tried all kind of things and so far no luck with getting and IP address. 
Title: Re: *experimental* wireless usb support package
Post by: dadant_de on June 02, 2009, 02:43:19 AM
Just a simple question.  Is anyone able to get the wireless working with WDLXTV 0.5.X firmware?
I tried all kind of things and so far no luck with getting and IP address.  
yes.
2 major general issues:

*) wireless-mod-wdlxtv.app.bin doesn't seem to work for me at all, use wireless-mod.app.bin instead

**) path variable to wpa_supplicant in net.config is wrong for WDLXTV (for ext3-boot it's OK).
use
wpa_supplicant -Bw -Dralink -i$MDEV -c/tmp/mnt/sda1/wpa_supplicant.conf
instead of
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf
(edit drivers according your hardware)

***) sleep=2 or sleep=5 at the end of net.config and between the driver-lines could help.

****) adding SUPPRESS_OTHERS=yes after to the HOST-line is another hint.

and there are very probably some other issues regarding the used hardware/firmware.
my wireless network e.g. just works occasionally (Sunday perfect, Monday nothing).

good luck.





Title: Re: *experimental* wireless usb support package
Post by: nick61 on June 02, 2009, 08:14:57 AM

FINALY ! I do confirm the wlan link is working with dlink dwl-g122 ver.c1 and b-rad's 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2, THANKS DADANT_DE ! for the corect path in net.config

Here is my net.config:

HOST=wdtv
SUPPRESS_OTHERS=yes
MTU=9000
DHCP=yes
sleep=5
ifconfig $MDEV up
sleep=5
iwconfig $MDEV essid your_ssid
sleep=5
wpa_supplicant -B -D ralink -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep=5
NTP=0.pool.ntp.org
sleep=5

(yes, I know there is some kind of paranoia with sleep=5, but after about 1113,5 reflashes, you could imagine what was in my mind :) but I really don't think it's necessary all of them)

and wpa_supplicant:

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="your_ssid"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="your_pass"
}

Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on June 02, 2009, 10:13:47 AM
I'm pretty sure you can remove this line. (Along with one of the sleep lines)
iwconfig $MDEV essid your_ssid

This is not needed when you use wpa_supplicant
Title: Re: *experimental* wireless usb support package
Post by: nick61 on June 02, 2009, 10:09:43 PM
Some not very good news:

After about 20-30 mins after boot, with wdtv stoped from remote (in stand-by), the device freezes, with continous access on external local connected hdd. The only method to restart is to plug power off and back on.

Configuration is:
- 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2
- Zorander’s wireless-mod.app.bin version 0.3

Ok, back to tests...

BTW, there is any possibility to move all the necessary modded files/modules inside wdtv, so without any need to have some other files on an external device for boot ?

Thanks

Title: Re: *experimental* wireless usb support package
Post by: Valenrotpunk on June 03, 2009, 12:05:07 PM
Hi nick61,

I have copied your net.config and wpa_suplicant.config but doesn´t work for me.

I use the same firmware, wireless mod and dlink usb wifi. When I boot WDTV, I can see "no IP" in config menu.

Could you explain which files and folder structure use in you flash drive?

Thanks

(Excuse me for my english. I´m from Spain and it is not good than I like it)
Title: Re: *experimental* wireless usb support package
Post by: gonzalovalenzuela on June 03, 2009, 04:57:00 PM
I give up!!! , My config is:

- 1.02.07_B-RAD.CC_WDLXTV-0.5.3.2
- Zorander’s wireless-mod.app.bin version 0.3

my config files

wpa_supplicant.conf

Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="TOMATO"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="my pass"
}


net.config

Code: [Select]
HOST=WDHDTV
SUPPRESS_OTHERS=yes
MTU=9000
DHCP=yes
sleep=1
ifconfig $MDEV up
sleep=1
wpa_supplicant -B w -D wext -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep=1
NTP=pool.ntp.org

(I try using -Dwext -D wext -D otus -Dotus)

and the wireless work, get IP, but using my neighbor's network !!!! , he had an open wireless network, but I cant get my WDTV connect to MY FU**** WIRELES!!!
Title: Re: *experimental* wireless usb support package
Post by: nick61 on June 04, 2009, 06:31:10 AM
@Valenrotpunk

This is the directory on the usb stick (FAT):

02-Jun-09  19:17 PM               230 net.config
27-May-09  13:25 PM                34 net.mounts
30-Mar-09  22:29 PM        10,485,760 samba.app.bin
12-May-09  18:03 PM        13,848,608 wdtv.bin
12-May-09  18:03 PM                53 wdtv.ver
26-May-09  09:29 AM         2,420,736 wireless-mod.app.bin
27-May-09  13:25 PM               163 wpa_supplicant.conf
               7 File(s)     26,755,584 bytes
               0 Dir(s)   1,033,912,320 bytes free

The links for firmwares:

http://rapidshare.com/files/232304437/1.02.07_B-RAD.CC_WDLXTV-0.5.3.2.zip
http://www.wdtvc.com/wp-content/plugins/smartcounter/redirect.php?dcp_action=goto&dcp_id=21 (or http://www.mediafire.com/?dz1nmqloazm)
http://www.wdtvc.com/wp-content/plugins/smartcounter/redirect.php?dcp_action=goto&dcp_id=27 (or http://rapidshare.com/files/215880851/samba.app.bin-0.1.zip)

I suspect you have a wireless router configuration problem (see below).
Also, there is a posibility to show at first "no IP" but if you look after 30-60 sec. in settings-system-about you could have a nice surprise :)
Unfortunately, it works only about 30 mins., then freezes...

@gonzalovalenzuela

I suppose you have a router with tomato firmware (because of ssid :)
Put security settings at "WPA Personal", I had troubles with other settings...

good luck
Title: Re: *experimental* wireless usb support package
Post by: kebabinho on June 04, 2009, 11:47:09 PM
HI,

only just recieved my device and hoping some can help me? step by step i have

Downloaded ** WDLXTV-0.5.3.2 **
Put the files on a flashdisk
Flashed the device
Downloaded ** wirelessmod-wdlxtv.app.bin-0.2 **
placed on the flashdisk which still has the firmware files
altered the net.config and added WPA_SUPPLICANT.conf as detailed below
Inserted my flashdisk and Wireless LAN (Phillips SNU5600/00 which has the ZyDas chipset and i have seen it on a list on this thread somewhere)
Pulled the power chord, and then plugged it back in

The light comes on the philips device, but when the WD device finally loads up i get no IP on the screen and in the about screen.
Am i meant to flash the firmware again with the modified net.config?

details of the files are:

net config
 
#
# Network configuration file
#You can override the hostname here:
HOST=wdtv
# if you do not set a hostname,a random one is assigned.
# attempt to set jumbo frames
MTU=9000
#
# Dynamic IP Configuration:
#DHCP=yes
#
# Static IP Configuration: (only if not DHCP)
DHCP=no
IP=192.168.0.5
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1
DNS2=205.171.3.65
#
# Optional:
#specify time server host
#NTP=pool.ntp.org
#specify timezone
#TZ=PST8EDT
ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

wpa_supplicant.conf
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="SKY10444"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="********"
}

Does this look correct.
i have read that the PSK has to be in ascii is this correct?
also read a few posts up that the line:

wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf
should be:

wpa_supplicant -B w -D wext -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf

is this correct?
is the sda1 bit right or does it depend which port i have plugged my flashdisk in?
i have seen that you get get a message.txt file appear detailing whats going on. where does this appear? do i have to enable anything to get this or does it appear automatically?

thanks

- kebabinho

Title: Re: *experimental* wireless usb support package
Post by: Skye on June 05, 2009, 11:19:11 AM
Dear friends,

my box is online  ;D Thanks to your contributions to this thread. I'm using an MSI US54EX (802.11g) which I bought for 14,99€. It's based on rt73.

I'm running WDLXTV-05.3.2 with wireless-mod.app 0.3 and the log-saver.app.bin for logging.

My net.config looks like this:
Code: [Select]
ifconfig rausb0 up
# iwlist rausb0 scanning > /tmp/mnt/sda1/iwlist_scan.txt
wpa_supplicant -B w -D ralink -i rausb0 -c /tmp/mnt/sda1/wpa_supplicant.conf
iwlist rausb0 scanning > /tmp/mnt/sda1/iwlist_scan2.txt
sleep 5
HOST=wdtv
DHCP=yes

And the wpa_supplicant.conf is like this:
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="<your essid>"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
proto=RSN
pairwise=CCMP TKIP
key_mgmt=WPA-PSK
psk="<your pass>"
}

I run WPA2 with AES encryption on a dd-wrt router.

Hope this helps somebody. Now I need to learn about getting my drives linked to the box ::)

Skye
Title: Re: *experimental* wireless usb support package
Post by: Valenrotpunk on June 07, 2009, 05:36:22 AM
Thank you very much Nick 61

I have achived to connect wdtv with your script.

I have used hanewin nfs to share folder from pc but I can't play any film (avi, mkv 720p) more than 4 minutes, then wdtv return to main menu...I don't understand why becauser I can see photos and ear music without problems.

Anybody know what may be the problem?

Thank you for your great help.
Title: Re: *experimental* wireless usb support package
Post by: nfshp253 on June 11, 2009, 06:34:56 AM
Is the RT3070-based EnGenius EUB-9703 supported? Is there also any step-by-step guide with pictures to help noobies like me install this thing?
Title: Re: *experimental* wireless usb support package
Post by: atlbuzz on June 11, 2009, 01:43:00 PM
I am trying to get wireless working on my WDTV and will appreciate your help.

I am running:
1.02.07_B-RAD.CC_WDLXTV-0.5.3.2
opt.bin-0.2
core-extras.app.bin
wireless-mod.app_0.0.3_zorander

I have a Encore ENUWI-G2 802.11g wireless usb adapter which is "RTL8187B" based. I know this because when I plug it into a Windows machine, it is recognized as a "RTL8187B_WLAN" device.

I have gone through a lot of these forums and am lost now.
My net.config is
Code: [Select]
ifconfig rausb0 up
# iwlist rausb0 scanning > /tmp/mnt/sda1/iwlist_scan.txt
wpa_supplicant -Bw -Dralink -i rausb0 -c /tmp/mnt/sda1/wpa_supplicant.conf
iwlist rausb0 scanning > /tmp/mnt/sda1/iwlist_scan2.txt
sleep=5
HOST=wdtv
DHCP=yes

My wpa_supplicant.conf is
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="<my_ssid>"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
proto=RSN
pairwise=CCMP TKIP
key_mgmt=WPA-PSK
psk="<my_wpa2_key>"
}

I still get no-IP. Kindly advice if I am missing something? Is the "RTL8187B" chipset supported by the wireless-mod-0.0.3?
Title: Re: *experimental* wireless usb support package
Post by: rataweb on June 12, 2009, 02:50:27 AM
My DWL-122 is a PRISM2 model.

I've the same... Any solution???

Thanks.

Title: Re: *experimental* wireless usb support package
Post by: smartP on June 12, 2009, 07:24:02 PM
Is the RT3070-based EnGenius EUB-9703 supported? Is there also any step-by-step guide with pictures to help noobies like me install this thing?

I've just add the rt3070 driver to my app.bin, see http://wdtvforum.com/main/index.php?topic=1029.0
Title: Re: *experimental* wireless usb support package
Post by: Xinot on June 19, 2009, 02:35:16 AM
This thread is so confusing..  :-\

I have
-wdtvhd
-ipod formatted to fat32
-usb wlan Zyxel ZyAir G-220 = Zydas 1211/1211b vid_0586 pid_3401

I need to put WDLXTV 0.x.x.x files + wireless-mod.app.bin to my usb drive (ipod) ?
Need to make changes to net.config file and make file called wpa_supplicant.conf ?
Next i flash WDLXTV 0.x.x.x to my WD (with modded wdtv.ver) ?

Is this correct?

Next i put my wlan stick to wd and boot it up with usb drive (ipod) and it should work ?

If this is correct, what is working combination of WDLXTV + wireless-mod, and what changes i need to make in net.config and wpa_supplicant.conf with this Zydas 1211/1211b?

Thank You
Xinot

edit:with everything i have tried this far i always see same IP in WD. 192.168.0.102 Why is this?
Tried WDLXTV 0.5.2 & 0.5.3.2 & ext3-boot 0.9.2 with wireless-mod.app.bin 0.0.1 to 0.0.3
DHCP enabled or not every time wlan stick is "running" theres same IP 192.168.0.102
Title: Re: *experimental* wireless usb support package
Post by: FVD on June 19, 2009, 05:53:48 AM
copy log-saver.app.bin to your pen drive

To get the message.txt dmsg.txt and system.txt files that will help to check the IP, the mask and other errors.

good luck
Title: Re: *experimental* wireless usb support package
Post by: Xinot on June 19, 2009, 09:13:17 AM
 ;D It's working now!  ;D

1. I started from beginning again, and flashed official firmware 1.02.07, did hard reset & restored factory settings via OSD.
2. Downloaded ext-boot 0.9.2 (http://wdtvforum.com/main/index.php?topic=453.0) and extracted it to my fat32 formatted usb drive.
3. Connected usb drive to wd when running and updated firmware as it ask to do.
4. After boot wdtv just stay scanning my usb drive, but i did turn media library setting off until it stop scanning and after this turned library on again and scan was done ok in few seconds.
5. I did turn wdtv off via remote, and unplugged power cord.
6. I uploaded wireless-mod 0.3 (http://wdtvforum.com/main/index.php?topic=59.msg309#msg309) and extracted it to usb drive.
7. Made needed changes to net.config file in usb drive and made new file named wpa_supplicant.conf there too (see below)
8. Plugged my Zyxel ZyAir G-220 (Zydas 1211/1211b vid:0586 pid:3401) usb wlan stick and usb drive to wd and plugged power cord in.
9. Booted up with working wlan and correct IP with WPA

My net.config is
Code: [Select]
##Network configuration file
#Hostname
HOST=wd_tv_hd
#MTU=9000
#Dynamic IP
DHCP=no
#Static IP
IP=192.168.0.150
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1
#DNS2=205.171.3.65
#NTP=pool.ntp.org
ifconfig $MDEV up
wpa_supplicant -Bw -D otus -i$MDEV -c/boot/wpa_supplicant.conf
sleep=5

My wpa_supplicant.conf is
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="dlink"
#uncomment next line if your ap doesn't broadcast ssid
scan_ssid=1
key_mgmt=WPA-PSK
psk="password_here"
}

Now have to test some more.  ;)
Title: Re: *experimental* wireless usb support package
Post by: FVD on June 19, 2009, 09:21:04 AM
Good for you!!!
Title: Re: *experimental* wireless usb support package
Post by: Spartan on June 21, 2009, 01:23:43 PM
I can use some help on this one.  
After quite a bit of experimentation I finally got this going with the following issues:
1. It takes up to 2 or 3 power cycles to work each time.
2. I am able to NFS map my NAS successfully and be able navigate and play videos.
2. After some time of viewing a video I lose the remote Stop, FF, RW buttons functionality but back button works and I can start another video.  
3. My NFS mappings are retained by content disappears overnight, requiring a reboot.

I would appreciate any insight to this.

Environment:
SunDisk 4GB flash boot storage
Hawking HWUG1 wireless dongle (RT73 based)
Latest Zorander firmware with the latest wireless.mod

My net.config:
sleep=5
SUPPRESS_OTHERS=yes
HOST=wdtv2
DHCP=yes
sleep=5
ifconfig rausb0 up
slep=5
wpa_supplicant -B w -D ralink -i rausb0 -c /boot/wpa_supplicant.conf
sleep=5
NTP=0.north-america.pool.ntp.org
TZ=EST


my wpa_supplicant.conf:
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="<my SSID>"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
proto=RSN
pairwise=CCMP TKIP
key_mgmt=WPA-PSK
psk="<my pass>"
}

my boot directory:

-rwxr-xr-x    1 root     root         5716 Apr 24 07:06 Changelog
-rwxr-xr-x    1 root     root      5242880 May 27 02:29 core-extras.app.bin
-rwxr-xr-x    1 root     root         4096 Jun 20 01:12 log-saver.app.bin
-rwxr-xr-x    1 root     root       185264 Jan  1  2000 messages.txt
-rwxr-xr-x    1 root     root          215 Jan  1  2000 net.config
-rwxr-xr-x    1 root     root          692 Jun 21 00:51 net.mounts
drwxr-xr-x    2 root     root         4096 Jan  1  2000 pcha110
-rwxr-xr-x    1 root     root     67108864 Apr 24 07:07 root.bin
-rwxr-xr-x    1 root     root       151584 Mar 27 09:20 wdtv.bin
-rwxr-xr-x    1 root     root           54 Jun 20 03:47 wdtv.ver
-rwxr-xr-x    1 root     root      2420736 Jun 19 23:14 wireless-mod.app.bin
-rwxr-xr-x    1 root     root          228 Jun 21 00:51 wpa_supplicant.conf
drwxr-xr-x    2 root     root         4096 Jun 19 23:48 www
Title: Re: *experimental* wireless usb support package
Post by: Senseohasser on June 23, 2009, 03:14:21 AM
Did anybody get a Realtek RTL8187 to work?  :P
Title: Re: *experimental* wireless usb support package
Post by: Shiny on June 26, 2009, 12:26:19 PM
The wiki lists a Fritz! WLAN USB, did anyone get a Fritz! WLAN stick to work ?


Title: Re: *experimental* wireless usb support package
Post by: cionci on June 27, 2009, 01:12:25 AM
The wiki lists a Fritz! WLAN USB, did anyone get a Fritz! WLAN stick to work ?
The list is not exaustive. If a stick is listed with a name in the list is not assured it works. Many vendors sell sticks based on various chipsets under the same stick name.
So to be sure that a stick is supported you must identify vendor id and product id that should match one in the list below.
http://pl.wiki.wdtv.org/doku.php?id=wlanusb

To display ids: download a linux live distro (Ubuntu, puppy, ...), start from cd-rom, open a console and type:

lsusb

You'll have a list of product names and ids of all usb connected devices.
This is how vendor and product ids are displayed: 04b8:010b
Title: Re: *experimental* wireless usb support package
Post by: cookje on June 27, 2009, 01:55:53 AM
I've installed WDlxTV, took a wireless stick (WL-608, has 2870 chipset) and put on wireless-mod.app.bin, together with http://pastebin.ca/1475493 and http://pastebin.ca/1475496. Though this, it doesn't give any ip, and the logs keep clear, while log-saver.app.bin has been installed. Somebody got wise advise?

My homedir looks like

(http://i44.tinypic.com/2vwss3p.jpg)
Title: Re: *experimental* wireless usb support package
Post by: cionci on June 27, 2009, 01:56:55 AM
Read above...
Edit: sorry I didn't notice it has an rt2870. You should ask to who compiled 2870 module if product id is supported by module.
Title: Re: *experimental* wireless usb support package
Post by: cookje on June 27, 2009, 02:00:12 AM
Read above...

But although my stick doens't stand litterly on the list, my WDTV seems to don't see the app.bin files, what is required at least I suggest ;)

When fixed, I could look further for getting my stick compatible :)

/edit: Ah, I see... will hope my id already is in the driver, or it can be added. But first that other problem.
Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 28, 2009, 10:29:55 PM
Hi All

I am looking at getting the Dlink DWA-120, but my suppliers says he has no way of telling me what chipset is in there, I really dont wanna buy the wrong one..again :-[
How can I tell if this will be supported, as I have also been unable to find any info regarding the chipset for this on the net

Thanks!!
Title: Re: *experimental* wireless usb support package
Post by: cionci on June 29, 2009, 12:10:13 AM
Look at the post I wrote above, to be sure that a device is supported you must get vendor and product ids and then ids must be in one of these lists:
- wireless-mod-rt.app.bin supported devices are at the end of forst post (http://wdtvforum.com/main/index.php?topic=1029.0)
- supported device of wireless-mod app.bin released by b-rad and zorander (http://pl.wiki.wdtv.org/doku.php?id=wlanusb)
Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 29, 2009, 12:50:26 AM
Hi

Thanks for the reply, yeh i have been going thru that list, but it does not seem I can get the id's without going and purchasing the hardware. As the hardware sites do not show that type of info.
Title: Re: *experimental* wireless usb support package
Post by: cionci on June 29, 2009, 01:03:16 AM
Here they are:

Bus 003 Device 003: ID 07d1:3a0d D-Link System

Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 29, 2009, 01:13:09 AM
OK thanks

I see that PID is not in the list, so guess it wont work then...thanks!!
Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 30, 2009, 06:00:50 AM
Hi

Just got a SMCWUSBS-N2. Seems like the device is loading ok according to the messages.txt, but continuously says "channel is out of range". I am using the wireless-mod 0.3 of Zorander.

If someone could shed some light that would be awesome, this is my second usb wifi dongle now :)

Thank you
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on June 30, 2009, 10:43:15 AM
I am starting to pull my hair out by now...

I am using WDLXTV 0.5.5 and the zorander's wireless-mod.app.bin. My WIFI USB dongle is Sagem XG760A / zd1211 / vid 079b / pid 004a ( SUPPORTED, as stated on wiki ). It is recognized on boot, and considering messages.txt, loading correctly as eth0.

net.config:
HOST=wdtv_hd
DHCP=yes
ifconfig eth0 up
iwconfig eth0 essid WDTV
sleep 5

WDTV simply refuses to give me an IP address!

P.S. I have attached all the .txt files that are the result of using zorander's wireless-mod.app.bin with WDLXTV 0.5.5 firmware.
Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 30, 2009, 12:07:34 PM
Hey Frosty
Yeh looks like ur driver loaded ok, try a static ip. Your router is set to open at the moment right?
I used the wireless-mod-0.3-sebmod.zip and that sorted me out, although I had to just configure the RT2870STA.dat that is was asking for
Can u let ur messages grow for a bit, just wanna see happens.

Be strong, took me 3 days :)
Title: Re: *experimental* wireless usb support package
Post by: alex_ts on June 30, 2009, 12:16:49 PM
I have DLINK-140 WIFI module. Sometimes i am getting WDTV connect to my network, but sometimes it just connectes to someone elses open network. How can I make sure that my WDTV will connect to my Wifi network only?
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on June 30, 2009, 12:19:40 PM
Yeh looks like ur driver loaded ok, try a static ip. Your router is set to open at the moment right?

Believe me, I am at the end of my rope here... I already tried a static ip, but it didn't work.

My laptop WIFI enabled, and I am using my laptop's wifi card to create a completely open, no encryption AD-HOC connection ( laptop ad-hoc network SSID is WDTV, and I am trying to connect to it with my WDTV, like shown in net.config ), but it is impossible.

No IP from WDTV in any case I tried, and it does not connect to my PC at all, no matter how long I waited.

Please, understand that I am so irritated with the WDTV, I am just looking for a wall to smash it in.
Title: Re: *experimental* wireless usb support package
Post by: L3atherface on June 30, 2009, 12:38:34 PM
Frosty

What is the ip of ur laptop? How are u wanting to give ur WDTV an address, without DHCP, not too familiar with ad-hoc windows lameness
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on June 30, 2009, 03:23:06 PM
Well, I am trying to enable ad-hoc on the WDTV with this net.config, but I have some problems:

HOST=wdtv
group=workgroup
iwconfig eth0 mode ad-hoc channel auto rate auto essid Test
iwconfig commit
ifconfig eth0 up
DHCP=no
IP=192.168.1.123
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1

Anyone care to explain how they got ad-hoc working on the wdtv?
Title: Re: *experimental* wireless usb support package
Post by: LaurentG on June 30, 2009, 03:42:47 PM
Well, I am trying to enable ad-hoc on the WDTV with this net.config, but I have some problems:

HOST=wdtv
group=workgroup
iwconfig eth0 mode ad-hoc channel auto rate auto essid Test
iwconfig commit
ifconfig eth0 up
DHCP=no
IP=192.168.1.123
GW=192.168.0.1
NM=255.255.255.0
DNS1=192.168.0.1

Anyone care to explain how they got ad-hoc working on the wdtv?

One first problem in your config is that your command "ifconfig ..." should be bofore your command "iwconfig ...". And you could need to add command "sleep 3" after the "ifconfig".

It takes me a very long time before having a working and stable wifi connection in ad-hoc mode. My main problem was that the required module (rt73) was not loaded. So I adjusted the wireless app.bin...

I could advice, as you have WDLXTV firmware, to use the wireless app.bin provided by b-rad. I am not sure but it could be important.
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 01, 2009, 01:09:49 AM
ifconfig is before iwconfig, i just mistyped in the post :D

And, I also tried with all the sleeps possible ( 2, 5, 10 ), with b-rad's and zorander's wireless, but nothing works like it should. Even if it does, it's not stable and reliable. Simply, not worth the trouble. I was trying to enable wireless on my WDTV as to be able to use my smartphone or laptop to connect to it and delete, rename or upload a few things via FTP when needed... But after the whole day of tinkering, nothing. I give up. And another thing, WDTV with WDLXTV only boots with a 2GB USB stick, and it hangs with a 320GB WD Passport with a 2GB FAT32 partition.
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 01, 2009, 04:25:02 AM
Well... just couldn't give it up that easily...

Flashed ext3 boot 0.9.2, set up my net.config ( WEP ) and connected to my router. I can telnet to the WDTV and access my USB stick via FTP.

Only problem is the transfer rate is VERY slow and my WDTV WIFI crashes. Any way to solve that?

net.config
HOST=WDTV
group=WORKGROUP
ifconfig eth0 up
sleep 5
iwconfig eth0 essid test key s:testicle
sleep 5
DHCP=no
IP=192.168.1.35
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
sleep 5

As for messages.txt, there is a problem:

Jan  1 00:06:43 wdtv user.err kernel: 1211_readl failed for 5 attempts...Very Serious
Jan  1 00:06:44 wdtv user.info kernel: We are trapped in zd_SigProcess
... snip ...
Jan  1 00:05:06 wdtv user.warn kernel: ZD1211_TX_BUSY is locked over 5 seconds
Jan  1 00:05:06 wdtv user.warn kernel: jiffies = 6061, lastSetBusy = -15839, HZ=1000
...snip, snip, snipp...
Jan  1 00:11:29 WDTV user.info kernel: NETDEV WATCHDOG: eth0: transmit timed out
Jan  1 00:11:29 WDTV user.warn kernel: eth0: Tx timed out.
Jan  1 00:11:29 WDTV user.warn kernel: We are going to usb_kill_urb @ kevent
Jan  1 00:11:29 WDTV user.err kernel: Tx status: -2error in tx submit urb: -1Clear Tx Busy
Jan  1 00:11:29 WDTV user.warn kernel: error in tx submit urb: -1Clear Tx Busy
Jan  1 00:11:49 WDTV user.info kernel: NETDEV WATCHDOG: eth0: transmit timed out
Jan  1 00:11:49 WDTV user.warn kernel: eth0: Tx timed out.

I think that those are the lines that indicate my crashing problem with the Zydas... anyone has a solution? Please, someone take a look at this! I think that there's a problem with the 1211 driver in the ext3boot or wireless-mod.app
Title: Re: *experimental* wireless usb support package
Post by: skypeman on July 01, 2009, 08:52:32 AM
try this:

download the wdtv compiled version from here: http://www.mediafire.com/file/mxij3kfgxjd/zd1211.zip
put the zd1211.ko and zd1211b.ko on your stick.

Code: [Select]
host=wdtv
MTU=1452
insmod /boot/zd1211.ko
blacklist zd1211b
DHCP=no
IP=192.168.2.40
GW=192.168.2.1
NM=255.255.255.0
DNS1=192.168.2.1
DNS2=192.168.2.1
ifconfig $MDEV up
iwconfig $MDEV essid whatever key s:yourasciiikey
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 01, 2009, 10:28:38 AM
THANKS!  ;D ;D ;D Gonna try this right now! AFAIK, this is the latest compiled 1211 driver? NICE, ME LIKE!
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 01, 2009, 10:52:58 AM
It certainly works!

Bend over so I can kiss your royal a$$ :D ! I hail and salute you, skypeman!

I can FTP, Telnet and Windows Network access my WDTV over the WIFI ( first FAT32 and second NTFS partition ).
But, when I use Windows Network / FTP and try to copy/rename something on my WDTV USB hard disk NTFS partition, it says that I have no permission ( see picture below ).
(http://www.imagesforme.com/out.php/t570764_picture.jpg) (http://www.imagesforme.com/show.php/570764_picture.jpg)

How to modify your NTFS partition on the WDTV:

Create a file on your PC named "S50custommounts" or use nano and create it directy on the WDTV.

And type the following in it:

#!/bin/sh

mkdir -p /mnt/usb/USB1/ntfsdirname

mount -t ntfs-3g -o iocharset=utf8 /dev/sda2 /mnt/usb/USB1/ntfsdirname


Change "ntfsdirname" to anything you want. The /dev/sda2 is the second partition in USB1 ( your NTFS partition ). If the NTFS partition is another one, change it to its correct unix name ( like sda1, or sda 3 - you get it ).

Exit the text editor. Use DOS2UNIX to convert it to Unix format. Copy it to etc/init.d folder via FTP.

Next:
1) telnet to the wdtv
2) cd /etc/init.d
4) chmod 755 S50custommounts
5) reboot


It works after reboot. Your writable NTFS folder can be found at mnt/usb/USB1. Fully writeable. YES!

THANKS TO MIKE2K8.
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 02, 2009, 04:52:22 AM
Looking through messages.txt, it seems opt.bin mounts...

Jan  1 00:00:31 DMAX user.notice root: INIT: mounting app binaries...
Jan  1 00:01:22 DMAX user.notice root: Mounting opt.bin at /opt

... but a quick FTP check shows otherwise. There is no opt folder anywhere, no ipkg.sh, no nothing. ipkg update does not work.

Solution for the manual Optware mount, for those whose opt.bin does not mount automatically.

mkdir /opt
mount -o loop /tmp/media/usb/USB1/<your usb unix name>/opt.bin /opt
wait a bit
type "mount"
if there's a /dev/loop0/ on /opt... than you're game!

start ipkg update this way ( from root, telnet ):
/opt/bin/ipkg update

download nano this way ( from root, telnet ):
/opt/bin/ipkg nano

start apps like this EXAMPLE ( from root, telnet ):
/opt/bin/nano fileiwanttoedit
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 02, 2009, 09:00:07 AM
Zorander, there seems to be a problem automounting opt.bin in 0.9.2... I don't know what to say otherwise, especially after extensive testing and reflashing...
Title: Re: *experimental* wireless usb support package
Post by: Srezma on July 04, 2009, 01:10:01 PM
Hi, there...

Is there someone who know how to configure net.config for JAHT WN-4054U - I assume it uses RT73 chip?

I am spending days with WD HDTV to get it on-line but nothing:

I have DHCP and WEP-PSK; My configuration is:
1.02.10_B-RAD.CC_WDLXTV-0.5.5
opt.bin-0.2
wireless-mod.app_0.0.3_zorander

net configuration:

sleep=1
SUPPRESS_OTHERS=yes
HOST=wd_tv
MTU=9000
DHCP=yes
sleep=1
ifconfig eth0 up
slep=1
wpa_supplicant -B w -D wext -i eth0 -c /boot/wpa_supplicant.conf
sleep=5
NTP=0.pool.ntp.org
sleep=1

and WPA supplicant configuration

ctrl_interface=/tmp/wpa_supplicant
network={
ssid="MY-NAME"
#uncomment next line if your ap doesn't broadcast ssid
scan_ssid=1
key_mgmt=WPA-PSK
psk="MY-CODE"
}

Has someone any Idea?

I am newby...

Thx.



Title: Re: *experimental* wireless usb support package
Post by: TON on July 05, 2009, 01:42:21 AM
Try to replace eth0 with $MDEV. My D-Link DWA110 dongle is also rt73-based and the interface name is rausb0. $MDEV should work in all cases.
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 05, 2009, 02:50:17 AM
Hi, there...

Hi. Check this out:
http://wdtvforum.com/main/index.php?topic=1029.0
Title: Re: *experimental* wireless usb support package
Post by: umby800 on July 05, 2009, 12:41:27 PM
Hi, cionci (sorry for my poooooooooor english)

The dongle SITECOM WL-608 work with debian squeeze (and now with WDTW).

http://rapidshare.com/files/252367558/wireless-mod-rt2070.app.bin.htm (http://rapidshare.com/files/252367558/wireless-mod-rt2070.app.bin.htm)

The chip il a RT2070L (i have open the dongle)

1 - Download the driver and untar/unzip:
http://www.ralinktech.com.tw/data/drivers/2009_0525_RT3070_Linux_STA_v2.1.1.0.bz2

and modify the file

os/linux/usb_main_dev.c


adding the line

{USB_DEVICE(0x0DF6,0x003F)}, /* Ralink 2070 */

after

{USB_DEVICE(0x0DB0,0x3820)}, /* Ralink 3070 */
{USB_DEVICE(0x0DF6,0x003E)}, /* Sitecom 3070 */
{USB_DEVICE(0x0DF6,0x0042)}, /* Sitecom 3072 */

and save.

Modify the file

os/linux/config.mk

#ifdef WPA_SUPPLICANT_SUPPORT
# Support Wpa_Supplicant
HAS_WPA_SUPPLICANT=n (to replace n with y)
#endif // WPA_SUPPLICANT_SUPPORT //

#ifdef NATIVE_WPA_SUPPLICANT_SUPPORT
# Support Native WpaSupplicant for Network Maganger
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n (to replace n with y)
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //

and save.

make

make install

mkdir /etc/Wireless/RT2870STA

cp /etc/Wireless/RT3070STA/RT3070STA.dat /etc/Wireless/RT2870STA.dat

modprobe rt3070sta

ifconfig ra0 192.168.0.3 up (for fixed IP)

Et voilà, works !!


Title: Re: *experimental* wireless usb support package
Post by: milokur on July 11, 2009, 05:04:39 AM
I have Linksys WUSB54GC usb dongle. Inside is RT2571 chip. Any chances to work???
Title: Re: *experimental* wireless usb support package
Post by: TON on July 11, 2009, 10:27:14 AM
Ok, I've got too tired of fighting my D-Link DWA110 dongle (rt73 based). It used to loose connectivity every 10-20 hours and I could not make it work stable especially with high network loads.

So I bought myself another dongle, Zyxel G-202, zydas-based. It has been running torrents for more than 24 hours now and I tried to use it as much as possible during this time and it is still working ;D

I do not know if it is possible to make rt73 work in my case (I use WPA for encryption, probably this has something to do with the instability). G202 works in this configuration without any problems.

I am using a driver from Zorander's wireless pack.

I hope now all my troubles with networking are finally gone ;D!
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on July 13, 2009, 12:22:11 PM
All I can say about Zydas based adapters is they are great, drivers are stable and everything works as it should. Plus that, dongles based on them are cheap as hell.
Title: Re: *experimental* wireless usb support package
Post by: aspas on July 14, 2009, 02:36:56 AM
Hello,

I'm using a GWL-122 with WPA-PSK and this package. Unfortunately, it looses its connection after a couple of hours of heavy-ish traffic (say, above ~150Kb/s). I can only keep it connected with less traffic.

When it looses connection, it signals that it's not associated any more and blinks its traffic light every now and then just like when it's searching for an AP.

Does any of you have any suggestion?

Is there any way of getting wpa_supplicant to log to a file when running as a deamon?

Here's my wpa_supplicant.conf:

#ctrl_interface=/boot/ctrl/wpa_supplicant -- disabled, otherwise it doesn't work
network={
  ssid="***"
  scan_ssid=1
  key_mgmt=WPA-PSK
  pairwise=TKIP
  group=TKIP
  psk="********"
}

And the relevant net.config lines:

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf

Thank you for any help!  :)
Title: Re: *experimental* wireless usb support package
Post by: cionci on July 14, 2009, 02:41:45 AM
I had the same issue on both RT73 dongles I've tried.

ctrl_interface=/boot/ctrl/wpa_supplicant

should be:

ctrl_interface=/tmp/wpa_supplicant

Have you tried this ? http://wdtvforum.com/main/index.php?topic=1029.0
Title: Re: *experimental* wireless usb support package
Post by: aspas on July 14, 2009, 05:39:03 AM
I had the same issue on both RT73 dongles I've tried.

ctrl_interface=/boot/ctrl/wpa_supplicant

should be:

ctrl_interface=/tmp/wpa_supplicant

Hummmm... I'll give it a try tonight when I get home.

You didn't find a solution to the problem, did you?

Have you tried this ? http://wdtvforum.com/main/index.php?topic=1029.0

I have. It exhibits the same behaviour, except that the dongle is left with no feedback whatsoever when it looses connection (no blinking leds).
Title: Re: *experimental* wireless usb support package
Post by: TON on July 14, 2009, 09:40:41 AM
I have changed my rt73-based dongle to Zydas-based one. Now I sleep well and it keeps working :D
Title: Re: *experimental* wireless usb support package
Post by: JPH on July 19, 2009, 01:03:13 AM
hello, the first thing i want to tell is thank you, with all the posts here i was able to connect my wdtv with the wireless adapter F5D8053v3 (RT2870STA). But i've noticed that i can't protect my network with any kind of wpa encryption WPAPSK, WPA2PSK AES or TKIP, each time the adapter can't connect and don't display it's IP (i'm in static, no DHCP). It works well in wep and without protection.  
 I try with wireless-mod-rt.app (1.2.4 i think and latest WDLXTV firmware)
 and my question is: is wpa_spplicant needed ? i tried almost everything in RT2870STA.dat without results.
  My RT2870STA.dat when i try to use wpa:

SSID=ABCDE
AuthMode=WPAPSK or WPA2PSK
EncrypType=TKIP or AES , i tried both
WPAPSK=hereismykey


Someone has any idea?
Title: Re: *experimental* wireless usb support package
Post by: netmen on July 24, 2009, 11:46:26 AM
Hello, people.
I need a help.
I have wireless dongle EDIMAX 7718UN.
If this device can work properly with WDTV ???

Tnx.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 24, 2009, 12:24:58 PM
Sorry for my Bad English i am German User!

Translate by Google
Hello!
I hope you can help me with my problem help.
I've read through all the pages, but either my English is so bad or I have not found.
I am no functioning wireless connection.
I write here at my settings.

Software & USB Pen:
Quote
WDlxTV 0.5.5
wireless-mod.app.bin (0.3)
log-saver.app.bin

WLAN Stick:
Quote
Chipset - zd1211
VID - 0ace
PID - 1215

net.config:
Quote
#
# Network configuration file
#You can override the hostname here:

HOST=wdtv
ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

# if you do not set a hostname,a random one is assigned.
# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.2.25
#GW=192.168.2.1
#NM=255.255.255.0
#DNS1=192.168.2.1
#DNS2=205.171.3.65

#
# Optional:  

#specify time server host
#NTP=pool.ntp.org

#specify timezone
#TZ=PST8EDT

wpa_supplicant.conf:
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Ganja-WLAN"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="*****"
}

Router:
Quote
WPA2-PSK
AES

dmesg.txt.0:
Code: [Select]
...
Loading wireless extentions module...
zd1201: Unknown symbol release_firmware
zd1201: Unknown symbol request_firmware
ZD1211B - version 2.19.2.9
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPROM Ver = 4810
Finish download Firmware. Ready to reboot
PA type: 0
PHYNEWLayout = 1
AiroHa AL2230RF
ieee80211_dirmcast_attach
OverWrite CR47 = 0x1C
zd1205_config: EEP(HWFeature)=0x500
AllowedChannel = 000107ff
Region:48
usbcore: registered new driver zd1211b
arusb - version 0.0.0.999
usbcore: registered new driver Otus
rtusb init --->
usbcore: registered new driver rt2870
usbcore: registered new driver rt73
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)

messages.txt.0:
Code: [Select]
...
Dec 31 16:00:50 WDTV-f7e46 user.notice root: wireless-mod app found
Dec 31 16:00:50 WDTV-f7e46 user.notice root: Mounting /tmp/mnt/sda1/wireless-mod.app.bin at /apps/wireless-mod
Dec 31 16:00:50 WDTV-f7e46 user.warn kernel: UDF-fs: No VRS found
Dec 31 16:00:51 WDTV-f7e46 user.notice root: adjusting LIBPATH
Dec 31 16:00:51 WDTV-f7e46 user.notice root: adjusting PATH
Dec 31 16:00:52 WDTV-f7e46 user.notice root: Path set to /apps/wireless-mod/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Dec 31 16:00:58 WDTV-f7e46 user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:58 WDTV-f7e46 user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Dec 31 16:00:58 WDTV-f7e46 user.info kernel: usbcore: registered new driver asix
Dec 31 16:00:58 WDTV-f7e46 user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Dec 31 16:00:58 WDTV-f7e46 user.info kernel: usbcore: registered new driver dm9601
Dec 31 16:00:58 WDTV-f7e46 user.info kernel: usbcore: registered new driver kaweth
Dec 31 16:00:59 WDTV-f7e46 user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Dec 31 16:00:59 WDTV-f7e46 user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Dec 31 16:00:59 WDTV-f7e46 user.info kernel: usbcore: registered new driver pegasus
Dec 31 16:00:59 WDTV-f7e46 user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Dec 31 16:00:59 WDTV-f7e46 user.info kernel: usbcore: registered new driver rtl8150
Dec 31 16:01:00 WDTV-f7e46 user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Dec 31 16:01:00 WDTV-f7e46 user.info kernel: usbcore: registered new driver cdc_ether
Dec 31 16:01:00 WDTV-f7e46 user.info kernel: usbcore: registered new driver catc
Dec 31 16:01:00 WDTV-f7e46 user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Dec 31 16:01:00 WDTV-f7e46 user.info kernel: usbcore: registered new driver cdc_subset
Dec 31 16:01:00 WDTV-f7e46 user.info kernel: usbcore: registered new driver net1080
Dec 31 16:01:01 WDTV-f7e46 user.info kernel: usbcore: registered new driver plusb
Dec 31 16:01:01 WDTV-f7e46 user.info kernel: usbcore: registered new driver rndis_host
Dec 31 16:01:01 WDTV-f7e46 user.info kernel: usbcore: registered new driver gl620a
Dec 31 16:01:02 WDTV-f7e46 user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Dec 31 16:01:02 WDTV-f7e46 user.info kernel: Loading wireless extentions module...
Dec 31 16:01:03 WDTV-f7e46 user.warn kernel: zd1201: Unknown symbol release_firmware
Dec 31 16:01:03 WDTV-f7e46 user.warn kernel: zd1201: Unknown symbol request_firmware
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: ZD1211B - version 2.19.2.9
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: vendor_id = 0ace
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: product_id = 1215
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: USB 2.0 Host
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: Release Ver = 4810
Dec 31 16:01:03 WDTV-f7e46 user.notice kernel: EEPROM Ver = 4810
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: Finish download Firmware. Ready to reboot
Dec 31 16:01:04 WDTV-f7e46 user.err kernel: PA type: 0
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: PHYNEWLayout = 1
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: AiroHa AL2230RF
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: ieee80211_dirmcast_attach
Dec 31 16:01:04 WDTV-f7e46 user.debug kernel: OverWrite CR47 = 0x1C
Dec 31 16:01:04 WDTV-f7e46 user.debug kernel: zd1205_config: EEP(HWFeature)=0x500
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: AllowedChannel = 000107ff
Dec 31 16:01:04 WDTV-f7e46 user.warn kernel: Region:48
Dec 31 16:01:04 WDTV-f7e46 user.info kernel: usbcore: registered new driver zd1211b
Dec 31 16:01:04 WDTV-f7e46 user.notice root: net.agent:  Called for eth0
Dec 31 16:01:04 WDTV-f7e46 user.notice root: net.agent: No IP provided, doing DHCP
Dec 31 16:01:07 WDTV-f7e46 user.notice kernel: arusb - version 0.0.0.999
Dec 31 16:01:07 WDTV-f7e46 user.info kernel: usbcore: registered new driver Otus
Dec 31 16:01:08 WDTV-f7e46 user.warn kernel: rtusb init --->
Dec 31 16:01:08 WDTV-f7e46 user.info kernel: usbcore: registered new driver rt2870
Dec 31 16:01:09 WDTV-f7e46 user.info kernel: usbcore: registered new driver rt73
Dec 31 16:01:09 WDTV-f7e46 daemon.info utelnetd[1435]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Dec 31 16:01:10 WDTV-f7e46 user.notice root: Switching to default 120x180 thumb view
Dec 31 16:01:12 WDTV-f7e46 user.debug kernel: ir: Enable NEC decoder (0x00000000)
Dec 31 16:01:12 WDTV-f7e46 user.debug kernel: ir: Enable RC5 decoder (0x00000000)

system.txt.0:
Code: [Select]
/dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
/dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
/dev/sda1: UUID="AC63-ADF9" TYPE="vfat"
/dev/loop0: LABEL="log-saver" TYPE="cramfs"
/dev/loop1: LABEL="wmod-003" TYPE="cramfs"
======================================
Displaying detected USB devices...
 [0781:5151] 1-1( 2.00,480m) Cruzer Micro/15356002F4D18735
 [05e3:0608] 1-2( 2.00,480m) USB2.0 Hub
 [0ace:1215] 1-2.3( 2.00,480m) USB2.0 WLAN
 [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
 [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
======================================
major minor  #blocks  name

   7     0          4 loop0
   7     1       2364 loop1
  31     0      16384 mtdblock0
  31     1        384 mtdblock1
  31     2       2176 mtdblock2
  31     3      13568 mtdblock3
  31     4        128 mtdblock4
  31     5        128 mtdblock5
   8     0    7847935 sda
   8     1    7839698 sda1
======================================
rootfs / rootfs rw 0 0
proc /proc proc rw,nodiratime 0 0
sysfs /sys sysfs rw 0 0
/dev/mtdblock3 / cramfs ro 0 0
none /proc proc rw,nodiratime 0 0
usb /proc/bus/usb usbfs rw 0 0
sysfs /sys sysfs rw 0 0
none /tmp tmpfs rw 0 0
none /etc/mdev.conf tmpfs rw 0 0
mdev /dev tmpfs rw 0 0
devpts /dev/pts devpts rw 0 0
/dev/sda1 /tmp/mnt/sda1 vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
none /apps tmpfs rw 0 0
/dev/loop0 /apps/log-saver cramfs ro 0 0
/dev/loop1 /apps/wireless-mod cramfs ro 0 0
none /osd/image/welcome_background_bg.jpg tmpfs rw 0 0
none /osd/image/screen_saver.png tmpfs rw 0 0
/dev/sda1 /tmp/media/usb/USB1/AC63-ADF9 vfat rw,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1 0 0
======================================
Module                  Size  Used by    Tainted: PF
rt73                  289040  0
rt2870sta             522448  0
arusb_lnx             450656  0
zd1211b               338256  0
wireless_ext            8240  4 rt73,rt2870sta,arusb_lnx,zd1211b
gl620a                  2448  0
rndis_host              3888  0
plusb                    752  0
net1080                 3808  0
cdc_subset              1184  0
catc                   11216  0
cdc_ether               2992  1 rndis_host
rtl8150                11200  0
pegasus                20448  0
mcs7830                 4496  0
kaweth                 15216  0
dm9601                 14320  0
asix                   18928  0
usbnet                 15728  8 gl620a,rndis_host,plusb,net1080,cdc_subset,cdc_ether,mcs7830,asix
mii                     3824  4 pegasus,mcs7830,asix,usbnet
loop                   13232  0
em8xxx                846784  8
proc_pipe            1064688  0
llad                   95648  9 em8xxx
sr_mod                 12672  0
cdrom                  35424  1 sr_mod

for help, I would be very grateful.

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 25, 2009, 01:54:28 AM
First of all try using '-Dotus' for Zydas-based dongle. It was the only setting that did work for me.

Second, IMHO there is no /boot directory in wdlxtv, something like /tmp/whatever should be used. I use Zorander's ext3-boot so I do not know the exact location. I believe you can easily find it on the forum.

Otherwise everything looks ok, the driver gets loaded and recognizes your dongle.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 25, 2009, 02:34:03 AM
I have again tested.

With open AP, the driver from Site 27 and this net.config
Quote
host=wdtv
MTU=1452
insmod /boot/zd1211b.ko
#blacklist zd1211b
#ifconfig $MDEV up
#wpa_supplicant -Bw -Dotus -i$MDEV -c/boot/wpa_supplicant.conf
ifconfig $MDEV up
iwconfig $MDEV essid Ganja-WLAN
DHCP=yes
#DHCP=no
#IP=192.168.2.118
#GW=192.168.2.1
#NM=255.255.255.0
#DNS1=192.168.2.1
#DNS2=192.168.2.1
#NTP=pool.ntp.org
#specify timezone
#TZ=PST8EDT

Thus do I get an IP and Telnet access to the box.
   
what do you mean with the text - > Second, IMHO there is no /boot directory in wdlxtv, something like /tmp/whatever should be used. net.confg or wpa_supplicant.conf

Thanx for Help

Steve

Title: Re: *experimental* wireless usb support package
Post by: netmen on July 25, 2009, 11:07:09 AM
Hi,
How can i see the log files ?
Where i need to turn it on ?
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 26, 2009, 02:42:27 AM
Hi,
How can i see the log files ?
Where i need to turn it on ?

you need the log-saver.app.bin in / on USB-Stick
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 26, 2009, 02:56:35 AM
Can anyone help me?

brad.cc write on Page 6
Quote
/boot doesn't exist in wdxltv.

Can it be something with the / boot settings in wpa_supplicant.conf or net.config not true? If so by what should I replace it? / tmp?

I do not connect with WEP and WPA encryption

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 26, 2009, 09:36:50 PM
Steve

Your wpa_supplicant line in net.config references a conf file in /boot directory. This directory does not exist in WDLXTV. You can either search this forum looking for the correct path or you can connect with the open network, telnet into your box and try to locate where the root directory of your usb stick gets mounted. I just remember it starts with /tmp.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 01:05:16 AM
I've already done when I open via telnet, and open AP gets hit on the box, the USB stick to / tmp mounted. I have the WPA supplicant is entered, no success.
Why do I get even with WEP encryption can not connect? Entry in the net.config is:

ifconfig $MDEV up
iwconfig $MDEV essid your_ap_name key "s:403122...121"

Thanx for help

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 27, 2009, 01:49:00 AM
Regarding WEP: try to insert 'sleep 5' between ifconfig and iwconfig lines. Sometimes the second call fails because the interface is not yet really up.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 02:00:20 AM
I have my WLAN stick with another Linux system tested.

Ubuntu works with my wireless connection, whether WPA/WPA2, WEP or open.

Steve
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 02:27:55 AM
Regarding WEP: try to insert 'sleep 5' between ifconfig and iwconfig lines. Sometimes the second call fails because the interface is not yet really up.

Thanks for the tip I will try the same tonight.

Steve
Title: Re: *experimental* wireless usb support package
Post by: mike2k8 on July 27, 2009, 10:36:56 AM
I'd like to post an alternative configuration for WPA/WPA2 for rt73 based dongles (tested on Linksys WUSB54GC). It could work on other dongles too (people are welcome to try and post the results).

This configuration doesn't use wpa_supplicant (and hence wpa_supplicant.conf is not needed). This hopefully releases some resources, and it *could* be more stable (need people to test it and comment it here).
These are the relevant lines in net.config (wpa_supplicant line must be removed or commented out if it exists).

Config for WPA2

Code: [Select]
ifconfig $MDEV up
sleep 2
iwpriv $MDEV set Networktype=Infra
iwpriv $MDEV set AuthMode=WPA2PSK
iwpriv $MDEV set EncryptType=AES
iwpriv $MDEV set SSID="MyEssidName"
iwpriv $MDEV set WPAPSK="my passphrase"
iwconfig $MDEV essid MyEssidName

Config for WPA

Code: [Select]
ifconfig $MDEV up
sleep 2
iwpriv $MDEV set Networktype=Infra
iwpriv $MDEV set AuthMode=WPAPSK
iwpriv $MDEV set EncryptType=TKIP
iwpriv $MDEV set SSID="MyEssidName"
iwpriv $MDEV set WPAPSK="my passphrase"
iwconfig $MDEV essid MyEssidName

It works because rt73 module has WPA functions built in, and so it doesn't need to rely on an external application (wpa_supplicant). Instead it uses standard linux wireless tools (iwpriv, iwconfig).

It could be a good idea if someone can add this to the wiki.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 10:48:50 AM
I have the whole thing with 64bit WEP encryption, and this configuration tested.
Quote
HOST=wdtv
MTU=1452
insmod /tmp/zd1211.ko
blacklist zd1211b


# WPA
#ifconfig $MDEV up
#sleep 5
#wpa_supplicant -Bw -Dwext -i$MDEV -c/tmp/wpa_supplicant.conf

# WEP
ifconfig $MDEV up
sleep 5
iwconfig $MDEV essid Ganja-WLAN key "s:24**1***00"

#open AP
#ifconfig $MDEV up
#iwconfig $MDEV essid Ganja-WLAN

#MTU=9000

DHCP=yes

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65


#NTP=pool.ntp.org


#TZ=PST8EDT
Unfortunately without success. There's no log to which I could post, which further helps?
   
There are also a wireless-mod-wdlxtv.app.bin.
What does it mean?   
Use the no one here similar configuration?

Quote
I'd like to post an alternative configuration for WPA/WPA2 for rt73 based dongles (tested on Linksys WUSB54GC). It could work on other dongles too (people are welcome to try and post the results).

This configuration doesn't use wpa_supplicant (and hence wpa_supplicant.conf is not needed). This hopefully releases some resources, and it *could* be more stable (need people to test it and comment it here).
These are the relevant lines in net.config (wpa_supplicant line must be removed or commented out if it exists).
   
Can I also use on my chipset, and if so then I need but the wireless-mod-rt.app.bin.

Is that correct?

Steve
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 12:25:49 PM
I again via telnet logged on my box to check where the USB stick is mounted. It is not written by me, such as / tmp but / tmp/mnt/sdb1 /.
I have the wpa_supplicant.conf with the command find / * | grep wpa_supplicant.conf found.

Have you used the net.config
Quote
OST=wdtv
MTU=1452
insmod /tmp/mnt/sdb1/zd1211.ko
blacklist zd1211b
ifconfig eth0 up
sleep 5
wpa_supplicant -Bw -Dwext -ieth0 -c/tmp/mnt/sdb1/wpa_supplicant.conf
DHCP=yes
   
unfortunately without success
I'm tired and go to bed.

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 27, 2009, 09:22:28 PM
Steve

Now that you have fixed the path to your wpa_supplicant.conf file please do not forget to change '-Dwext' to '-Dotus' in your net.config. I believe I mentioned it in some earlier message. Only the latter setting works with zydas-based dongles.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 27, 2009, 10:47:48 PM
Thanks, I've changed so much and tried because I have the most with the value-Dotus forgotten.    
I had had this set but the path to the wpa_supplicant.conf not restated.

In any case I am ever grateful for your help now.

Will keep trying tonight.

/EDIT
What is with the wireless-mod-wdlxtv.app.bin?

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 28, 2009, 03:08:45 AM
That might well be the point!!! ;D I do not use WDLXTV so I keep forgetting its differences from ext3-boot.

I remember Brad wrote some time ago you need to use wireless-mod-wdlxtv.app.bin with his mod. But again I do not have any experience with it though I believe it should roughly be the same (but the devil is always in the detais :D)
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 28, 2009, 05:32:13 AM
Do I have the wireless mod-wdlxtv.app AND the wireless mod.app or use just one.

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 28, 2009, 09:02:26 PM
Just wireless-mod-wdlxtv.app.bin.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 28, 2009, 09:36:57 PM
I have tried all possible combinations, with a wireless-mod-wdlxtv.app and without. With the wireless-mod-wdlxtv.app I get a firmware error.
I can post the log file tonight.

Steve
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 29, 2009, 09:47:54 AM
Have with the wireless-mod-wdlxtv.app.bin alone tested.

my messages.txt:
Quote
Dec 31 16:01:19 WDTV-68be0 user.info kernel: Loading wireless extentions module...
Dec 31 16:01:20 WDTV-68be0 user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 29, 2009, 10:24:23 AM
Is it really just two lines long? ???
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 29, 2009, 09:34:22 PM
Is it really just two lines long? ???


No.
I post this evening, the full text.

/EDIT
my messages (http://ganja.mine.nu/stuff/messages.txt)

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on July 30, 2009, 09:54:54 PM
Your messages.txt is not full. It stops at the most interesting part >:(. I can see the driver loading but whether it sees the dongle or not is torn off.
Title: Re: *experimental* wireless usb support package
Post by: Steve on July 30, 2009, 10:28:55 PM
Your messages.txt is not full. It stops at the most interesting part >:(. I can see the driver loading but whether it sees the dongle or not is torn off.

   
More I did not. This is the full messages.txt. See the messages.txt on Site 29 she is not longer.
I can post the full messages.txt from wireless-mod.app.bin tonight.

/EDIT
WEP messages (http://ganja.mine.nu/stuff/messages_wep.txt)
open AP messages (http://ganja.mine.nu/stuff/messages_op.txt)
WPA messages (http://ganja.mine.nu/stuff/messages_wpa.txt)
Steve
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 03, 2009, 12:46:21 AM
Has nobody an idea that I could still looking?

Steve
Title: Re: *experimental* wireless usb support package
Post by: leonardob on August 03, 2009, 07:36:46 PM
Hi people... today i got mi WDTV. I spent all the past week researching and reading abaut wlan hacks and wdtv. So i bought the D-Link 110 USB dongle... and i manage to make it work.

The problem is that i cant make it to get an IP addres... i tried bouth DHCP and fixed IP... here is my config:

Net.config
Quote
# Network configuration file
#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.
# attempt to set jumbo framesMTU=9000

Dynamic IP Configuration:DHCP=yes

## Static IP Configuration:  (only if not DHCP)
#DHCP=no
#IP=192.168.1.60
#GW=192.168.1.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65
## Optional:  
#specify time server host
#NTP=pool.ntp.org
#specify timezone
#TZ=PST8EDT

ifconfig $MDEV up
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf

wpa_supplicant.conf

Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Star Wars"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="23456789"
}

Mi wireless router is using WPA-TKIP
Mi IP range es 192.168.1.52 and bigger.

Title: Re: *experimental* wireless usb support package
Post by: TON on August 03, 2009, 09:09:51 PM
Has nobody an idea that I could still looking?
Steve

I think I am exhausted >:( I do not have much experience with WDLXTV. Since you can connect to an open network the problem is somehow related to your wpa_supplicant. Either the file cannot be found or some similar problem exists.

I can suggest just one more thing: redirect the output from your wpa_supplicant call to some text file like this:

wpa_supplicant -Bw -Dotus -ieth0 -c/tmp/mnt/sdb1/wpa_supplicant.conf > /tmp/mnt/sdb1/output.txt

This way you will be able to see the command output if it produces any.

Another thing to try is to connect to an open network, telnet to WDTV and then issue the above command manually. It will not connect but it should complain if anything is incorrect. I believe there is a way to start wpa_supplicant in non-daemon mode.

Title: Re: *experimental* wireless usb support package
Post by: Steve on August 03, 2009, 11:38:50 PM


Another thing to try is to connect to an open network, telnet to WDTV and then issue the above command manually. It will not connect but it should complain if anything is incorrect. I believe there is a way to start wpa_supplicant in non-daemon mode.


I make this with no Errors.   
But why does not even ne WEP connection.   
I think I should look at the software Zorander change.

Steve

Title: Re: *experimental* wireless usb support package
Post by: henno on August 05, 2009, 10:48:49 PM
Hi guys,

I sure hope someone would be able to assist me. I'm very new to this so please excuse me.

Yesterday for the first time I successfully upgraded my WDTV to WDLXTV-0.5.5 firmware. My aim is to give my WDTV network connectivity, so I also downloaded and placed wireless-mod-wdlxtv.app.bin in the root folder with an updated net.config, and wpa_supplicant.conf as per instructions at http://www.wdtvc.com/2009/04/06/how-to-config-wifi-usb-adapter-with-wd-tv/

Unfortunately I was unable to make any real progress. I googled, and searched this forum, however couldnt find any answers. Here's my setup:
Linksys Wireless Access Point [WPA-PSK - AES] - initially it was set on WPA2, so I tried setting it to normal WPA as well. DHCP enabled.
Belkin F5D7051 USB Wireless


I've come across a page that identifies the chipset.
http://forums.fedoraforum.org/showthread.php?t=210937

"Belkin F5D7051 USB wireless device is known to use the Broadcom 4320 USB chipset"

"To me, the most interesting thing about this thread is that three built-in Ralink driver modules had to be blacklisted before a wireless card with a Broadcom chipset would work with the rndis_wlan built-in driver module."

"... my belkin F5D7051 USB WiFi would fail miserably and even prevent the system from booting or running lsusb. This appeared to be down to conflicting drivers, I managed to fix this by blacklisting rt2500usb, rt2x00usb and rt2x00lib, and it now uses rndis_wlan."

Here's my net.config.

**********************************************************************************
#
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:

DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional: 

#specify time server host
#NTP=pool.ntp.org

#specify timezone
#TZ=PST8EDT

ifconfig $MDEV up
wpa_supplicant -Bw -Dralink -i$MDEV -c/boot/wpa_supplicant.conf

**********************************************************************************
NOTE: I tried the -Dwext setting as well.

and my wpa_supplicant.conf

**********************************************************************************
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="badokunAP"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="81Yyyyyyyyyy"
}
**********************************************************************************

here's my log entries... (I've placed them on a server, so this post does not get too long)

http://www.3ddiagnostic.co.za/other/messages.txt
http://www.3ddiagnostic.co.za/other/system.txt
http://www.3ddiagnostic.co.za/other/dmesg.txt
Title: Re: *experimental* wireless usb support package
Post by: henno on August 06, 2009, 10:05:05 PM
Just to follow up on my previous post. I found this article (http://kahrn.wordpress.com/2009/05/27/belkin-f5d7051-usb-wifi-and-linux/)

Belkin F5D7051 USB WiFi and Linux

These methods have been tested under Fedora, Ubuntu and BackTrack 4. All of the following should work in almost any linux distribution to get a Belkin F5D7051 (or possibly similar device) working in Linux for WiFi access.

By default the F5D7051 conflicts with 3 drivers (the rt* set of drivers). These drivers must be disabled, rndis_wlan must be loaded and then hopefully the strange problems will go away.

1. Remove Conflicting Drivers
rmmod rt2500usb
rmmod rt2x00lib
rmmod rt2x00usb

2. Reinsert the device

3. Load rndis_wlan
modprobe rndis_wlan

You should now restart NetworkManager and things should be good to go. You might wanna check out the bug report I made for Fedora/RH.
Title: Re: *experimental* wireless usb support package
Post by: henno on August 06, 2009, 10:09:17 PM
Sorry, just one more article on my problem: (http://javamonks.com/support/linux/belkin_F5D7051.php)

Belkin F5D7051 on Linux

It is possible to get the Belkin F5D7051 "High-Speed Mode USB Adapter" working on Linux. I have been using it on various versions of Kubuntu (Hardy and Intrepid). The following instructions have been adapted from http://thehardsell.wordpress.com/

In order to use the wireless stick you need to use ndiswrapper - a tool that maps the Windows NDIS network drivers onto Linux. Ensure ndiswrapper is installed on your Linux box.

You also need the Windows drivers for the F5D7051. These are included on the original CD-ROM, or can be downloaded from the Belkin website as an .exe file. You can then extract the files using Ark or another archive tool. You should tell Ark to treat the file as an 'Archive Zip'.

The files you need are:

bcm43xx.cat
bcmrndis.inf
f5d7051.dll
rndismpk.sys
usb8023k.sys
As Linux is case sensitive, and the files will extract all in capital letters, you need to rename them to lower case. You can do this in Dolphin or in a terminal.

In the directory where you extracted the files now issue the following command in a terminal:

sudo ndiswrapper -i bcmrndis.inf
Now go to the ndiswrapper directory and check that everything is working.

cd /etc/ndiswrapper/bcmrndis
ls
I have found that the files do not transfer accross, so just move them accross by hand (using sudo in a terminal, or kdesudo to run Dolphin). The directory listing should be:

050D:7051.F.conf    bcm43xx.cat     f5d7051.dll     usb8023k.sys
1799:7051.F.conf    bcmrndis.inf    rndismpk.sys
Now ask ndiswrapper what drivers there are with a ndiswrapper -l command. The output should look like:

bcmrndis : driver installed
     device (080D:7051) present (alternative driver: rt2500usb)
Unfortunately the Linux driver for a Realtek chipset thinks it should operate this device (hence alternative driver). You therefore need to tell Linux not to load the RT2500 driver by editing the blacklist:

sudo kate /etc/modprobe.d/blacklist
and add the following line to the end:

blacklist rt2500usb
Reboot and your Belkin stick should now be working.
Title: Re: *experimental* wireless usb support package
Post by: korkut on August 09, 2009, 07:20:46 AM
Hello all,

I am new to the forums and read about every thing in here to get my Linksys WUSB54GC v2 ID 1737:0073 running for awhile but no sucess.
I could not find driver for it.

Can any tell me if is it supported if not compile a driver for it?

I'll be so happy If could use it on my WDTV.

Thank you for your comments/help in advance.

Korkut
Title: Re: *experimental* wireless usb support package
Post by: kaim on August 11, 2009, 11:34:10 PM
Hi,
can anyone tell me what would be the best adapter to buy (which means that it should be easy to install, working 100% with WPA2 and relatively cheap).

From what I read here I tend to buy a Zydas-based adapter like Zyxel G-202.
Is there a difference between http://www.amazon.de/Zyxel-G-202-802-11g-Wlan-Adapter/dp/B000HXDFT8/ref=wl_it_dp?ie=UTF8&coliid=IL8VG1ZCRLO9D&colid=1KUD90O2L83R7 (http://www.amazon.de/Zyxel-G-202-802-11g-Wlan-Adapter/dp/B000HXDFT8/ref=wl_it_dp?ie=UTF8&coliid=IL8VG1ZCRLO9D&colid=1KUD90O2L83R7) and http://www.amazon.de/Zyxel-G-202-802-11g-Wlan-Adapter/dp/B000HXDFT8/ref=wl_it_dp?ie=UTF8&coliid=IL8VG1ZCRLO9D&colid=1KUD90O2L83R7 (http://www.amazon.de/Zyxel-G-202-802-11g-Wlan-Adapter/dp/B000HXDFT8/ref=wl_it_dp?ie=UTF8&coliid=IL8VG1ZCRLO9D&colid=1KUD90O2L83R7)?

Thanks in advance!
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 17, 2009, 01:10:50 AM
I have now the ext3 boot-0.9.2 flashed and become a IP from my Router with WPA2 Encryption.

My WLAN Stick
Code: [Select]
Chipset - zd1211
VID - 0ace
PID - 1215

net.config:
Code: [Select]
HOST=wdtv
ifconfig eth0 up
sleep 5
wpa_supplicant -Bw -Dotus -ieth0 -c/boot/wpa_supplicant.conf
MTU=9000
DHCP=yes

this is my messages.txt, only an excerpt:

Code: [Select]
.....Jan  1 00:00:47 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:00:47 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:00:48 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:48 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:49 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:49 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:49 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:52 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:52 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:54 wdtv user.notice root: net.agent: Using pool.ntp.org to set system time
Jan  1 00:00:55 wdtv user.notice root: Device eth0 configged as 192.168.2.104/192.168.2.1/255.255.255.0
Jan  1 00:00:56 wdtv user.notice root: net.mounts: loading /boot/net.mounts
Jan  1 00:00:57 wdtv daemon.notice statd[1481]: Version 1.1.5 Starting
Jan  1 00:00:57 wdtv daemon.notice statd[1481]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:01 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:01 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:09 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:09 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:09 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:09 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:10 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:10 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:10 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:10 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800...

this is my Router Log:
Code: [Select]
17.08.09 11:00:10 WLAN-Station angemeldet. Rechnername: wdtv, IP-Adresse: 192.168.2.104, Mac-Adresse: 00:02:72:54:2C:A4, Geschwindigkeit 54 MBit/s.
17.08.09 11:00:00 WLAN-Station angemeldet. Rechnername: wdtv, IP-Adresse: 192.168.2.104, Mac-Adresse: 00:02:72:54:2C:A4, Geschwindigkeit 54 MBit/s.
17.08.09 10:59:48 WLAN-Station angemeldet. Rechnername: wdtv, IP-Adresse: 192.168.2.104, Mac-Adresse: 00:02:72:54:2C:A4, Geschwindigkeit 54 MBit/s.

   
I get about every 10.sek the newly assigned IP.

I hope you can send me at least help the problem.

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on August 18, 2009, 09:57:53 PM
Steve

Just try to use a static IP address. I get an IP from my router using DHCP but I never really checked my router logs so I do not know if this effect is present there as well ;D
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 19, 2009, 02:17:33 AM
Thank you for your efforts to help me. Will test it tonight.

/EDIT   
What does this: *** Block Non-EAPOL packet before key installed: 0800 to mean or is it wrong?

/EDIT
My Test with static IP!
a part of my messages.txt:
Code: [Select]
Jan  1 00:00:58 wdtv user.notice root: net.agent: Called for eth0
Jan  1 00:00:58 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:58 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:59 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:59 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:59 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:05 wdtv daemon.notice statd[1471]: Version 1.1.5 Starting
Jan  1 00:01:05 wdtv daemon.notice statd[1471]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:08 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.2.104 GW=192.168.2.1
Jan  1 00:01:09 wdtv user.notice root: Testing static IP assignment...
Jan  1 00:01:10 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:10 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:20 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0806
Jan  1 00:01:21 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:01:21 wdtv user.info kernel: NTFS volume version 3.1.
Jan  1 00:01:21 wdtv user.notice root: Now mounted:
Jan  1 00:01:21 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:21 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:21 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:21 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:21 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:21 wdtv user.notice root: /dev/sdb1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:21 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:01:21 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:21 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:01:21 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:21 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:21 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0806
Jan  1 00:01:21 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:21 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:21 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:21 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:01:21 wdtv user.notice root: /dev/sdb1 on /tmp/media/usb/USB2/8A0C-9003 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:21 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB1/400227D80227D1A8 type ntfs (ro,noatime,nodiratime,uid=0,gid=0,fmask=0177,dmask=077,nls=utf8,errors=continue,mft_zone_multiplier=1)
Jan  1 00:01:22 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:22 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:22 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0806
Jan  1 00:01:24 wdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:24 wdtv user.notice root: IP Assignment failed. Trying DHCP

Steve
Title: Re: *experimental* wireless usb support package
Post by: TON on August 19, 2009, 09:42:10 PM
Steve

Notice this "%100 packet loss" in your messages.txt. When using static ip assignment the firmware tries to check if the configuration you supply will work correctly so it tries to ping your router. So you need to assure the following:


So first of all add "sleep 5" after the wpa_supplicant call in your net.config to take care of the second item above and check if you can ping your router from some other computer.
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 20, 2009, 02:29:49 AM
1. Ping request to the router works

2. without change to my configuration, I had only 50% packet loss, but only sometimes

3. I have the sleep 5 Entry in net.config

4. Weird, I think the message *** Block Non-EAPOL packet before key installed: 0800

5. I think that something slowly with the driver not working correctly
suche
   
As you can see the top post (DHCP = yes)
Code: [Select]
Jan  1 00:00:52 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:52 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:54 wdtv user.notice root: net.agent: Using pool.ntp.org to set system time
Jan  1 00:00:55 wdtv user.notice root: Device eth0 configged as 192.168.2.104/192.168.2.1/255.255.255.0
Jan  1 00:00:56 wdtv user.notice root: net.mounts: loading /boot/net.mounts
Jan  1 00:00:57 wdtv daemon.notice statd[1481]: Version 1.1.5 Starting
Jan  1 00:00:57 wdtv daemon.notice statd[1481]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:01 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:01 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:09 wdtv user.debug kernel: *** Block Non-EAPol packet before key installed:0800
I get an IP from the router only once every 10 sec. new, the LED on the stick is always on.
It seems as if the stick crashes.

With WDlxTV I never get WPA2 connection until now only with ext3-boot.

I do not know anymore. I have 3 Linux systems at home, 1 PC in your car, write some software itself, but the problem I stand on the hose.
   
I post again tonight my net.config.

Steve
Title: Re: *experimental* wireless usb support package
Post by: tacitus on August 20, 2009, 01:01:53 PM
Steve, I don't know why, but my wireless with WDLXTV didn't work properly until I went from:

wpa_supplicant -Bw -Dotus -ieth0 -c/boot/wpa_supplicant.conf

to

wpa_supplicant -B w -D otus -i eth0 -c /boot/wpa_supplicant.conf

(i.e. add spaces between the parameters and their values.  It might be just the "-D otus" you need, but I didn't test all combinations.  In the end, even though I got everything to boot fine, I couldn't get rid of the hangs that would occur later.  I have found ext3-boot to be much more stable with the exact same configuration.
Title: Re: *experimental* wireless usb support package
Post by: kaim on August 20, 2009, 11:40:59 PM
Just wanted to report that Wireless Connection with WPA2 and WDLXTV 0.5.6.2 works for me.

Adapter: Zyxel ZYAIR G-202
Drivers: http://wdtvforum.com/main/index.php?topic=1379.0
net.config:
Code: [Select]
HOST=wdtv

insmod /boot/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 5

MTU=9000

DHCP=yes

SUPPRESS_OTHERS=yes
wpa_supplicant.conf:
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="SSID"
key_mgmt=WPA-PSK
psk="password"
}

Anyway, I am still searching for the best way to edit/put Files on my HDD attached to the WDTV over network.
Using the samba app, I can see the WDTV in network, but I can't write on the HDD (rights issue?), using FTP with pureFTP is very slow.
As far as I understood, NFS just works the other way around, allowing me to access Shares from another Computer on the WDTV, right?
Any ideas?
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 21, 2009, 04:40:00 AM
Hallo kaim

Ich weiß das du deutsch sprichst.
Ich hätte da noch ein paar Fragen bezüglich WLAN + WPA2.
Welchen Chipsatz hat dein Stick, und welche app.bin nutzt du alle?

Das mit deinen Rechten per FTP sollte sich doch leicht ändern lassen wenn du Telnet oder SSH Zugriff auf der Box hast.

Steve
Title: Re: *experimental* wireless usb support package
Post by: kaim on August 21, 2009, 08:55:03 AM
Hi,
ich denke mal, mit chipsatz meinst du vid und pid? Hier ein Auszug aus der messages.txt:

Code: [Select]
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: vendor_id = 0586
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: product_id = 3410
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: USB 2.0 Host
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: Release Ver = 4810
Jan  1 00:01:06 WDTV-f4996 user.notice kernel: EEPROM Ver = 4810

Ich habe den Stick von Amazon:
http://www.amazon.de/Zyxel-ZYAIR-802-11G-Wireless-Adapter/dp/B00129ADF0/ref=wl_it_dp_o?ie=UTF8&coliid=I2UI5TAA4C75P5&colid=1KUD90O2L83R7 (http://www.amazon.de/Zyxel-ZYAIR-802-11G-Wireless-Adapter/dp/B00129ADF0/ref=wl_it_dp_o?ie=UTF8&coliid=I2UI5TAA4C75P5&colid=1KUD90O2L83R7)

Das sind die apps, die ich momentan drauf habe:
LaurentG
event-osd
webserver
ThumbCache
log-saver
webserver-addons
appletrailerfs
pure-ftpd
wireless-mod-wdlxtv
eiri
samba


Das Rechte-Problem hat sich inzwischen erledigt: es gab im Netzwerk auf der WDTV den Ordner usb-ro (in dem das Rechte-Problem da war: ich konnte nicht schreiben, obwohl die Rechte auf rwxrwx waren) und den Ordner usb, auf den man, wie ich jetzt bemerkt habe, nur Zugriff bekommt mit user: WDTV-IP\root und leerem Passwort. Über diesen Ordner funktioniert das Schreiben. Allerdings momentan auch nur mit ca. 135 kb/s...da muss ich noch eine bessere Lösung finden.

Gruß
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 21, 2009, 09:22:44 AM
Ich habe ja jetzt die ext3-boot drauf, den mit der wireless-mod-wdlxtv und WDlxTV hatte es bei mir nie geklappt.
Habe jetzt schon alle Möglichkeiten durch. Wie ich ein paar post weiter oben geschrieben habe, bekomme ich von meinem Router ja eine IP zugewiesen nur bekomme ich sie alle 10 sek. neu.

Dein Eintrag von insmod /boot/zd1211b.ko kann bei WDlxTV nicht funktionieren, dann muss das /tmp/mnt/sda1/zd1211b.ko lauten

Steve
Title: Re: *experimental* wireless usb support package
Post by: kaim on August 21, 2009, 01:02:42 PM
Dein Eintrag von insmod /boot/zd1211b.ko kann bei WDlxTV nicht funktionieren, dann muss das /tmp/mnt/sda1/zd1211b.ko lauten
Warum nicht? Ich kenne mich nicht allzu gut mit Linux aus, aber genau so funktioniert es. Ich habe das einfach von hier: http://wdtvforum.com/main/index.php?topic=1379.0 (http://wdtvforum.com/main/index.php?topic=1379.0) übernommen und es funktioniert.

Oder kann es etwa sein, dass der Treiber dann gar nicht geladen wird (wenn der Pfad nur bei ext3-boot geht) und es trotzdem geht, dank wireless-mod-wdlxtv?

Ich werde nachher mal versuchen, die Zeile auszukommentieren.

Ich verwende momentan übrigens eine statische IP, damit ich nicht immer die IP anpassen muss, wenn ich vom Rechner auf die WDTV zugreifen will, aber ich habe nicht das Gefühl, dass statisch/dynamisch einen Unterschied macht.
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 22, 2009, 12:05:07 AM
Also das mit dem /boot Pfad kann bei WDlxTV ncht funktionieren da es diesen nicht gibt, du hast den Pfad ja auch hier
Code: [Select]
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf angepasst.

Ich verstehe auch nicht warum das bei mir nicht das bei mir nicht funktioniert, habe schon alle Möglichkeiten und Einstellungen mit ext3-boot und WDlxTV durch, es funktioniert ja auch wenn ich keine Verschlüsselung am Router eingestellt habe.

Werde heute mal wieder auf WDlxTV zurück und genau deine Einstellung testen, denn der Chipsatz deines WLAN Sticks ist der gleiche wie bei mir.

Steve
Title: Re: *experimental* wireless usb support package
Post by: kaim on August 22, 2009, 01:35:19 AM
Ich habe gerade nochmal 3 Tests gemacht, bei denen ich diese eine Zeile verändert habe:

Code: [Select]
#insmod /boot/zd1211b.ko-> no IP

Code: [Select]
/tmp/mnt/sda1/zd1211b.ko-> no IP

Code: [Select]
insmod /boot/zd1211b.ko-> funktioniert :)
Bei der Einstellung (und nur bei der) ist es auch so, dass ich die RSS-Feeds, die Uhr und das Wetter von webserver-addons erst sehe, wenn ich in standby gehe und dann wieder einschalte.

Ich habe keine Erlärung dafür, vielleicht gibt es auch noch andere Einflüsse (ich habe gleichzeitig noch lilibabes osd mod ausprobiert), aber du solltest die Einstellung wenigstens mal ausprobieren.
Title: Re: *experimental* wireless usb support package
Post by: Steve on August 22, 2009, 02:02:51 AM
Habe es geschafft.

I have runing.

WDlxTV 0.6.2
wireless-mod-wdlxtv.app.bin

net.config
Code: [Select]
HOST=wdtv

insmod /tmp/mnt/sda1/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 5

MTU=9000

DHCP=yes

SUPPRESS_OTHERS=yes

wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Ganja-WLAN"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="*****"
}


Steve
Title: Re: *experimental* wireless usb support package
Post by: tacitus on August 26, 2009, 08:55:47 AM
Hi, I've been successfully running with ext3-boot for the past couple of weeks with a wireless setup, using a TL-WN322G wireless-G USB dongle and TL-WR541G wireless hub.  When I was using an NFS share with:

udp,rsize=32768,wsize=32768

I could even get some short 720p streams to play quite nicely, but then I kept running into a problem.  If the stream started stuttering in any way, I could no longer stream anything greater than about 250kbytes/sec after that, even though my wireless link is easily capable of over 1500kbytes/sec before the problems start.  Stopping the stream and starting another one (even if it's just SD) doesn't solve the problem.

I finally figured out that all I had to do to fix the problem is reboot my TL-WR541G wireless hub.  That clears the problem for a while at least, but it always comes back eventually, usually after playing a TV show or two.  I've been playing with the NFS share parameters and discovered last night that changing from UDP to TCP also seems to solve the problem, though at the cost of noticeably lower bandwidth.  720p files no longer play, but the hub's performance always recovers immediately after a stuttering file stopped or rewound.  The hub is no longer "locked in" to a much slower rate.  

Also, FTPing a file over the same link now seems to cause the same problem -- I have to reset the hub almost immediately.

Given what I know so far, it does seem that the wireless hub is at fault here -- it doesn't handle high-bandwidth UDP streams at all well (and even at lower bandwidths it fails eventually).  The question is, does anyone have any idea what might be causing the hub's performance to degrade so markedly?  Do I just have a bad hub, or are there more configuration options I can use to prevent my WDTV box from giving conniptions every few minutes?  Does anyone have the same type of problem?

*** Update ***

Well, I'm not sure what I did (if anything), but my router is now behaving itself much better now.  Still not getting the throughput I was at one point---not enough to play uncompressed DVD rips over the network without stuttering but at least I don't have to keep resetting the hub every time it happens.
Title: Re: *experimental* wireless usb support package
Post by: deki20 on September 02, 2009, 08:53:58 PM
Hi,
first, regards to all member of this forum...
I bought few days ago, WDTV and yestarday D-link DWL-G122 USB Wifi adapeter /RT73 chip/....
I have WDlxTV 0.6.2 firmware...
I was try couple variants for drivers, buy result is  :'(
Is not nesessery encription for me...
Pls, what files I must have?

wireless-mod-wdlxtv.app.bin  I think, or somethink else?
net.config?
another files?

Thanks for all!!!
Sorry for my english...

Best regards...
Title: Re: *experimental* wireless usb support package
Post by: cobe on September 03, 2009, 09:47:55 AM
Hello everybody,

I have a DWL-G122 h/w:C1(vid 07d1 pid 3c03) D-Link wireless stick.
I have upgrade with ext3-boot-0.8.7.2.

host=wdtv
MTU=1452
insmod /boot/zd1211.ko
blacklist zd1211b
DHCP=no
IP=10.10.10.15
GW=10.10.10.1
NM=255.255.255.0
DNS1=86.104.123.150
DNS2=86.104.123.140
ifconfig $MDEV up
iwconfig $MDEV essid linksys s:mypassword

net mounts:
xmount 10.10.10.2:/torrents torrents nfs

after upgrade, my root looks like this:

.wd_tv
www
/changelog
/messages.0
/messages.txt
/net.config
/net.mounts
/root.bin
/wdtv.bin
/wdtv.ver
/zd1211.ko
/zd1211b.ko

I have a Linksys WRT150N router with WPA-Personal, Encryption AES, with mac milter on and D-link's mac added in the permitted list.

My d-link receives no ip...should i add wireless-mod.app.bin? which version?

thank you a lot for helping me!

My messages.txt follow...


Title: Re: *experimental* wireless usb support package
Post by: cobe on September 03, 2009, 09:49:46 AM
Jan  1 00:00:48 WDTV-73761 syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:48 WDTV-73761 user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:48 WDTV-73761 user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:48 WDTV-73761 user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:48 WDTV-73761 user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:48 WDTV-73761 user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Determined physical RAM map:
Jan  1 00:00:48 WDTV-73761 user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:48 WDTV-73761 user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:48 WDTV-73761 user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:48 WDTV-73761 user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:48 WDTV-73761 user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:48 WDTV-73761 user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Built 1 zonelists
Jan  1 00:00:48 WDTV-73761 user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:48 WDTV-73761 user.notice root: Displaying detected USB devices...
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:48 WDTV-73761 user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:48 WDTV-73761 user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:48 WDTV-73761 user.debug kernel: Calibrating delay loop... 292.86 BogoMIPS (lpj=146432)
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:48 WDTV-73761 user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:48 WDTV-73761 user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:48 WDTV-73761 user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:48 WDTV-73761 user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:48 WDTV-73761 user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:48 WDTV-73761 user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:48 WDTV-73761 user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:49 WDTV-73761 user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:49 WDTV-73761 user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:49 WDTV-73761 user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:49 WDTV-73761 user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:49 WDTV-73761 user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:49 WDTV-73761 user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:49 WDTV-73761 user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:49 WDTV-73761 user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:49 WDTV-73761 user.info kernel: Initializing Cryptographic API
Jan  1 00:00:49 WDTV-73761 user.info kernel: io scheduler noop registered
Jan  1 00:00:49 WDTV-73761 user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:49 WDTV-73761 user.info kernel: io scheduler deadline registered
Jan  1 00:00:49 WDTV-73761 user.info kernel: io scheduler cfq registered
Jan  1 00:00:49 WDTV-73761 user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:49 WDTV-73761 user.notice root:  [07d1:3c03] 1-1( 2.00,480m) 802.11 bg WLAN
Jan  1 00:00:50 WDTV-73761 user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:50 WDTV-73761 user.notice root:  [0951:1623] 1-2( 2.00,480m) DataTraveler 120/5B911000000A
Jan  1 00:00:50 WDTV-73761 user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:50 WDTV-73761 user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:50 WDTV-73761 user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:50 WDTV-73761 user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:50 WDTV-73761 user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:50 WDTV-73761 user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:50 WDTV-73761 user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:50 WDTV-73761 user.notice kernel: number of CFI chips: 1
Jan  1 00:00:50 WDTV-73761 user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:50 WDTV-73761 user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:50 WDTV-73761 user.notice kernel: Using physmap partition definition
Jan  1 00:00:50 WDTV-73761 user.notice kernel: Adding partition #1-#5
Jan  1 00:00:50 WDTV-73761 user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:50 WDTV-73761 user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:50 WDTV-73761 user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:50 WDTV-73761 user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:50 WDTV-73761 user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:50 WDTV-73761 user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:50 WDTV-73761 user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:50 WDTV-73761 user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:50 WDTV-73761 user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:50 WDTV-73761 user.warn kernel: TangoX USB initializing...
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:50 WDTV-73761 user.info kernel: hub 1-0:1.0: USB hub found
Jan  1 00:00:50 WDTV-73761 user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:50 WDTV-73761 user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:50 WDTV-73761 user.warn kernel: Initializing Tango
Jan  1 00:00:50 WDTV-73761 user.info kernel: X USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:50 WDTV-73761 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:50 WDTV-73761 user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:50 WDTV-73761 user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:50 WDTV-73761 user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:50 WDTV-73761 user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:50 WDTV-73761 user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:50 WDTV-73761 user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:50 WDTV-73761 user.debug kernel: usb-storage: device found at 3
Jan  1 00:00:50 WDTV-73761 user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:50 WDTV-73761 user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:50 WDTV-73761 user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:50 WDTV-73761 user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:51 WDTV-73761 user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:51 WDTV-73761 user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:51 WDTV-73761 user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:51 WDTV-73761 user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:51 WDTV-73761 user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:51 WDTV-73761 user.info kernel: TCP reno registered
Jan  1 00:00:51 WDTV-73761 user.info kernel: TCP bic registered
Jan  1 00:00:52 WDTV-73761 user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:52 WDTV-73761 user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:52 WDTV-73761 user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:52 WDTV-73761 user.notice kernel:   Vendor: Kingston  Model: DataTraveler 120  Rev: PMAP
Jan  1 00:00:52 WDTV-73761 user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:00:52 WDTV-73761 user.notice kernel: SCSI device sda: 7843840 512-byte hdwr sectors (4016 MB)
Jan  1 00:00:52 WDTV-73761 user.notice kernel: sda: Write Protect is off
Jan  1 00:00:52 WDTV-73761 user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:52 WDTV-73761 user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:52 WDTV-73761 user.notice kernel: SCSI device sda: 7843840 512-byte hdwr sectors (4016 MB)
Jan  1 00:00:52 WDTV-73761 user.notice kernel: sda: Write Protect is off
Jan  1 00:00:52 WDTV-73761 user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:52 WDTV-73761 user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:52 WDTV-73761 daemon.info utelnetd[541]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Title: Re: *experimental* wireless usb support package
Post by: cobe on September 03, 2009, 09:51:36 AM
Jan  1 00:00:52 WDTV-73761 user.info kernel:  sda: sda1
Jan  1 00:00:52 WDTV-73761 user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:52 WDTV-73761 user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:52 WDTV-73761 user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:52 WDTV-73761 user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:00:52 WDTV-73761 user.info kernel: EXT3 FS on loop1, internal journal
Jan  1 00:00:52 WDTV-73761 user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:00:52 WDTV-73761 user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:00:52 WDTV-73761 user.warn kernel: zd1211: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:52 WDTV-73761 user.warn kernel: zd1211: Unknown symbol wireless_send_event
Jan  1 00:00:52 WDTV-73761 user.info kernel: usb 1-2: reset high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:52 WDTV-73761 user.notice root: INIT: mounting app binaries...
Jan  1 00:00:52 WDTV-73761 user.notice root: Path set to /boot/bin:/opt/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:53 WDTV-73761 user.notice root: INIT: Starting /etc/init.d/rcS
Jan  1 00:00:54 WDTV-73761 user.notice root: vfat: Waiting for 7CF8-31A6 to mount
Jan  1 00:00:54 WDTV-73761 user.notice root: Polling detected drives...
Jan  1 00:00:54 WDTV-73761 user.notice root: Waiting for /dev/sda1 to come online (UUID=7CF8-31A6)...
Jan  1 00:00:56 WDTV-73761 authpriv.info dropbear[683]: Running in background
Jan  1 00:01:01 WDTV-73761 user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:01 WDTV-73761 user.info kernel: Loading wireless extentions module...
Jan  1 00:01:01 WDTV-73761 user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:03 WDTV-73761 user.warn kernel:
Jan  1 00:01:03 WDTV-73761 user.warn kernel:  _____     ____    _    ____
Jan  1 00:01:03 WDTV-73761 user.warn kernel: |__  /   _|  _ \  / \  / ___|
Jan  1 00:01:03 WDTV-73761 user.warn kernel:   / / | | | | | |/ _ \ \___ \
Jan  1 00:01:03 WDTV-73761 user.warn kernel:  / /| |_| | |_| / ___ \ ___) |
Jan  1 00:01:03 WDTV-73761 user.warn kernel: /____\__, |____/_/   \_\____/
Jan  1 00:01:03 WDTV-73761 user.warn kernel:      |___/
Jan  1 00:01:03 WDTV-73761 user.notice kernel: zd1211 - version 2.22.0.0-development
Jan  1 00:01:03 WDTV-73761 user.info kernel: usbcore: registered new driver zd1211
Jan  1 00:01:04 WDTV-73761 user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 WDTV-73761 user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 WDTV-73761 user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:05 WDTV-73761 user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:05 WDTV-73761 user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:05 WDTV-73761 user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:05 WDTV-73761 user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:05 WDTV-73761 user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:05 WDTV-73761 user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:05 WDTV-73761 user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:05 WDTV-73761 user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:06 WDTV-73761 user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:06 WDTV-73761 user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:06 WDTV-73761 user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:06 WDTV-73761 user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:06 WDTV-73761 user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:06 WDTV-73761 user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:06 WDTV-73761 user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:07 WDTV-73761 user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:07 WDTV-73761 user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:07 WDTV-73761 user.warn kernel: Starting OpenWDTV IR driver
Jan  1 00:01:07 WDTV-73761 user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:07 WDTV-73761 user.debug kernel: ir: Enable RC5 decoder (0x80001e80)
Jan  1 00:01:07 WDTV-73761 user.warn kernel: OpenWDTV.ir Opened /dev/ir0(96a99f70) real IR device
Jan  1 00:01:12 WDTV-73761 daemon.notice statd[1176]: Version 1.1.5 Starting
Jan  1 00:01:12 WDTV-73761 daemon.notice statd[1176]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:14 WDTV-73761 user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:01:18 WDTV-73761 user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:01:18 WDTV-73761 user.warn kernel: em8xxx0 [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:01:18 WDTV-73761 user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:01:18 WDTV-73761 user.warn kernel: mumk_register_tasklet: (0) tasklet c50d6000 status @c932ba54
Jan  1 00:01:18 WDTV-73761 user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:01:21 WDTV-73761 user.warn kernel: OpenWDTV.ir opened client 0
Jan  1 00:01:21 WDTV-73761 user.warn kernel: OpenWDTV.ir calling trylock client_id 0
Jan  1 00:01:21 WDTV-73761 user.warn kernel: OpenWDTV.ir trylock aquired read lock 1 client_id 0
Jan  1 00:01:32 WDTV-73761 user.notice root: xmounter: entering stage2
Jan  1 00:01:32 WDTV-73761 user.notice root: Now mounted:
Jan  1 00:01:32 WDTV-73761 user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:32 WDTV-73761 user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:32 WDTV-73761 user.notice root: /dev/loop1 on / type ext3 (rw,sync,noatime,nodiratime,data=ordered)
Jan  1 00:01:32 WDTV-73761 user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:32 WDTV-73761 user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:32 WDTV-73761 user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:33 WDTV-73761 user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:33 WDTV-73761 user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:33 WDTV-73761 user.notice root: /dev/loop1 on /lib/modules/old-or-new type ext3 (rw,sync,noatime,nodiratime,data=ordered)
Jan  1 00:01:33 WDTV-73761 user.notice root: fuse on /osd-php type fuse (rw,nosuid,nodev,user_id=0,group_id=0)
Jan  1 00:01:33 WDTV-73761 user.notice root: /dev/sda1 on /tmp/media/usb/USB2/7CF8-31A6 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:36 WDTV-73761 user.notice root: INIT: Finished
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir readed 4 bytes
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir readed 1 commands
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir readed command: 3977410948
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir writen 4 bytes to consumer(0) 4 out of 4
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir calling trylock client_id 0
Jan  1 00:01:58 WDTV-73761 user.warn kernel: OpenWDTV.ir trylock aquired read lock 1 client_id 0
Jan  1 00:02:01 WDTV-73761 user.info kernel: usb 1-1: USB disconnect, address 2


the end
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on September 03, 2009, 01:01:29 PM
Answered you via your e-mail. Basically, you were using Zydas drivers with a RT-73 chip based dongle.
This thread contains all the needed steps and the solution: http://wdtvforum.com/main/index.php?topic=1029.0

And one thing I don't understand. Why some of you can't test the wireless out using only WEP instead of WPA TKIP AES and all that. It makes all the problems easier to troubleshoot. Later, supplicant files and encryption can be added easily.

People, please... I know WEP is not secure, but it's not like there's a Linux totin' haxxor bloke across the street just waiting to hack your WEP, come on... :D
Title: Re: *experimental* wireless usb support package
Post by: TON on September 03, 2009, 09:41:17 PM
Frosty_CRO

I do not think it is always a matter of security. I have several computers at home connected via wireless with WPA. It was too much effort to change everything to WPA just to test WDTV connection. I managed to make it work with WPA after changing the dongle to Zydas-based one. Your advices helped too BTW.
Title: Re: *experimental* wireless usb support package
Post by: cobe on September 04, 2009, 08:11:22 AM
Thanks for all your help Frosty.

I managed to make it work, meaning that now the stick is recognized (dhcp or no), is scanning my NFS share, made following http://www.avsforum.com/avs-vb/showpost.php?p=16057281&postcount=1028 (http://www.avsforum.com/avs-vb/showpost.php?p=16057281&postcount=1028) tutorial. All the iso's and mkv are displayed.

The problem becomes when i try to play anything. Is not working, not even a avi mpg2 file :(. It is blocking after the first 10 seconds

I have ext3-boot-0.8.7.2, wireless-mod-rt.app.bin-1.31, fat(or fat32) usb stick drive.
The root folder looks like this:
/.wd_tv
/torrents
/www
Changelog
messages.0
messages.txt
net.config
net.mounts
root.bin
rt73sta.dat
wdtv.bin
wdtv.ver
wireless-mod-rt.app.bin

The configuration files are looking like this:
Code: [Select]
host=wdtv
MTU=1492
sleep=5
DHCP=no
sleep=5

IP=10.10.10.10
GW=10.10.10.1
NM=255.255.255.0
DNS1=86.104.123.150
DNS2=86.104.123.140
sleep=5

NTP=pool.ntp.org
SUPPRESS_OTHERS="yes"


WLAN_CFG=rt73sta.dat
WLAN_LOAD=rt73.ko
WLAN_UP=yes
WLAN_SLEEP=1

rt73sta.dat:

Code: [Select]
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=linksys
NetworkType=Infra
Channel=6
AuthMode=WPA2PSK
EncrypType=TKIP
WPAPSK=fortzarapixxxxxxxxx
TxBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy=0;0;0;0
BGProtection=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
AdhocOfdm=0
FastRoaming=0
RoamThreshold=70

xmount 10.10.10.2:/torrents torrents nfs in net.mounts

my router has WPA2PERSONAL- TKIP OR AES

i have noticed that at the beginning of loading the movie, the link  led is shutting donw for 4-5 sec and then re-lighting...

sorry if toked to much time, but now it WORK BEAUTIFULLY. I have not seen a movie till end,
but it works to ffwd 2 or 4 smoothly enough on a 720p DTS file.
if you were wondering, i have only switched places for stick and wi-fi. The wi-fi is now plugged in back, next to the power, hdmi, etc...

thanks again for the great work doing here.





Title: Re: *experimental* wireless usb support package
Post by: barrmy on September 08, 2009, 07:14:53 PM
ok...i feel like I must be doing something dumb, because i feel like i've tried it all...i'm still getting no ip
thanks in advance for any help


My network is typically wpa/wpa2-aes, but i tried it with WEP and no p/w (you'll see the commented out code) as well and static ip - and still got 'no ip'.  No mac filtering on router, and ssid is broadcast.  I also tried it on my second router which is a ddwrt wpa2-tkip/aes, and i didn't try to clear out those settings.  The zyxel does light up blue on boot, but not flashing.

posts I tried to follow:
http://wdtvforum.com/main/index.php?topic=1379.msg10477#msg10477
http://wdtvforum.com/main/index.php?topic=59.msg14211#msg14211

net.config
Code: [Select]
HOST=wdtv

insmod /boot/zd1211.ko
#blacklist zd1211b
sleep 10
ifconfig $MDEV up
#iwconfig $MDEV essid pixel_vz key 21xxxxxx89
wpa_supplicant -B w -D otus -i $MDEV -c /boot/wpa_supplicant.conf
sleep 5

MTU=9000

DHCP=yes

SUPPRESS_OTHERS=yes

wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="pixel_vz"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="mycode"
}
Title: Re: *experimental* wireless usb support package
Post by: Frosty_CRO on September 09, 2009, 02:49:03 PM
You got a bit "happy" with the comment # xD!

Try this for your net.config ( Drive is plugged in the USB 1 port? ):

HOST=wdtv
MTU=9000
insmod /tmp/mnt/sda1/zd1211.ko
blacklist zd1211b
SUPPRESS_OTHERS=yes
sleep 5
ifconfig $MDEV up
sleep 5
wpa_supplicant -B w -D otus -i $MDEV -c /boot/wpa_supplicant.conf
DHCP=yes
Title: Re: *experimental* wireless usb support package
Post by: KeithGP on September 11, 2009, 07:24:07 AM
Anyone familiar with the Rosewill rnx-n100?  It has the Ralink 2770 chipset.  I could have sworn it had the Ralink 2870 chipset that is supported before I purchased it but it's OK.  I have it now.  Would this chipset work with?

Thanks!
Title: Re: *experimental* wireless usb support package
Post by: Simracer on September 14, 2009, 02:15:09 AM
Hi to all. I am happy owner of WD HD TV for a week, but already tired to plug-unplug and walk to computer/netbook with my 1,5 TB Seagate USB HDD. I don't want to stream media from my PCs, i just want to upload/delete files to HDD, attached to WDTV.
I have absolutely useless Compex WLU108AG wireless dongle with Atheros AR5523-ES Chip: (http://simracer.users.photofile.ru/photo/simracer/3566604/large/86418410.jpg)

Is it possible to connect WDTV via this adapter to my home wi-fi network?

My wireless router with free LAN ports is placed near the WDTV - may be it would be better to set USB-LAN adapter and to plug it to wireless router by cord (just to save wireless bandwidth?)

Title: Re: *experimental* wireless usb support package
Post by: dougzibart on September 14, 2009, 07:18:31 AM
Hello everybody. I was wondering what kind of speeds everyone here was getting using wireless streaming. I have Zyxel G202 wi-fi adapter with Asus WL-500GP router and my WD TV starts choking playing 720p files with bitrates ~ 8 Mbps. I'm running hanewin NFS server, my router and WD TV are quite close to each other (around 30 feet apart without many obstacles). I was under the impression I'd be able to stream at least 720p video, so is there something wrong with my setup or is this as good as it can get?
Title: Re: *experimental* wireless usb support package
Post by: Dukman on September 16, 2009, 05:39:00 PM
Hello everybody. I was wondering what kind of speeds everyone here was getting using wireless streaming. I have Zyxel G202 wi-fi adapter with Asus WL-500GP router and my WD TV starts choking playing 720p files with bitrates ~ 8 Mbps. I'm running hanewin NFS server, my router and WD TV are quite close to each other (around 30 feet apart without many obstacles). I was under the impression I'd be able to stream at least 720p video, so is there something wrong with my setup or is this as good as it can get?
If you got this far you're almost there. I have mine set up with a Linksys WUSB600N adapter, a Belkin N Router and a Dlink DNS-323 NAS running NFS. I had the same problem. I found some info on NFS optimization here.

http://www.higs.net/85256C89006A03D2/web/PageLinuxNFSPerformance

Once I started changing the rsize= & wsize values in the xmount line I was able to get 720p material running smooth and almost all 1080p but I was still getting freezing on some 1080p, the largest sized files are 15gb.

However once I saw how great it was to have 1080p streaming from an NAS, I gave up on the thing and built a home theatre PC. I still believe the box is a great value when used as advertised.

Hope this helps.
Title: Re: *experimental* wireless usb support package
Post by: tech324 on October 01, 2009, 01:50:46 AM
I am running the WDTV with the WDLXTV firmware version 0.5.6.1.  I am trying to get wireless setup.  I have a Buffalo WLI-UC-GN wireless N adapter.  I read that the adapter is using the RaLink RT2870 chipset.  I have tried WDLXTV and ext3-boot.  I have tried using wireless-mod-wdlxtv.app.bin, Zorander's wireless-mod.app.bin, as well as the pack from wireless-mod-0.3-sebmod.zip.  I think my issue might be that the WDTV is not detecting my adapter.  Any help is greatly appreciated. If I missed anything let me know and I will post it.  This is my message.txt file:

**** You will notice that it sees a WLAN adapter but doesn't provide any information:

Jan  1 00:00:20 WDTV-249b5 user.notice root:  [0411:015d] 1-2( 2.00,480m) 802.11 n WLAN/1.0


message.txt:

Jan  1 00:00:16 WDTV-249b5 syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:16 WDTV-249b5 user.notice root: usb.agent hotplugged /dev/sda1
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:16 WDTV-249b5 user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:16 WDTV-249b5 user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Determined physical RAM map:
Jan  1 00:00:16 WDTV-249b5 user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:16 WDTV-249b5 user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:16 WDTV-249b5 user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:16 WDTV-249b5 user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:16 WDTV-249b5 user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:16 WDTV-249b5 user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Built 1 zonelists
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:16 WDTV-249b5 user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:16 WDTV-249b5 user.debug kernel: Calibrating delay loop... 292.86 BogoMIPS (lpj=146432)
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:16 WDTV-249b5 user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:16 WDTV-249b5 user.notice root: 1.02.10.WDLXTV-0.5.6.1
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:16 WDTV-249b5 user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:16 WDTV-249b5 user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:16 WDTV-249b5 user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:16 WDTV-249b5 user.info kernel: Initializing Cryptographic API
Jan  1 00:00:16 WDTV-249b5 user.info kernel: io scheduler noop registered
Jan  1 00:00:16 WDTV-249b5 user.notice root: Displaying detected USB devices...
Jan  1 00:00:16 WDTV-249b5 user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:16 WDTV-249b5 user.info kernel: io scheduler deadline registered
Jan  1 00:00:16 WDTV-249b5 user.info kernel: io scheduler cfq registered
Jan  1 00:00:16 WDTV-249b5 user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:16 WDTV-249b5 user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:16 WDTV-249b5 user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:16 WDTV-249b5 user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:16 WDTV-249b5 user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:16 WDTV-249b5 user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:16 WDTV-249b5 user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:16 WDTV-249b5 user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: number of CFI chips: 1
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: Using physmap partition definition
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: Adding partition #1-#5
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:16 WDTV-249b5 user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:16 WDTV-249b5 user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: TangoX USB initializing...
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:16 WDTV-249b5 user.info kernel: hub 1-0:1.0: USB hub found
Jan  1 00:00:16 WDTV-249b5 user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: Initializing Tango
Jan  1 00:00:16 WDTV-249b5 user.info kernel: X USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:16 WDTV-249b5 user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:16 WDTV-249b5 user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:16 WDTV-249b5 user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:16 WDTV-249b5 user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:16 WDTV-249b5 user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:16 WDTV-249b5 user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:16 WDTV-249b5 user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:16 WDTV-249b5 user.debug kernel: usb-storage: device found at 2
Jan  1 00:00:16 WDTV-249b5 user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:16 WDTV-249b5 user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:16 WDTV-249b5 user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:16 WDTV-249b5 user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:16 WDTV-249b5 user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:16 WDTV-249b5 user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:16 WDTV-249b5 user.info kernel: TCP reno registered
Jan  1 00:00:16 WDTV-249b5 user.info kernel: TCP bic registered
Jan  1 00:00:16 WDTV-249b5 user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:16 WDTV-249b5 user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:16 WDTV-249b5 user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:17 WDTV-249b5 user.notice kernel:   Vendor: TDK LoR   Model: Trans-It Drive    Rev: PMAP
Jan  1 00:00:17 WDTV-249b5 user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:00:17 WDTV-249b5 user.notice kernel: SCSI device sda: 15843328 512-byte hdwr sectors (8112 MB)
Jan  1 00:00:17 WDTV-249b5 user.notice root: /dev/sda1: LABEL="FLASHDRIVE" UUID="D66B-1C2A" TYPE="vfat"
Jan  1 00:00:17 WDTV-249b5 user.notice root: /dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
Jan  1 00:00:17 WDTV-249b5 user.notice root: /dev/mtdblock3: LABEL="Compressed" TYPE="cramfs"
Jan  1 00:00:17 WDTV-249b5 user.notice root: crazymount: mounting app binaries...
Jan  1 00:00:17 WDTV-249b5 user.notice root: partition with label (FLASHDRIVE) already mounted!
Jan  1 00:00:17 WDTV-249b5 user.notice root: DEVICE /dev/sda1 CONNECTED
Jan  1 00:00:18 WDTV-249b5 user.notice root: log-saver app found
Jan  1 00:00:18 WDTV-249b5 user.notice root: Mounting log-saver.app.bin at /apps/log-saver
Jan  1 00:00:18 WDTV-249b5 user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:18 WDTV-249b5 user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:18 WDTV-249b5 user.notice kernel: sda: Write Protect is off
Jan  1 00:00:18 WDTV-249b5 user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:18 WDTV-249b5 user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:18 WDTV-249b5 user.notice kernel: SCSI device sda: 15843328 512-byte hdwr sectors (8112 MB)
Jan  1 00:00:19 WDTV-249b5 user.notice kernel: sda: Write Protect is off
Jan  1 00:00:19 WDTV-249b5 user.debug kernel: sda: Mode Sense: 23 00 00 00
Jan  1 00:00:19 WDTV-249b5 user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:19 WDTV-249b5 user.info kernel:  sda: sda1
Jan  1 00:00:19 WDTV-249b5 user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:19 WDTV-249b5 user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:19 WDTV-249b5 user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_10/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_10/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_10/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_10/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: loop: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop: loaded (max 24 devices)
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=68, limit=8
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:19 WDTV-249b5 user.notice root:  [1d0d:0213] 1-1( 2.00,480m) Trans-It Drive/078B0B15189E
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=1252, limit=8
Jan  1 00:00:19 WDTV-249b5 user.info kernel: attempt to access beyond end of device
Jan  1 00:00:19 WDTV-249b5 user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: UDF-fs: No partition found (1)
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:19 WDTV-249b5 user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:19 WDTV-249b5 user.notice root: adjusting LIBPATH
Jan  1 00:00:20 WDTV-249b5 user.notice root:  [0411:015d] 1-2( 2.00,480m) 802.11 n WLAN/1.0
Jan  1 00:00:22 WDTV-249b5 user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:22 WDTV-249b5 user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:23 WDTV-249b5 user.notice root: adjusting PATH
Jan  1 00:00:23 WDTV-249b5 user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:28 WDTV-249b5 user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:28 WDTV-249b5 user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:28 WDTV-249b5 user.info kernel: usbcore: registered new driver asix
Jan  1 00:00:29 WDTV-249b5 user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:00:29 WDTV-249b5 user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:00:29 WDTV-249b5 user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:00:29 WDTV-249b5 user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:00:29 WDTV-249b5 user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:00:29 WDTV-249b5 user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:00:29 WDTV-249b5 user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:00:29 WDTV-249b5 user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:00:29 WDTV-249b5 user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:30 WDTV-249b5 user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:00:30 WDTV-249b5 user.info kernel: usbcore: registered new driver catc
Jan  1 00:00:30 WDTV-249b5 user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:00:30 WDTV-249b5 user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:00:31 WDTV-249b5 user.info kernel: usbcore: registered new driver net1080
Jan  1 00:00:31 WDTV-249b5 user.info kernel: usbcore: registered new driver plusb
Jan  1 00:00:31 WDTV-249b5 user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:00:31 WDTV-249b5 user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:00:33 WDTV-249b5 user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:33 WDTV-249b5 user.info kernel: Loading wireless extentions module...
Title: Re: *experimental* wireless usb support package
Post by: daskino on October 01, 2009, 04:45:47 AM
Does the WDTV work with the USB antenna you get when you buy the XtreameR?

I have an WDTv and my borthe ris not using his antenna, can I hook up with the WDTV instead?

Found the spec here

Chipset
·  Ralink RT3070 Single Chip

Standards
·  IEEE 802.11n (draft 2.0), IEEE 802.11g, IEEE 802.11b, Cisco CCX support, CSMA/CA with ACK

Wireless Signal Rates with Automatic Fallback
·  11n (20MHZ): MCS0-7 (up to 72Mbps)
·  11n (40MHZ) : MCS0-7 (up to 150Mbps)
Title: Re: *experimental* wireless usb support package
Post by: Phhh on October 01, 2009, 07:43:18 AM
Does the WDTV work with the USB antenna you get when you buy the XtreameR?

I have an WDTv and my borthe ris not using his antenna, can I hook up with the WDTV instead?

Found the spec here

Chipset
·  Ralink RT3070 Single Chip

Standards
·  IEEE 802.11n (draft 2.0), IEEE 802.11g, IEEE 802.11b, Cisco CCX support, CSMA/CA with ACK

Wireless Signal Rates with Automatic Fallback
·  11n (20MHZ): MCS0-7 (up to 72Mbps)
·  11n (40MHZ) : MCS0-7 (up to 150Mbps)


It should work fine, I have 2 USB adapters base on Ralink chipset RT3070 & RT2870 one similar to your's but different brand, Win-Star

h**p://www.win-star.com/eshop/goods.php?id=65
h**p://www.win-star.com/eshop/goods.php?id=63

Both of them stream 1080P fine.



Title: Re: *experimental* wireless usb support package
Post by: NorthernComfort on October 04, 2009, 04:38:14 PM
I bought a TrendNet TEW-644UB, apparently it is a RaLink chipset 2770.  I am asking for assistance.  I have some PC Linux experience.  I have installed b-rad.cc latest firmware, and tried Zorander wireless bin (even tried another wireless mod ap rt bin).  My wireless device begins to flicker a lot (thus is powered) after the OS boots, but boot up screen says "IP: No IP", thus, it seems the correct driver is not loaded.  I used the "dump bin" and see "Jan  1 00:00:16 WDTV-8b9be user.notice root:  [148f:2770] 1-1( 2.00,480m) 802.11 n WLAN/1.0", but no connection (DHCP or fixed), ping does not work, etc...  Is there a driver out there for it?  I believe PC Linux has one, how do I go about using the PC-Linux driver onto WDTV? (I have never done such things before).  My other choice is to return the device and keep looking for a supported device.  Thanks.  P.S.  This is an "N" wireless.  Running wired is possible, but I would have to cut holes in several walls, etc..., so not preferred.  Cheers.
Title: Re: *experimental* wireless usb support package
Post by: tech324 on October 04, 2009, 05:32:38 PM
NorternComfort,
I think I am in the same boat as you. I also get no ip with the wireless device plugged in (but the device is lit up). I have a Buffalo Wireless N device and I believe it has the RT2870 chipset.  When I pull the logs it looks like it sees the device:

Jan  1 00:00:20 WDTV-249b5 user.notice root:  [0411:015d] 1-2( 2.00,480m) 802.11 n WLAN/1.0

I would really like to get this wireless device to work (if possible) because I can't take it back.  I have tried both wdlxtv and Zorander's wireless driver packs with no success.

Title: Re: *experimental* wireless usb support package
Post by: hacksrus on October 05, 2009, 07:58:29 AM
I also would like some help, if that is possible :) Up to today, I was happily using ext3-boot, with event-osd. The network capabilities are not needed everyday, but I had to use them to configure event-osd properly... Homever, since ext3-boot development stopped, while wdlxtv gets every so often new updates (including USB hubs support, which becomes important for me), I moved onto it. Install of WDlxTV went without problems, on root of my mass storage (which was used earlier with ext3-boot) I have put also the wireless-mod-wdlxtv.app.bin (v0.2), and net.config (containing default configuration, plus WEP lines)

Code: [Select]
#
# Network configuration file

#You can override the hostname here:
HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:
DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)
#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional:  

#specify time server host
#NTP=pool.ntp.org

#specify timezone (example=pacific North America)
#TZ=PST8PDT

#do not load any network drivers (saves memory)
#SUPPRESS_OTHERS=yes

ifconfig $MDEV up
iwconfig $MDEV essid xxxxxxxx_xxxx key "xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx"

which is pretty much the same as earlier (whereas it worked with ext3-boot). The LED on my network adapter is lit on green, I do not recall homever what was the case with it earlier. When I hard-reboot the WD TV, I get "No IP" message. Any ideas on how to deal with it? I don't want to get back to ext3-boot.

///Disregard that, I just moved the old app pack, along with old conf, and it works.

///^Disregard that, while I received the IP, I can't connect via SSH/FTP "ECONNREFUSED - Connection refused by server". Plus the LED started blinking instead, slowly.

//^Disregard -that-, old version works fine, but I didn't read enough to find out additional app packs are needed for ssh/ftp.
Title: Re: *experimental* wireless usb support package
Post by: NorthernComfort on October 05, 2009, 05:47:31 PM
I'm not a rich person, but willing to pay $10 CAD paypal to first person who can get my TrendNet TEW-644UB working properly on my WDTV.  Offer good until Wednesday October 07 at 9AM EST, after which the offer is revoked and I return the device to Costco ($33 CAD), and I buy something better (maybe even punch a few holes in the wall and run 100M ethernet).
Title: Re: *experimental* wireless usb support package
Post by: ionutm80 on October 05, 2009, 11:56:44 PM
Hi guys,

I have a problem which I haven't succeeded in solving for almost 3 weeks.
I could FTP, telnet to WDTV; I could share from my PC through CIFS, NFS. I can even share through Samba the files on the WD Passport attached to my WDTV except for NFS share – here I get an error saying : exportfs: Warning /tmp/media/usb/USB2/.806…COA does not support NFS export. The WD Passport attached to WDTV is partitioned as NTFS.
Does anybody know where this problem comes?
Is it because the drive attached to WDTV is NTFS?

Regards,

IonutM.
Title: Re: *experimental* wireless usb support package
Post by: NorthernComfort on October 07, 2009, 12:29:59 AM
Well, good news for me.  I bought a different device (Azio using the rt73 chipset), and after a short battle, I won.  Many thanks to all the people who made this possible.
Title: Re: *experimental* wireless usb support package
Post by: microcens on October 12, 2009, 07:51:26 AM
can soneone help me please tell me how to make a d-link dwl 122 to work with my wdtv?i cant get ip




Jan  1 00:00:03 (none) syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:04 (none) user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:04 (none) user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #2 PREEMPT Mon Sep 15 20:20:41 CST 2008
Jan  1 00:00:04 (none) user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:04 (none) user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:04 (none) user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:04 (none) user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:04 (none) user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:04 (none) user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:04 (none) user.warn kernel: Determined physical RAM map:
Jan  1 00:00:04 (none) user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:04 (none) user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:04 (none) user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:04 (none) user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:04 (none) user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:04 (none) user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:04 (none) user.warn kernel: Built 1 zonelists
Jan  1 00:00:04 (none) user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:04 (none) user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:04 (none) user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:04 (none) user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:04 (none) user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:04 (none) user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:04 (none) user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:04 (none) user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:04 (none) user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:04 (none) user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:04 (none) user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:04 (none) user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:04 (none) user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:04 (none) user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:04 (none) user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:04 (none) user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:04 (none) user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:04 (none) user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:04 (none) user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:04 (none) user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:04 (none) user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:04 (none) user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:04 (none) user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:04 (none) user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:04 (none) user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:04 (none) user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:04 (none) user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:04 (none) user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:04 (none) user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:04 (none) user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:04 (none) user.info kernel: Initializing Cryptographic API
Jan  1 00:00:04 (none) user.info kernel: io scheduler noop registered
Jan  1 00:00:04 (none) user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:04 (none) user.info kernel: io scheduler deadline registered
Jan  1 00:00:04 (none) user.info kernel: io scheduler cfq registered
Jan  1 00:00:04 (none) user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:04 (none) user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:04 (none) user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:04 (none) user.notice root: Displaying detected USB devices...
Jan  1 00:00:04 (none) user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:04 (none) user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:04 (none) user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:04 (none) user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:04 (none) user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:04 (none) user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:04 (none) user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:04 (none) user.notice kernel: number of CFI chips: 1
Jan  1 00:00:04 (none) user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:04 (none) user.notice kernel: Using physmap partition definition
Jan  1 00:00:04 (none) user.notice kernel: Adding partition #1-#5
Jan  1 00:00:04 (none) user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:04 (none) user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:04 (none) user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:04 (none) user.notice root:  [07d1:3c03] 1-1( 2.00,480m) 802.11 bg WLAN
Jan  1 00:00:04 (none) user.notice root:  [08ec:2038] 1-2( 2.00,480m) DataTraveler 2.0/0B21CB6003839A9D
Jan  1 00:00:05 (none) user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:05 (none) user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:05 (none) user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:05 (none) user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:05 (none) user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:05 (none) user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:05 (none) user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:05 (none) user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:05 (none) user.warn kernel: TangoX USB initializing...
Jan  1 00:00:05 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:00:05 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:00:05 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:00:05 (none) user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:00:05 (none) user.info kernel: hub 1-0:1.0: USB hub foun
Jan  1 00:00:05 (none) user.info kernel: d
Jan  1 00:00:05 (none) user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:00:05 (none) user.warn kernel: TangoX USB was initialized.
Jan  1 00:00:05 (none) user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:00:05 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:00:05 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:00:05 (none) user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:00:05 (none) user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:00:05 (none) user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:00:05 (none) user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:00:05 (none) user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:05 (none) user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:05 (none) user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:05 (none) user.debug kernel: usb-storage: device found at 3
Jan  1 00:00:05 (none) user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:05 (none) user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:05 (none) user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:05 (none) user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:05 (none) user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:05 (none) user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:05 (none) user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:05 (none) user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:05 (none) user.info kernel: TCP reno registered
Jan  1 00:00:05 (none) user.info kernel: TCP bic registered
Jan  1 00:00:05 (none) user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:05 (none) user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:05 (none) user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:06 (none) user.notice kernel:   Vendor: Kingston  Model: DataTraveler 2.0  Rev: 6.50
Jan  1 00:00:06 (none) user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:00:06 (none) user.notice kernel: SCSI device sda: 984063 512-byte hdwr sectors (504 MB)
Jan  1 00:00:06 (none) user.notice kernel: sda: Write Protect is off
Jan  1 00:00:06 (none) user.debug kernel: sda: Mode Sense: 45 00 00 08
Jan  1 00:00:06 (none) user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:06 (none) user.notice kernel: SCSI device sda: 984063 512-byte hdwr sectors (504 MB)
Jan  1 00:00:06 (none) user.notice kernel: sda: Write Protect is off
Jan  1 00:00:06 (none) user.debug kernel: sda: Mode Sense: 45 00 00 08
Jan  1 00:00:06 (none) user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:06 (none) user.info kernel:  sda: sda1
Jan  1 00:00:06 (none) user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:06 (none) user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:06 (none) user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:06 (none) user.notice root: INIT: mounting app binaries...
Jan  1 00:00:07 (none) user.notice root: DEVICE /dev/sda1 CONNECTED
Jan  1 00:00:07 (none) user.notice root: log-saver app found
Jan  1 00:00:08 (none) user.notice root: Mounting /tmp/mnt/sda1/log-saver.app.bin at /apps/log-saver
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=68, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=1252, limit=8
Jan  1 00:00:08 (none) user.info kernel: attempt to access beyond end of device
Jan  1 00:00:08 (none) user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:08 (none) user.warn kernel: UDF-fs: No partition found (1)
Jan  1 00:00:08 (none) daemon.info utelnetd[381]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:00:08 (none) user.notice root: Mounting opt.bin at /opt
Jan  1 00:00:08 (none) user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:09 (none) user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:00:09 (none) user.info kernel: EXT3 FS on loop1,
Jan  1 00:00:09 (none) user.info kernel: internal journal
Jan  1 00:00:09 (none) user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:00:09 (none) user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:00:09 (none) user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:09 (none) user.notice root: Mounting /tmp/mnt/sda1/wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:09 (none) user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:09 (none) user.notice root: adjusting LIBPATH
Jan  1 00:00:12 (none) user.notice root: adjusting PATH
Jan  1 00:00:12 (none) user.notice root: Path set to /opt/sbin:/opt/bin:/apps/wireless-mod-wdlxtv/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:14 (none) user.notice root: Inserting the modules...
Jan  1 00:00:15 (none) user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:15 (none) user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:15 (none) user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:00:23 (none) user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:00:23 (none) user.warn kernel: em8xxx0 [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:00:24 (none) user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:00:24 (none) user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c9285a54
Jan  1 00:00:24 (none) user.warn kernel: em8xxx [/home/william/WDTV/WDTV_Golden_1.00.01/core_repos/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:00:25 (none) user.notice root: Generated new defaultHOST=WDTV-22f67
Jan  1 00:00:28 (none) user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:28 (none) user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:28 (none) user.info kernel: usbcore: registered new driver asix
Jan  1 00:00:28 (none) user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:00:28 (none) user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:00:29 (none) user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:00:29 (none) user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:00:29 (none) user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:00:29 (none) user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:00:29 (none) user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:00:29 (none) user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:00:29 (none) user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:29 (none) user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:00:30 (none) user.info kernel: usbcore: registered new driver catc
Jan  1 00:00:30 (none) user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:00:30 (none) user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:30 (none) user.info kernel: Loading wireless extentions module...
Jan  1 00:00:30 (none) user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:38 (none) user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:00:38 (none) user.debug kernel: ir: Enable RC5 decoder (0x00000000)


Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="χχχ"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="χχχ"
}

Quote
##
# Network configuration file

#You can override the hostname here:

HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
# MTU=9000

#
# Dynamic IP Configuration:

# DHCP=yes

ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf


#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.65
GW=192.168.1.254
NM=255.255.255.0
DNS1=212.216.112.222
DNS2=212.216.172.62

#
# Optional:  specify time server host:

#NTP=pool.ntp.org
Title: Re: *experimental* wireless usb support package
Post by: ukasho on October 16, 2009, 06:32:15 AM
Hello!

Could anybody help me with configuration of file wpa_supplicant.conf. When I connect WD without security options it works. But when I set security options: WPA-PSK[TKIP]+WPA2-PSK[AES] it didn't work. Please help with configuration of file wpa_supplicant.conf for these security options. I have NETGEAR WGR614 router and Philips SNU5600 (zd1211b) wireless card.

Regards

ukasho
Title: Re: *experimental* wireless usb support package
Post by: sakure on October 20, 2009, 07:01:00 AM
Hi there!!

I'm trying to get Wifi connected with my Zydas dongle, it's supposed to be a zd1211b.

I've tryed 7 possible configurations (mix of conf files and libraries), and in the cases I get it working it does it very bad, very slow and with disconnections (testing telnet, pureftp and webserver).

I'll put here a slice of these tests...., if you can help me tunning it fine, I'll will thank you a lot.

BREAKED INTO MORE POSTS

In every test I use the same "wpa_supplicant.conf" file:

Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="+++++ MYNETWORKNAME +++++"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="+++++ theKey ++++"
}

Test 1

Wifi Library: wireless-mod-wdlxtv.app.bin

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=9000
insmod /tmp/mnt/sda1/[b]zd1211b.ko[/b]
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
[b]DHCP=yes[/b]

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:21 WDTV-4d64f user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:21 WDTV-4d64f user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:21 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:21 WDTV-4d64f user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:22 WDTV-4d64f user.notice root: xmounted /dev/sda1
Jan  1 00:00:22 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:25 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:00:41 WDTV-4d64f user.warn kernel: zd1211b: Unknown symbol wireless_send_event
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:02 WDTV-4d64f user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:02 WDTV-4d64f user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:02 WDTV-4d64f user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:04 WDTV-4d64f user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:06 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:06 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:07 WDTV-4d64f user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: vendor_id = 0ace
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: product_id = 1211
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: USB 2.0 Host
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: Release Ver = 4330
Jan  1 00:01:10 WDTV-4d64f user.notice kernel: EEPROM Ver = 4810
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:10 WDTV-4d64f user.err kernel: PA type: 0
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: AiroHa AL2230RF
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:01:10 WDTV-4d64f user.debug kernel: zd1205_config: EEP(HWFeature)=0x0
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:01:10 WDTV-4d64f user.warn kernel: Region:48
Jan  1 00:01:10 WDTV-4d64f user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:10 WDTV-4d64f user.notice root: net.agent:  Called for eth0
Jan  1 00:01:33 WDTV-4d64f user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:01:34 WDTV-4d64f user.debug kernel: *** Block Non-EAPol packet before key installed:0800
Jan  1 00:01:37 WDTV-4d64f user.debug kernel: *** Block Non-EAPol packet before key installed:0800
....


RESULTS: It works with poor performance.



Test 2

Wifi Library: wireless-mod-wdlxtv.app.bin

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /boot/[b]zd1211.ko[/b]  --> Just testing if its the other driver
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
[b]DHCP=no[/b]
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
DNS2=205.171.3.65

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:22 WDTV-4d64f user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:22 WDTV-4d64f user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:22 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:22 WDTV-4d64f user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:22 WDTV-4d64f user.notice root: xmounted /dev/sda1
Jan  1 00:00:23 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:26 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:26 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:26 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:03 WDTV-4d64f user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:03 WDTV-4d64f user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:03 WDTV-4d64f user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:04 WDTV-4d64f user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:07 WDTV-4d64f user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:08 WDTV-4d64f user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:08 WDTV-4d64f user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:09 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:09 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:09 WDTV-4d64f user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
....


RESULTS: It didn't work at all.

Title: Re: *experimental* wireless usb support package
Post by: sakure on October 20, 2009, 07:04:19 AM
CONTINUE:

Test 3

Wifi Library: wireless-mod-wdlxtv.app.bin

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /tmp/mnt/sda1/[b]zd1211.ko[/b]
[b]blacklist zd1211b[/b]
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
DHCP=no
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
DNS2=205.171.3.65

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:20 WDTV-4d64f user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:20 WDTV-4d64f user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:20 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:21 WDTV-4d64f user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:21 WDTV-4d64f user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:22 WDTV-4d64f user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:22 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:26 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:02 WDTV-4d64f user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:02 WDTV-4d64f user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:03 WDTV-4d64f user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:03 WDTV-4d64f user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:04 WDTV-4d64f user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:04 WDTV-4d64f user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:04 WDTV-4d64f user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:05 WDTV-4d64f user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:06 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:06 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:08 WDTV-4d64f user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
....


RESULTS:  It didn't work at all. (same than before)



Test 4

Wifi Library: wireless-mod-wdlxtv.app.bin

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /tmp/mnt/sda1/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
DHCP=no
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
DNS2=205.171.3.65

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:22 WDTV-4d64f user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:22 WDTV-4d64f user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:22 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:22 WDTV-4d64f user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:23 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:26 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:26 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:26 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:00:42 WDTV-4d64f user.warn kernel: zd1211b: Unknown symbol wireless_send_event
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:04 WDTV-4d64f user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:04 WDTV-4d64f user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:04 WDTV-4d64f user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:06 WDTV-4d64f user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:06 WDTV-4d64f user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:06 WDTV-4d64f user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:07 WDTV-4d64f user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:07 WDTV-4d64f user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:08 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:08 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:09 WDTV-4d64f user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: vendor_id = 0ace
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: product_id = 1211
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: USB 2.0 Host
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: Release Ver = 4330
Jan  1 00:01:12 WDTV-4d64f user.notice kernel: EEPROM Ver = 4810
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:12 WDTV-4d64f user.err kernel: PA type: 0
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: AiroHa AL2230RF
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:01:12 WDTV-4d64f user.debug kernel: zd1205_config: EEP(HWFeature)=0x0
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:01:12 WDTV-4d64f user.warn kernel: Region:48
Jan  1 00:01:12 WDTV-4d64f user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:12 WDTV-4d64f user.notice root: net.agent:  Called for eth0
Jan  1 00:01:34 WDTV-4d64f user.notice root: [b]Testing static IP assignment[/b]...
Jan  1 00:01:47 WDTV-4d64f user.notice root: Switching to resolution 225x300 in video thumbmail mode
Jan  1 00:01:48 WDTV-4d64f daemon.info utelnetd[2388]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:01:49 WDTV-4d64f user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:49 WDTV-4d64f user.notice root: [b]IP Assignment failed.  Trying DHCP[/b]
Jan  1 00:01:50 WDTV-4d64f user.notice root: net.agent: Using pool.ntp.org to set system time
Oct 19 22:15:05 WDTV-4d64f user.notice root: Device eth0 configged as 192.168.1.128/192.168.1.1/255.255.255.0
....


RESULTS: It works with poor performance.[/b], in this test STATIC-IP configuration didn't work!!!, I don't know why...., I've used the same net conf of my other computer (of course with different IP).



Test 5

Wifi Library: wireless-mod.app.bin

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /tmp/mnt/sda1/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
DHCP=no
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
NTP=pool.ntp.org
[b]SUPPRESS_OTHERS=yes[/b]

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:22 WDTV-4d64f user.notice root: wireless-mod app found
Jan  1 00:00:22 WDTV-4d64f user.notice root: Mounting wireless-mod.app.bin at /apps/wireless-mod
Jan  1 00:00:22 WDTV-4d64f user.notice root: xmounted /dev/sda1
Jan  1 00:00:22 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:23 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:24 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:24 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:24 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:01 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: zd1201: Unknown symbol release_firmware
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: zd1201: Unknown symbol request_firmware
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: vendor_id = 0ace
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: product_id = 1211
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: USB 2.0 Host
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: Release Ver = 4330
Jan  1 00:01:01 WDTV-4d64f user.notice kernel: EEPROM Ver = 4810
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:01 WDTV-4d64f user.err kernel: PA type: 0
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: AiroHa AL2230RF
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:01:01 WDTV-4d64f user.debug kernel: zd1205_config: EEP(HWFeature)=0x0
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:01:01 WDTV-4d64f user.warn kernel: Region:48
Jan  1 00:01:01 WDTV-4d64f user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:02 WDTV-4d64f user.notice root: net.agent:  Called for eth0
Jan  1 00:01:08 WDTV-4d64f user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:08 WDTV-4d64f user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:08 WDTV-4d64f user.warn kernel: rtusb init --->
Jan  1 00:01:08 WDTV-4d64f user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:09 WDTV-4d64f user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:21 WDTV-4d64f daemon.info utelnetd[1901]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:01:22 WDTV-4d64f user.notice root: Switching to resolution 225x300 in video thumbmail mode
Jan  1 00:01:24 WDTV-4d64f user.notice root: Testing static IP assignment...
Jan  1 00:01:29 WDTV-4d64f user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:29 WDTV-4d64f user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:39 WDTV-4d64f user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:39 WDTV-4d64f user.notice root: IP Assignment failed.  Trying DHCP
Jan  1 00:01:43 WDTV-4d64f user.notice root: net.agent: Using pool.ntp.org to set system time
Oct 19 22:35:02 WDTV-4d64f user.notice root: Device eth0 configged as 192.168.1.128/192.168.1.1/255.255.255.0
....


RESULTS:  It works with poor performance.[/b], in this test STATIC-IP configuration didn't work!!!, I don't know why...., I've used the same net conf of my other computer (of course with different IP). SAME AS BEFORE



Test 6

Wifi Library: NO LIBRARY, Used only the driver: zd1211b.ko

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /tmp/mnt/sda1/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
DHCP=no
IP=192.168.1.10
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
NTP=pool.ntp.org
SUPPRESS_OTHERS=yes

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:38 WDTV-4d64f user.warn kernel: zd1211b: Unknown symbol wireless_send_event
....


RESULTS:  It didn't work at all.


Test 7

Wifi Library: wireless-mod-wdlxtv.app.bin as in the beginning

net.config (comments removed):
Code: [Select]
HOST=wdtv
MTU=1492
insmod /tmp/mnt/sda1/zd1211b.ko
blacklist zd1211
sleep 10
ifconfig $MDEV up
wpa_supplicant -B w -D otus -i $MDEV -c /tmp/mnt/sda1/wpa_supplicant.conf
sleep 10
DHCP=no
[b]IP=192.168.1.101[/b]   ---> Changed the IP....
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
NTP=pool.ntp.org
SUPPRESS_OTHERS=yes

messages.txt (slice):
Code: [Select]
.....
Jan  1 00:00:20 WDTV-4d64f user.notice root: wireless-mod-wdlxtv app found
Jan  1 00:00:20 WDTV-4d64f user.notice root: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:20 WDTV-4d64f user.notice root: xmounted /dev/sda1
Jan  1 00:00:20 WDTV-4d64f user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:21 WDTV-4d64f user.notice root:  [0ace:1211] 1-2( 2.00,480m) USB2.0 WLAN
Jan  1 00:00:22 WDTV-4d64f user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:22 WDTV-4d64f user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:22 WDTV-4d64f user.notice root: adjusting LIBPATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: adjusting PATH
Jan  1 00:00:25 WDTV-4d64f user.notice root: Path set to /apps/wireless-mod-wdlxtv/bin:/apps/samba/bin:/apps/pure-ftpd/bin:/apps/event-osd/bin:/apps/LaurentG/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:26 WDTV-4d64f user.notice root: starting mount.watch patched by Ernis
Jan  1 00:00:41 WDTV-4d64f user.warn kernel: zd1211b: Unknown symbol wireless_send_event
Jan  1 00:01:02 WDTV-4d64f user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:02 WDTV-4d64f user.info kernel: Loading wireless extentions module...
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: vendor_id = 0ace
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: product_id = 1211
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: USB 2.0 Host
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: Release Ver = 4330
Jan  1 00:01:03 WDTV-4d64f user.notice kernel: EEPROM Ver = 4810
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: Finish download Firmware. Ready to reboot
Jan  1 00:01:03 WDTV-4d64f user.err kernel: PA type: 0
Jan  1 00:01:03 WDTV-4d64f user.warn kernel: AiroHa AL2230RF
Jan  1 00:01:04 WDTV-4d64f user.warn kernel: ieee80211_dirmcast_attach
Jan  1 00:01:04 WDTV-4d64f user.debug kernel: zd1205_config: EEP(HWFeature)=0x0
Jan  1 00:01:04 WDTV-4d64f user.warn kernel: AllowedChannel = 000107ff
Jan  1 00:01:04 WDTV-4d64f user.warn kernel: Region:48
Jan  1 00:01:04 WDTV-4d64f user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:04 WDTV-4d64f user.notice root: net.agent:  Called for eth0
Jan  1 00:01:25 WDTV-4d64f user.notice root: Testing static IP assignment...
Jan  1 00:01:39 WDTV-4d64f daemon.info utelnetd[2131]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:01:40 WDTV-4d64f user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:41 WDTV-4d64f user.notice root: IP Assignment failed.  Trying DHCP
Jan  1 00:01:41 WDTV-4d64f user.notice root: Switching to resolution 225x300 in video thumbmail mode
Jan  1 00:01:42 WDTV-4d64f user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:42 WDTV-4d64f user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:44 WDTV-4d64f user.notice root: net.agent: Using pool.ntp.org to set system time
Oct 19 22:54:27 WDTV-4d64f user.notice root: Device eth0 configged as 192.168.1.128/192.168.1.1/255.255.255.0
....


RESULTS:   It works with poor performance.[/b], in this test STATIC-IP configuration didn't work!!!, I don't know why...., I've used the same net conf of my other computer (of course with different IP).


So....., Sorry for this long post...., Any clue on this?, Why is the performance so poor?, Why didn't StaticIP assignement work?


Thank you a lot!!!

Bye.
Title: Re: *experimental* wireless usb support package
Post by: microcens on October 29, 2009, 03:10:31 AM
i have setup my dwl-g122 rev.C dongle to work with an open wifi network but i cant make it work with wep or wap.Can someone help?


an 1 00:00:48 WDTV-982c8 user.notice root: net.agent: Called for rausb0
Jan 1 00:00:48 WDTV-982c8 user.info kernel: usbcore: registered new driver rt73
Jan 1 00:00:53 WDTV-982c8 user.warn kernel: => usb_rtusb_open
Jan 1 00:00:54 WDTV-982c8 user.notice root: Testing static IP assignment...
Jan 1 00:00:55 WDTV-982c8 daemon.info utelnetd[1514]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan 1 00:00:57 WDTV-982c8 user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan 1 00:00:57 WDTV-982c8 user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan 1 00:01:08 WDTV-982c8 user.notice mount.watch: Unmounting official device /tmp/media/usb/sda1
Jan 1 00:01:09 WDTV-982c8 user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan 1 00:01:09 WDTV-982c8 user.notice root: IP Assignment failed. Trying DHCP
Title: Re: *experimental* wireless usb support package
Post by: jpdragon on October 29, 2009, 08:59:31 PM
Does this package compatible with Linksys WUSB54G version 4 Wireless USB adapter?
Title: Re: *experimental* wireless usb support package
Post by: daskino on November 03, 2009, 02:10:43 AM
Did some of you work out to create the driver for RTL8191S(U) ?  I myself have a xtreamer wifi adatper.
 i would like to use on the wdtv, In the startup file it id the adapter as RTL8191S chipset.
Title: Re: *experimental* wireless usb support package
Post by: kimera on November 21, 2009, 12:38:21 AM
hello guys. I have a little problem.

sorry for my english :-)

i have a tp-link  TL-WN321g wireless key, it's work with ext3-boot 0.9.2?? P.S i have the last firmware on my WDTV

The chipset of this key is ralink 2571. What .dat files i can use ? rt2570 or rt73???

thx for all
Title: Re: *experimental* wireless usb support package
Post by: gcs on November 21, 2009, 12:43:17 PM
Hello,

It took all the afternoon long to read half of this interesting, but long long post.
I beg your pardon, I'm not an expert, therefore I've not understood much.
Here is my simple question: Is somewhere a simple step by step guide about this topic?
I really would like to make my WD-TV working Wireless, but I dont' want to bore you with newbie questions.

Thanks a lot in advance,

John B.
Title: Re: *experimental* wireless usb support package
Post by: kimera on November 23, 2009, 12:23:48 AM
anyone can help me with tp-link TL-WN321G??

this is my Messages.txt, i run the latest ext3-boot

Code: [Select]
Jan  1 00:00:20 wdtv syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:20 wdtv user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:20 wdtv user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:20 wdtv user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:20 wdtv user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:20 wdtv user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:20 wdtv user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:20 wdtv user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:20 wdtv user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:20 wdtv user.warn kernel: Determined physical RAM map:
Jan  1 00:00:20 wdtv user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:20 wdtv user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:20 wdtv user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:20 wdtv user.notice root: Displaying detected USB devices...
Jan  1 00:00:21 wdtv user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:22 wdtv user.notice root:  [0471:082b] 1-2( 2.00,480m) USB Flash Drive/AA04012700007588
Jan  1 00:00:22 wdtv user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:22 wdtv user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:23 wdtv user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:23 wdtv user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:23 wdtv user.warn kernel: Built 1 zonelists
Jan  1 00:00:24 wdtv user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:24 wdtv daemon.info utelnetd[523]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:00:24 wdtv user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:24 wdtv user.notice root: INIT: mounting app binaries...
Jan  1 00:00:25 wdtv user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:25 wdtv user.notice root: Mounting /boot/wireless-mod-rt.app.bin at /apps/wireless-mod-rt
Jan  1 00:00:26 wdtv user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:26 wdtv user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:27 wdtv user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:27 wdtv user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:28 wdtv user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:28 wdtv user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:28 wdtv user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:28 wdtv user.notice root: Path set to /apps/wireless-mod-rt/bin:/boot/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:29 wdtv user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:30 wdtv authpriv.info dropbear[624]: Running in background
Jan  1 00:00:31 wdtv user.notice root: vfat: Waiting for 10B0-2075 to mount
Jan  1 00:00:31 wdtv user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:32 wdtv user.notice root: Polling detected drives...
Jan  1 00:00:32 wdtv user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:33 wdtv user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:34 wdtv user.notice root: Waiting for /dev/sda1 to come online (UUID=10B0-2075)...
Jan  1 00:00:34 wdtv user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:35 wdtv user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:35 wdtv user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:36 wdtv user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:36 wdtv user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:37 wdtv user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:37 wdtv user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:38 wdtv user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:38 wdtv user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:39 wdtv user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:39 wdtv user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:39 wdtv user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:40 wdtv user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:40 wdtv user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:42 wdtv user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:43 wdtv user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:44 wdtv user.notice root: wireless-mod-rt: Starting..
Jan  1 00:00:44 wdtv user.info kernel: Initializing Cryptographic API
Jan  1 00:00:45 wdtv user.notice root: wireless-mod-rt: Installing new device configs to /etc/mdev.conf
Jan  1 00:00:45 wdtv user.info kernel: io scheduler noop registered
Jan  1 00:00:46 wdtv user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:46 wdtv user.info kernel: io scheduler deadline registered
Jan  1 00:00:47 wdtv user.info kernel: io scheduler cfq registered
Jan  1 00:00:47 wdtv user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:47 wdtv user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:48 wdtv user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:48 wdtv user.notice root: wireless-mod-rt: WLAN_LOAD=rt73.ko, config=/boot/rt73sta.dat
Jan  1 00:00:48 wdtv user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:49 wdtv user.notice root: wireless-mod-rt: Copying /boot/rt73sta.dat to /etc
Jan  1 00:00:49 wdtv user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:50 wdtv user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:50 wdtv user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:51 wdtv user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:51 wdtv user.notice root: wireless-mod-rt: Installing rt73.ko firmware
Jan  1 00:00:51 wdtv user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:52 wdtv user.notice root: wireless-mod-rt: Install modules /apps/wireless-mod-rt/modules/rt73.ko
Jan  1 00:00:52 wdtv user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:53 wdtv user.notice kernel: number of CFI chips: 1
Jan  1 00:00:53 wdtv user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:54 wdtv user.notice kernel: Using physmap partition definition
Jan  1 00:00:56 wdtv user.notice kernel: Adding partition #1-#5
Jan  1 00:00:58 wdtv user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:58 wdtv user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:59 wdtv daemon.notice statd[1225]: Version 1.1.5 Starting
Jan  1 00:00:59 wdtv user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:59 wdtv daemon.notice statd[1225]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:00 wdtv user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:01:01 wdtv user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:01:01 wdtv user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:01:02 wdtv user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:01:02 wdtv user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:01:02 wdtv user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:01:03 wdtv user.warn kernel: TangoX USB initializing...
Jan  1 00:01:03 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:01:04 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Jan  1 00:01:05 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:01:05 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:01:06 wdtv user.info kernel: hub 1-0:1.0: USB hub fou
Jan  1 00:01:06 wdtv user.info kernel: nd
Jan  1 00:01:07 wdtv user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:01:08 wdtv user.warn kernel: TangoX USB was initialized.
Jan  1 00:01:08 wdtv user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:01:09 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:01:09 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:01:10 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:01:10 wdtv user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:01:10 wdtv user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:01:11 wdtv user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:01:11 wdtv user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:01:12 wdtv user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:01:12 wdtv user.debug kernel: usb-storage: device found at 2
Jan  1 00:01:12 wdtv user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:01:13 wdtv user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:01:15 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:01:15 wdtv user.info kernel: USB Mass Storage support registered.
Jan  1 00:01:16 wdtv user.notice root: Now mounted:
Jan  1 00:01:16 wdtv user.info kernel: NET: Registered protocol family 2
Jan  1 00:01:16 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:17 wdtv user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:01:17 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:17 wdtv user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:01:18 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:18 wdtv user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:01:18 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:19 wdtv user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:01:19 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:20 wdtv user.info kernel: TCP reno registered
Jan  1 00:01:20 wdtv user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:20 wdtv user.info kernel: TCP bic registered
Jan  1 00:01:20 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:01:21 wdtv user.info kernel: NET: Registered protocol family 1
Jan  1 00:01:21 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:21 wdtv user.info kernel: NET: Registered protocol family 17
Jan  1 00:01:22 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:01:22 wdtv user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:01:23 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:23 wdtv user.notice kernel:   Vendor: Philips   Model: USB Flash Drive   Rev: 1100
Jan  1 00:01:24 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:24 wdtv user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:01:24 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:24 wdtv user.notice kernel: SCSI device sda: 1981440 512-byte hdwr sectors (1014 MB)
Jan  1 00:01:25 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:25 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:01:25 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:26 wdtv user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:01:26 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod-rt type ext3 (rw,data=ordered)
Jan  1 00:01:26 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:01:27 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB2/10B0-2075 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:27 wdtv user.notice kernel: SCSI device sda: 1981440 512-byte hdwr sectors (1014 MB)
Jan  1 00:01:28 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:01:28 wdtv user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:01:29 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:01:29 wdtv user.info kernel:  sda: sda1
Jan  1 00:01:29 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:01:30 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:01:30 wdtv user.debug kernel: usb-storage: device scan complete
Jan  1 00:01:30 wdtv user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:01:30 wdtv user.info kernel: EXT3 FS on loop1, internal journal
Jan  1 00:01:31 wdtv user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:01:31 wdtv user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:01:31 wdtv user.warn kernel: em8xxx: no version for "llad_open" found: kernel tainted.
Jan  1 00:01:32 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:01:32 wdtv user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:01:32 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:01:33 wdtv user.warn kernel: mumk_register_tasklet: (0) tasklet c401e000 status @c938aa24
Jan  1 00:01:33 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:01:33 wdtv user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:01:34 wdtv user.info kernel: EXT3 FS on loop0, internal journal
Jan  1 00:01:34 wdtv user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:01:34 wdtv user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:35 wdtv user.info kernel: Loading wireless extentions module...
Jan  1 00:01:35 wdtv user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:35 wdtv user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:35 wdtv user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:36 wdtv user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:36 wdtv user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:36 wdtv user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:37 wdtv user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:37 wdtv user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:37 wdtv user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:38 wdtv user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:38 wdtv user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:38 wdtv user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:39 wdtv user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:39 wdtv user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:39 wdtv user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:40 wdtv user.info kernel: usbcore: registered new driver cdc_ether
Jan  1 00:01:40 wdtv user.info kernel: usbcore: registered
Jan  1 00:01:40 wdtv user.info kernel:  new driver cdc_subset
Jan  1 00:01:41 wdtv user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:41 wdtv user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:41 wdtv user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:42 wdtv user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:42 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:44 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:45 wdtv user.debug kernel: ir: Enable RC5 decoder (0x80000000)
Jan  1 00:01:46 wdtv user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:01:47 wdtv user.warn kernel: idVendor = 0x148f, idProduct = 0x2573
Jan  1 00:02:31 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:02:35 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:02:35 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:02:35 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:04:03 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:04:29 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Jan  1 00:04:38 wdtv user.warn kernel: program dmaosd is using a deprecated SCSI ioctl, please convert it to SG_IO
Title: Re: *experimental* wireless usb support package
Post by: banchang on November 24, 2009, 06:37:28 AM
I seem to have loaded the b-rad.cc update ok, as I get the IP on the opening screen when powered on, but it says

IP: No IP

& then moves on to the standard opening screen with Video, Photos, Settings etc

I'm typing this off my laptop right now, so wifi is working. Thoughts ?
Title: Re: *experimental* wireless usb support package
Post by: banchang on November 25, 2009, 04:45:54 AM
i have setup my dwl-g122 rev.C dongle to work with an open wifi network

Can you help me with mine, also open , but can't get it to work ?

I have the D-Link wifi dongle DWL-G122 Ver C1.
Firmware 1.02.11 WDLXTV-0.5.7

Message I get on the 'About' screen is 'WDTV-20524 : no IP'

Dongle's Link light is flashing, but Act light is off.

Implemented this http://b-rad.cc/900/wdlxtv-app-pack-wireless-mod-wdlxtv/#more-900 (http://b-rad.cc/900/wdlxtv-app-pack-wireless-mod-wdlxtv/#more-900)
to the letter, or so I thought

Wifi working well, confirmed.

Net.config file reads as follows :

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:
DHCP=yes

#
# Static IP Configuration: (only if not DHCP)
#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65
ifconfig $MDEV up
iwconfig $MDEV essid myroutername

As I have read that different dongle chipsets require different syntax in config.net, I have tried both

ifconfig rausb0 up
iwconfig rausb0 essid myroutername

and

ifconfig $MDEV up
iwconfig $MDEV essid myroutername

& still Link light flashes, but Act light is off, & continue to get No IP

Help !

Title: Re: *experimental* wireless usb support package
Post by: c3f8 on December 16, 2009, 03:23:22 PM
Hi there,

I just tried several ways to put my wireless working but i without success.
Hope someone can help me.

My software
ext3-boot 0.9.2
wireless-mod 0.3

My hardware
wdtv
belkin usb wireless card model nº F5D7050
512 MB flash drive for boot

Files/folders in flash drive
.wdtv (folder)
www (folder)
Changelog (file)
messages.txt (file)
net.config (file)
net.mounts (file)
root.bin (file)
wdtv.bin (file)
wdtv.ver (file)
wireless-mod.app.bin (file)

My net.config file (i ignored the comments)
Code: [Select]
HOST=wdtv
ifconfig $MDEV up
iwconfig $MDEV essid HoMiX key "s:0079449AAE"
DHCP=yes

Last lines of my messages.txt
Code: [Select]
Jan  1 00:00:37 wdtv user.debug kernel: Update CardSetting
Jan  1 00:00:37 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=yes IP= GW=
Jan  1 00:00:37 wdtv user.notice root: net.agent: No IP provided, doing DHCP
Jan  1 00:00:38 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:00:38 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:00:39 wdtv user.warn kernel: rtusb init --->
Jan  1 00:00:39 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:00:39 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:00:44 wdtv daemon.notice statd[1225]: Version 1.1.5 Starting
Jan  1 00:00:44 wdtv daemon.notice statd[1225]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:00:48 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:00:48 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:00:56 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:00:57 wdtv user.notice root: Now mounted:
Jan  1 00:00:57 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:00:57 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:00:57 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:00:57 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:00:57 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:00:57 wdtv user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:00:57 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:00:57 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:00:57 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:00:57 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:00:57 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:00:57 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:00:57 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:00:57 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:00:57 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:00:57 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB2/90FB-CA8F type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)

Sorry for this massive post.
I really need help.

Thanks all,
Hugs from Portugal
Title: Re: *experimental* wireless usb support package
Post by: shemilio on December 18, 2009, 07:14:33 PM
anyone can help me with tp-link TL-WN321G??

this is my Messages.txt, i run the latest ext3-boot


I have TP-link 321G running in WDTV 1 + 1.03.01_B-RAD.CC_WDLXTV-0.5.8.1  + wireless-mod-rt.app.bin-1.31.zip

just adding in net.config
# WLAN

#one of rt61sta.dat, rt73sta.dat, RT2400.dat, RT2500STA.dat, RT2570STA.dat, RT2870STA.dat (used by rt3070 as well)
WLAN_CFG=rt73sta.dat
#one of rt61.ko, rt73.ko, rt2400.ko, rt2500.ko, rt2570.ko, rt2870sta.ko, rt3070sta.ko
WLAN_LOAD=rt73.ko
#need to bring up device?
WLAN_UP=yes
#time to sleep while waiting for wireless association
WLAN_SLEEP=5

and creating a suitable rt73sta.dat.

Cheers,
Title: Re: *experimental* wireless usb support package
Post by: deantc on December 24, 2009, 08:43:59 AM
Hi guys this is my first post just wanted to share my findings.
Firstly I'd like to thank the likes of Zorander, B-RAD, Razmus, Disco and smartp for the time and effort to create these lovely extras.

I had a spare Linksys WUSB54GC so rather than purchase a USB Ethernet Adapter I wanted to get my EXT3boot(initially WDLXTV but wireless would not work at all) to function with this wireless adapter.

Managed to get wireless working using wireless-mod-rt.app.bin v1.2 "WEP only". (Driver RT73)
It was stable for days with low transfer such as SSH and Webserver.
BUT as soon as I started to use it to stream movies or move large files it would drop the connection after a few minutes. The driver seemed to be active but the wireless device was unable to re-associate with access point. WDTV and my Wireless Access Point are less than 3ft apart so not a distance issue.

Unfortunately I gave up and bought a Newlink USB Ethernet adapter for £9, my WDTV seems to boot up much quicker when its not loading the wireless stuff and so far connection hasn't dropped.


Title: Re: *experimental* wireless usb support package
Post by: santiagokq on December 25, 2009, 09:49:16 PM
i still can't get my wireless to work, not even get an ip address... i have a rt2870 chipset [148f:3070] which works perfectly in ubuntu (rt2870sta driver).

the recommended app.bin for this chipset is wireless-mod-0.3-sebmod.zip, according to this guide... but i followed those instructions and didn't get anything.
http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page (http://wiki.wdtv.org/doku.php?id=usb_wireless_dongles_table_page)
http://wdtvforum.com/main/index.php?topic=3695.0 (http://wdtvforum.com/main/index.php?topic=3695.0)


then i switched to wireless-mod-rt.app.bin (v 1.30), following all the suggestions in the smartp thread, but no results either... this is what i've got:

system.txt:
http://pastebin.com/f82ecbdb (http://pastebin.com/f82ecbdb)

dmesg.txt:
http://pastebin.com/f22f0888 (http://pastebin.com/f22f0888)

messages.txt:
http://pastebin.com/f32bc5830 (http://pastebin.com/f32bc5830)


here's my net.config:
http://pastebin.com/f79ae9cae (http://pastebin.com/f79ae9cae)

and my RT2870STA.dat:
http://pastebin.com/f1629f52a (http://pastebin.com/f1629f52a)


PLEASE HELP !!
Title: Re: *experimental* wireless usb support package
Post by: kreller on December 29, 2009, 05:46:46 AM
Hi,
I'm trying to make my WD TV working with a USB wireless adapter, I hope someone would help me.

Specs:
WD Tv with B-rad  1.03.01.WDLXTV.0.5.8.1
Linksys/Cisco Compact Wireless-G USB Adaprer WUSB54GC - Version 3.

I have addewd the wpa_supplicant.conf file and added the strings to the net.config file.

When i hit the Power button and the box starts up, it first says No IP on the boot screen and loads
and look normal.

Did i do anything wrong. When i installed the b-rad firmware i did'nt have the wpa settings or wireless adapter
i bought this yesterday.

Could someone help me? 
Title: Re: *experimental* wireless usb support package
Post by: kebien on January 04, 2010, 08:41:00 PM
As my first post I want to point out a problem I found when  I followed some instructions in this forum.
Not that is someone fault,but our newbie's fault related to the lack of knowledge we have until we start making the wireless devices work.
To the point :

I copied the information from ra73sta.dat exactly as I found it in this thread.
The problem is that it shows

WLAN_LOAD = ra73sta.ko

when the correct setting is

WLAN_LOAD = ra73.ko

I couldn't really understand why my belkin F5D7050 version 31xx wouldn't access my wireless router and get an IP,and all came down to this setting.
I would recommend to those trying to make their wireless devices work,to check in messages text if the correct driver is loading ( mine,as being ra73sra.ko in settings,did go nowhere)

In the other hand,I see I can telnet but cannot FTP into the device,but I believe this is also something I have to read on before asking any question.
Hope this help others struggling to make their devices work.
Title: Re: *experimental* wireless usb support package
Post by: krucifix on January 06, 2010, 04:06:16 AM
Thought this could help someone...
Managed to install wireless on WDTV.
Hardware :
Wireless adapter EDIMAX  EW-7718Un (RT2870)
Router : Linksys wrt160nV2 (draft N)
NAS : Promise ns2300 (2x500Gb RAID0)
Software
Firmware  : 1.02.07-ext3-boot-0.9.2
Wireless : wireless-mod-rt.app.bin-1.31
Other : nfs.app.bin
   webserver.app.bin
Net.config
#
# Network configuration file
#You can override the hostname here:
HOST=wdtv
# if you do not set a hostname,a random one is assigned.
# attempt to set jumbo frames
# MTU=9000
# Your other computers should have same MTU or it will break NFS
#
# Dynamic IP Configuration:
DHCP=yes
#
# Static IP Configuration:  (only if not DHCP)
#DHCP=no
#IP=192.168.5.104
#GW=192.168.5.1
#NM=255.255.255.0
#DNS1=192.168.5.1
#DNS2=205.171.3.65

#
# Optional:  specify time server host:

NTP=pool.ntp.org

#one of rt61sta.dat, rt73sta.dat, RT2400.dat, RT2500STA.dat, RT2570STA.dat, RT2870STA.dat (used by rt3070 as well)
WLAN_CFG=RT2870STA.dat
#one of rt61.ko, rt73.ko, rt2400.ko, rt2500.ko, rt2570.ko, rt2870sta.ko, rt3070sta.ko
WLAN_LOAD=rt2870sta.ko
#need to bring up device?
WLAN_UP=yes
#time to sleep while waiting for wireless association
WLAN_SLEEP=5
net.mount
#
# Example net.mounts file to demonstrate auto-mounting
# of network shares
# Mount a windows file share (must be done by IP address)
xmount //192.168.5.103/video video cifs user=myUsername,pass=MyPass
xmount //192.168.5.103/picture picture cifs user=myUsername,pass= MyPass
xmount //192.168.5.103/music music cifs user=myUsername,pass= MyPass
#  if your "guest" account is disabled, you must supply username and password
# xmount //192.168.0.34/ShareName ShareName cifs user=username,pass=password
# Mount a NFS share
xmount 192.168.5.103:/VOLUME1/VIDEO  nfsvideos nfs
# Notice that we no longer need to modprobe, nor create the directory.
# That is handled for us by xmount.
# Also note that if you store a net.mounts file in /conf/ then it will ALSO
# execute on startup.

RT2870STA.dat
#The word of "Default" must not be removed
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=
ChannelGeography=1
SSID=SSID_WEB
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
PktAggregate=0
WmmCapable=1
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=AES
WPAPSK=MYKEYXXX
DefaultKeyID=1
Key1Type=0
Key1Str=0
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
AutoRoaming=0
RoamThreshold=70
APSDCapable=0
APSDAC=0;0;0;0
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_BADecline=0
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
HT_DisallowTKIP=1
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0
AntDiversity=0
BeaconLostTime=4

First I used T&C method and successfully installed  firmware. Then was lazy to read the posts on forum and bought wireless adapter which was not supported  (wrong chipset)  , took me quite some time to realize that, switched to RTFM method and read compatibility list.
Passed on the adapter to "charity" and bought new one Edimax  EW77189Un.
After few plug/unplug /reboot/reset/Google  procedures managed to guess working configuration.
Had to change in RT2870STA.dat
WirelessMode=9 or WirelessMode=7 to get it working. 
Adatper conected at 56Mps.
Then I  mounted the folders on NS2300 with cifs option.
Movies played perfectly. Then tried to play HD  movie (1080,720) - NO GO.
So since both adapter and router supports N protocol, next step was again plug/unplug /reboot/reset/Google.
First thing I've done is that I've plugged in adapter in WIN 7 box and checked if it is working. It was, but again on 54Mps. Messed around with settings on router/adapter but with no success. Finally learned that speeds over 54Mps (or better say for N protocol to work) with WEP security is NO GO. Has to be WPA2PSK (WPA2 PERSONAL) with AES/TPIK security.  After I've changed the security on router connection speed went up to 270Mps.
Plugged the adapter to WDTV rebooted and yet another NO GO.
Changed from EncrypType=TPIK to EncrypType=AES rebooted and success.
Maybe changing HT_DisallowTKIP=1 to HT_DisallowTKIP=0 would allow connection with TPIK EncrypType but since it's working with AES did not try.
Tried to play HD movies from NS2300 and yet another time NO GO, so ended up googling again.
Found out that cifs mounted volume do not provide enough speed for HD streaming so tried to mount nfs share on NAS. Got various messages (I'm Linux dummy) which basically meant I was unsuccessful in mounting nfs.
Since working with telnet and WDTV is pretty awkward (for me at least) , I've setup virtual ubuntu on my WIN 7 box and tried to mount from there. After losing quite few hours trying (as I've said I'm completely ignorant regarding linux) to mount learned that :
a) big difference with smallcaps - uppercaps, folder name should be exactly written ie :
"xmount 192.168.5.103:/volume1/video  nfsvideos nfs" is NO GO
while xmount "192.168.5.103:/VOLUME1/VIDEO  nfsvideos nfs" works like a charm.
b) NS2300 has to be updated to the latest firmware for NFS to work.
Tried playing HD (1080 & 720) movies and SUCCESS.
 :D :D :D
That's it.
Boris


Title: Re: *experimental* wireless usb support package
Post by: kebien on January 10, 2010, 09:08:10 AM
I had some problems but wanted to share the experience

Using a belkin F5D7050 Version 3125 (RT73)
I get to stream 720p over wireless using samba/CIFS
But is really peculiar
It can play flawless if the shared folders are in hdd  internal (eide,sata) in the server pc,but not so good if the shares are in an USB hard drive connected in that same pc.
Using the USB drive the movie start stuttering after 10 minutes
Using the internal HDD movies play flawless.
Of course those 720p files are not a treat regarding bitrate,but still create problems in certain setups.

Now,I tried to use NFS instead,and no matter what I do or what options I use for xmount (hard,soft,intr,nolock,and so on) the folder shows up EMPTY in the wdtv.
Cannot find what the problem could be,tried many things posted in this same forum.

Also,was anyone able to compile drivers for realtek 8191 ?  (belkin wireless N F5D8083)
Title: Re: *experimental* wireless usb support package
Post by: theklik on January 22, 2010, 11:00:24 AM
I have a wifi dongel with rt2070 chipset
is there a way to use it with the wdtv?

i saw a reply int this thred but i culdnt really undestand what to do and the links in it are dead

thanks
Title: Re: *experimental* wireless usb support package
Post by: cobe on January 26, 2010, 09:48:30 AM
i've noticed that Dlink DWA-160 has in B rev version has also Ralink RT2870 chipset. Is there anybody here that has this model?
Do you think it will work with drivers supported for DWA-140?

thank you!
Title: Re: *experimental* wireless usb support package
Post by: DivDax on January 27, 2010, 11:10:56 AM
Hi!

I bought a WDTV and flashed it with the newest custom firmware WDXTV.
Now i have a D-Link DWA-125 WLAN-Stick but the WDTV has no IP.

How i can install the WLAN-Stick?
Sorry, this is not my thing and my english is bad. :D

Please help!


Thanks!
Div
Title: Re: *experimental* wireless usb support package
Post by: cardean on February 02, 2010, 11:13:16 AM
Has anyone tried this adapter from Hercules (http://www.hercules.com/es/wifi/bdd/p/104/hercules-wireless-n-usb-mini-hwnum-300-/ (http://www.hercules.com/es/wifi/bdd/p/104/hercules-wireless-n-usb-mini-hwnum-300-/)) with the WDHDTV??

I think it's the perfect companion for the WD, as its small size and black color is perfect with the player.

I've read around the forums that there are drivers that support this adapter in Linux, so I think it's possible to make it works with the WD...

Any suggestions will be welcome!

Thanks in advance!
Title: Re: *experimental* wireless usb support package
Post by: grumbler on February 19, 2010, 01:46:35 AM
Manage to get WDLXTV working with D-LINK DWL-G120 and WPA using wireless-mod-rt.app.bin.
Here goes the configuration hoping that it can help someone.

My net.config:
Quote
#You can override the hostname here:
HOST=wdtv
MDEV=rausb0

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#one of rt61sta.dat, rt73sta.dat, RT2400.dat, RT2500STA.dat, RT2570STA.dat, RT2870STA.dat (used by rt3070 as well)
WLAN_CFG=rt73sta.dat
#one of rt61.ko, rt73.ko, rt2400.ko, rt2500.ko, rt2570.ko, rt2870sta.ko, rt3070sta.ko
WLAN_LOAD=rt73.ko
#need to bring up device?
WLAN_UP=no
#time to sleep while waiting for wireless association
WLAN_SLEEP=10

#
# Static IP Configuration:  (only if not DHCP)
DHCP=yes

#
# Optional: 

#specify time server host
NTP=pool.ntp.org

My rt73sta.dat
Quote
[Default]
CountryRegion=2
CountryRegionABand=7
WirelessMode=9
SSID=MYSSID
NetworkType=Infra
Channel=11
#AuthMode=None
AuthMode=WPAPSK
EncrypType=TKIP
#DefaultKeyID=1
#Key1Type=0
#Key1Str=1388557ACF
#Key2Type=0
#Key2Str=
#Key3Type=0
#Key3Str=
#Key4Type=0
#Key4Str=
WPAPSK=MYPASSWORD
TxBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy=0;0;0;0
BGProtection=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0
AdhocOfdm=0
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
CarrierDetect=0

Mind you that it takes some minutes (about 3 or 4) after the WDTV boots to have wireless working. Don't know if anyone else see also this kind of behaviour. I guess that this was the main reason why it took me so long to have this working, I turned off the device too early :).

Regards
Title: Re: *experimental* wireless usb support package
Post by: TechN9Ne1730 on February 19, 2010, 11:37:21 AM
If this has been explained, forgive me, but how do i configure this for my network?
Title: Re: *experimental* wireless usb support package
Post by: votopec on March 03, 2010, 04:49:31 AM
I tried to connect wireless with d-link dwl-g122 (rt73) C1 3.00 firmware version. I installed wdlxtv 5.8.1.
It didn't work, wdtv would halt during the boot without ever coming to menu. For one time it worked, i don't know why because later was gone again.
Act light on stick never blinked.
Then I tried ext3-boot and still no go. It worked without DHCP only and veeery slow. I tried to change all the settings in files. I also tried both wireless app.bin ( Zorander and Smartp ).

I downgraded to 5.3.2. firmware and it started to work. However I would like to use it with 5.8.1.
One thing I realised with 5.8.1. is that when I put encription to WPA2 finnaly I got my usb wireless stick to blink act light. Then in log file I see it connected to wireless but didn't get IP with or without DHCP. With NONE or WEP it gets stuck before. In log it halts at: Dec 31 16:00:55 WDTV-405d0 user.warn kernel: => usb_rtusb_open

If any of you can help I would appreciate that.
Title: Re: *experimental* wireless usb support package
Post by: demesmaeker on March 10, 2010, 02:19:46 PM
I have a wifi dongel with rt2070 chipset
is there a way to use it with the wdtv?

i saw a reply int this thred but i culdnt really undestand what to do and the links in it are dead

thanks


I made a driver that worked for your chipset (for sure if its the linksys wusb54GC version 3):
See more info at http://wdtvforum.com/main/index.php?topic=5123.0 (http://wdtvforum.com/main/index.php?topic=5123.0)
Title: Re: *experimental* wireless usb support package
Post by: kjmurthy on March 13, 2010, 03:00:50 AM
Hi Kebien, I have Belkin Wireless G USB Adapter model number F5D7050. I have WEP security enabled on my wireless network. I have installed WDLXTV till now. I am not able to get a proper help on getting the Wireless working on my WDTV. I saw your post and understand you also have Belkin Wireless G USB Adapter model number F5D7050. It would be of great help if you can give me steps for getting wireless working for me.
Thanks again for the help.
Title: Re: *experimental* wireless usb support package
Post by: kebien on March 13, 2010, 10:36:12 AM
Hi Kebien, I have Belkin Wireless G USB Adapter model number F5D7050. I have WEP security enabled on my wireless network. I have installed WDLXTV till now. I am not able to get a proper help on getting the Wireless working on my WDTV. I saw your post and understand you also have Belkin Wireless G USB Adapter model number F5D7050. It would be of great help if you can give me steps for getting wireless working for me.
Thanks again for the help.

Using this files in root of h usb stick or HDD :

-------------------------
wireless-mod-rt.app
-------------------------
rt73sta.dat

(using this setting)
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=XXXX  ----------->edit to yours
NetworkType=Infra
Channel=0
AuthMode=OPEN  -------------> I would try his frst
EncrypType=NONE  -----------> and this
(the rest is standard)
---------------------------------------------------------------

net.config
(using this settings)
HOST=wdtv
GROUP=XXXX                  ------------>edit to yours
MTU=1492                       ----------------> look in your router for this value if available
insmod /tmp/mnt/sda1/rt73.ko
DHCP=yes
#IP=192.168.0.190
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
ifconfig $MDEV up
WLAN_CFG=rt73sta.dat
WLAN_LOAD=rt73.ko
WLAN_UP=yes
WLAN_SLEEP=1
SUPPRESS_OTHERS=yes
--------------------------------------------

This is my working setup.
You should try first without WEP,make it open,once it works you can heck if WEP works.

Make sure the files have the names correct,linux is picky about it. (for example : rt73sta.dat is not the same as rt73STA.dat )

Hope this help you.

 







Title: Re: *experimental* wireless usb support package
Post by: kjmurthy on March 13, 2010, 03:18:51 PM
Hi ,
Thanks for the reply. I followed the steps:
1. Installed WDLXTV – enhanced WDTV firmware 0.5.8.1 + core-extras.app.bin-0.2 + Optware for WDTV
2. Rebooted the system
3. Disabled Security on my Router
4. Inserted the formatted flash with net.config, wireless-mod-rt.app.bin and and rt61sta.dat making all the changes you mentioned
a. Used http://rt2400.cvs.sourceforge.net/ (http://rt2400.cvs.sourceforge.net/)*checkout*/rt2400/source/rt73/Module/rt73sta.dat
b. I was using channel 3 so i changed channel to 3
c. i used group as WORKGROUP
d. I used MTU as 1500 Which was mentioned in my router
5. i booted WDTV with Belkin Wifi adapter attached to the left of the WDTV USB and the flash driver with the files to the main USB
6. after 1 min i am getting Home screen with NO IP

Please let me know if i missed any steps. I did the same almost 4 times but could not get IP.
Title: Re: *experimental* wireless usb support package
Post by: wongdong on March 13, 2010, 10:10:13 PM
I had a really funny problem and wanted to share how i solved it:

I used a MSI US54SE Wlan stick to connect to my Wifi with WEP only for some time. Worked fine.

Then i switched to WPA2 encryption but i couldn't get it to run, although the net.conf and wpa_supplicant were correct. Out of a hunch i copied (dd'ed) the complete partition from my initially used 256 MB USB stick to a 512 USB stick.
That was it, now it works. Apparently, USB sticks can be to slow some times.

Cheers, WD
Title: Re: *experimental* wireless usb support package
Post by: kebien on March 14, 2010, 08:55:46 AM
Hi ,
Thanks for the reply. I followed the steps:
1. Installed WDLXTV – enhanced WDTV firmware 0.5.8.1 + core-extras.app.bin-0.2 + Optware for WDTV
2. Rebooted the system
3. Disabled Security on my Router
4. Inserted the formatted flash with net.config, wireless-mod-rt.app.bin and and rt61sta.dat making all the changes you mentioned
a. Used http://rt2400.cvs.sourceforge.net/ (http://rt2400.cvs.sourceforge.net/)*checkout*/rt2400/source/rt73/Module/rt73sta.dat
b. I was using channel 3 so i changed channel to 3
c. i used group as WORKGROUP
d. I used MTU as 1500 Which was mentioned in my router
5. i booted WDTV with Belkin Wifi adapter attached to the left of the WDTV USB and the flash driver with the files to the main USB
6. after 1 min i am getting Home screen with NO IP

Please let me know if i missed any steps. I did the same almost 4 times but could not get IP.

Do the same again but installing log-aver.app.bin in root
Then post what messages.txt say here.
Only way to troubleshoot is by looking at logs
Title: Re: *experimental* wireless usb support package
Post by: megatrack67 on March 23, 2010, 05:14:43 PM
does somebody has a wireless config for a DWA-140B2 (07d1:3c0a) ?

thank you for your help


mega
Title: Re: *experimental* wireless usb support package
Post by: kimera on March 25, 2010, 09:17:15 AM
hi guys i'm italian sorry for my english.
i have a problem with the configuration of mi usb stick.

mi hardware config is

WIFI usb stick --> TP-LINK TL-321G (rt73 i suppose)
my net.config is

Quote
# Network configuration file

#You can override the hostname here:

HOST=wdtv
iwconfig >> /boot/log.txt
#
#
ifconfig rausb0 up
#
ifconfig rausb0 up
wpa_supplicant -B -D ralink -i rausb0 -c /boot/wpa_supplicant.conf > /boot/wpa.txt
sleep 5
iwlist rausb0 scanning > /boot/iwlist_scan.txt
ifconfig rausb0 > /boot/configurazione.txt
Sleep 10
# if you do not set a hostname,a random one is assigned.


# attempt to set jumbo frames
# MTU=9000
# Your other computers should have same MTU or it will break NFS


#
# Dynamic IP Configuration:

#DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)

DHCP=no
IP=192.168.1.200
GW=192.168.1.1
NM=255.255.255.0
DNS1=192.168.1.1
DNS2=192.168.1.1

#
# Optional:  specify time server host:

#NTP=pool.ntp.org

my others file is
messages.txt
Quote
Jan  1 00:00:27 wdtv syslog.info syslogd started: BusyBox v1.10.0
Jan  1 00:00:27 wdtv user.notice kernel: klogd started: BusyBox v1.10.0 (2009-02-15 05:09:42 CST)
Jan  1 00:00:27 wdtv user.notice kernel: Linux version 2.6.15-TvDock (william@SVN-server) (gcc version 4.0.4) #11 PREEMPT Wed Dec 24 17:28:32 CST 2008
Jan  1 00:00:27 wdtv user.warn kernel: Configured for SMP863x (revision ES6+/RevA+), detected SMP8635 (revision ES9/RevC).
Jan  1 00:00:27 wdtv user.warn kernel: Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz
Jan  1 00:00:27 wdtv user.info kernel: SMP863x/SMP865x Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe
Jan  1 00:00:27 wdtv user.info kernel:  BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD
Jan  1 00:00:27 wdtv user.warn kernel: Valid MEMCFG found at 0x10000fc0.
Jan  1 00:00:27 wdtv user.warn kernel: CPU revision is: 00019069
Jan  1 00:00:27 wdtv user.warn kernel: Determined physical RAM map:
Jan  1 00:00:27 wdtv user.warn kernel:  memory: 06fe0000 @ 10020000 (usable)
Jan  1 00:00:27 wdtv user.debug kernel: On node 0 totalpages: 94208
Jan  1 00:00:27 wdtv user.debug kernel:   DMA zone: 94208 pages, LIFO batch:31
Jan  1 00:00:27 wdtv user.notice root: Displaying detected USB devices...
Jan  1 00:00:27 wdtv user.debug kernel:   DMA32 zone: 0 pages, LIFO batch:0
Jan  1 00:00:28 wdtv user.notice root:  [148f:2573] 1-1( 2.00,480m) 54M.USB.......
Jan  1 00:00:28 wdtv user.debug kernel:   Normal zone: 0 pages, LIFO batch:0
Jan  1 00:00:28 wdtv user.notice root:  [0471:082b] 1-2( 2.00,480m) USB Flash Drive/AA04012700007588
Jan  1 00:00:29 wdtv user.debug kernel:   HighMem zone: 0 pages, LIFO batch:0
Jan  1 00:00:29 wdtv user.notice root:  [0000:0000] usb1( 2.00,480m) TangoX USB 2.0/tangox-ehci-hcd
Jan  1 00:00:29 wdtv user.warn kernel: Built 1 zonelists
Jan  1 00:00:30 wdtv user.notice root:  [0000:0000] usb2( 1.10,12m) USB Host Controller/TANGOX OHCI
Jan  1 00:00:30 wdtv user.notice kernel: Kernel command line: console=ttyS0
Jan  1 00:00:31 wdtv daemon.info utelnetd[553]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:00:31 wdtv user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Jan  1 00:00:32 wdtv user.notice root: INIT: mounting app binaries...
Jan  1 00:00:32 wdtv user.warn kernel: Primary data cache 16kB, 2-way, linesize 16 bytes.
Jan  1 00:00:33 wdtv user.notice root: Mounting /boot/wireless-mod.app.bin at /apps/wireless-mod
Jan  1 00:00:33 wdtv user.warn kernel: Synthesized TLB refill handler (20 instructions).
Jan  1 00:00:33 wdtv user.warn kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan  1 00:00:34 wdtv user.warn kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan  1 00:00:34 wdtv user.warn kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan  1 00:00:34 wdtv user.warn kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Jan  1 00:00:35 wdtv user.warn kernel: Using 148.500 MHz high precision timer.
Jan  1 00:00:35 wdtv user.warn kernel: Console: colour dummy device 80x25
Jan  1 00:00:35 wdtv user.warn kernel: Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jan  1 00:00:36 wdtv user.warn kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jan  1 00:00:36 wdtv user.notice root: Path set to /apps/wireless-mod/bin:/boot/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:36 wdtv user.info kernel: Memory: 107776k/114560k available (2635k kernel code, 6776k reserved, 392k data, 252k init, 0k highmem)
Jan  1 00:00:38 wdtv user.debug kernel: Calibrating delay loop... 291.84 BogoMIPS (lpj=145920)
Jan  1 00:00:38 wdtv user.warn kernel: Mount-cache hash table entries: 512
Jan  1 00:00:39 wdtv authpriv.info dropbear[660]: Running in background
Jan  1 00:00:39 wdtv user.notice root: vfat: Waiting for 10B0-2075 to mount
Jan  1 00:00:39 wdtv user.warn kernel: Checking for 'wait' instruction...  available.
Jan  1 00:00:40 wdtv user.notice root: Polling detected drives...
Jan  1 00:00:40 wdtv user.info kernel: NET: Registered protocol family 16
Jan  1 00:00:41 wdtv user.warn kernel: tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000.
Jan  1 00:00:41 wdtv user.notice root: Waiting for /dev/sda1 to come online (UUID=10B0-2075)...
Jan  1 00:00:41 wdtv user.warn kernel: PCI: Initializing SMP863x/SMP865x PCI host controller
Jan  1 00:00:42 wdtv user.warn kernel: PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB
Jan  1 00:00:42 wdtv user.warn kernel: PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB
Jan  1 00:00:43 wdtv user.warn kernel: PCI: Configured SMP863x/SMP865x as PCI slave with 128MB PCI memory
Jan  1 00:00:43 wdtv user.warn kernel: PCI: Region size is 16384KB
Jan  1 00:00:43 wdtv user.warn kernel: PCI: Map DMA memory 0x10020000-0x17000000 for PCI at 0x11000000
Jan  1 00:00:44 wdtv user.notice kernel: SCSI subsystem initialized
Jan  1 00:00:44 wdtv user.info kernel: usbcore: registered new driver usbfs
Jan  1 00:00:45 wdtv user.info kernel: usbcore: registered new driver hub
Jan  1 00:00:47 wdtv user.warn kernel: Created /proc/cpucache_info entry.
Jan  1 00:00:47 wdtv user.info kernel: NTFS driver 2.1.25 [Flags: R/O].
Jan  1 00:00:47 wdtv user.warn kernel: fuse init (API version 7.3)
Jan  1 00:00:48 wdtv user.info kernel: Initializing Cryptographic API
Jan  1 00:00:49 wdtv user.info kernel: io scheduler noop registered
Jan  1 00:00:49 wdtv user.info kernel: io scheduler anticipatory registered
Jan  1 00:00:49 wdtv user.info kernel: io scheduler deadline registered
Jan  1 00:00:50 wdtv user.info kernel: io scheduler cfq registered
Jan  1 00:00:50 wdtv user.info kernel: SMP86xx ir (254:0): driver loaded (wait_period = 300ms, buffer_size = 2)
Jan  1 00:00:51 wdtv user.info kernel: SMP86xx led_rst (253:0): driver loaded.
Jan  1 00:00:51 wdtv user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan  1 00:00:51 wdtv user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
Jan  1 00:00:52 wdtv user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
Jan  1 00:00:52 wdtv user.info kernel: loop: loaded (max 8 devices)
Jan  1 00:00:52 wdtv user.notice kernel: physmap flash device CS2: 1000000 at 48000000
Jan  1 00:00:53 wdtv user.info kernel: CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Jan  1 00:00:53 wdtv user.warn kernel:  Amd/Fujitsu Extended Query Table at 0x0040
Jan  1 00:00:54 wdtv user.warn kernel: CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top.
Jan  1 00:00:54 wdtv user.notice kernel: number of CFI chips: 1
Jan  1 00:00:54 wdtv user.notice kernel: cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Jan  1 00:00:55 wdtv user.notice kernel: Using physmap partition definition
Jan  1 00:00:55 wdtv user.notice kernel: Adding partition #1-#5
Jan  1 00:00:55 wdtv user.notice kernel: Creating 5 MTD partitions on "CS2: Physically mapped flash":
Jan  1 00:00:56 wdtv user.notice kernel: 0x00000000-0x00060000 : "CS2-Part1"
Jan  1 00:00:56 wdtv user.notice kernel: 0x00060000-0x00280000 : "CS2-Part2"
Jan  1 00:00:57 wdtv user.notice kernel: 0x00280000-0x00fc0000 : "CS2-Part3"
Jan  1 00:00:57 wdtv user.notice kernel: 0x00fc0000-0x00fe0000 : "CS2-Part4"
Jan  1 00:00:57 wdtv user.notice kernel: 0x00fe0000-0x01000000 : "CS2-Part5"
Jan  1 00:00:58 wdtv user.notice kernel: physmap flash device CS3: 4000000 at 4c000000
Jan  1 00:00:58 wdtv user.debug kernel: CFI: Found no CS3: Physically mapped flash device at location zero
Jan  1 00:00:59 wdtv user.warn kernel: driver tangox-ehci-hcd, 10 Dec 2004
Jan  1 00:00:59 wdtv user.warn kernel: TangoX USB initializing...
Jan  1 00:01:00 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
Jan  1 00:01:01 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
Title: Re: *experimental* wireless usb support package
Post by: kimera on March 25, 2010, 09:20:08 AM
Quote
Jan  1 00:01:01 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021500
Jan  1 00:01:02 wdtv user.info kernel: tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
Jan  1 00:01:02 wdtv user.info kernel: hub 1-0:1.0: USB hub fou
Jan  1 00:01:02 wdtv user.info kernel: nd
Jan  1 00:01:03 wdtv user.info kernel: hub 1-0:1.0: 2 ports detected
Jan  1 00:01:03 wdtv user.warn kernel: TangoX USB was initialized.
Jan  1 00:01:04 wdtv user.warn kernel: Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
Jan  1 00:01:04 wdtv user.notice root: net.agent: Called for rausb0
Jan  1 00:01:04 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
Jan  1 00:01:05 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
Jan  1 00:01:06 wdtv user.info kernel: tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
Jan  1 00:01:07 wdtv user.info kernel: hub 2-0:1.0: USB hub found
Jan  1 00:01:08 wdtv user.info kernel: hub 2-0:1.0: 2 ports detected
Jan  1 00:01:09 wdtv user.info kernel: usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2
Jan  1 00:01:11 wdtv daemon.notice statd[1363]: Version 1.1.5 Starting
Jan  1 00:01:12 wdtv user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:01:12 wdtv daemon.notice statd[1363]: statd running as root. chown /tmp/nfs/sm to choose different user
Jan  1 00:01:13 wdtv user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:01:14 wdtv user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:01:15 wdtv user.debug kernel: usb-storage: device found at 3
Jan  1 00:01:15 wdtv user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:01:15 wdtv user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:01:16 wdtv user.info kernel: USB Mass Storage support registered.
Jan  1 00:01:17 wdtv user.notice root: net.agent: Using /boot/net.config: DHCP=no IP=192.168.1.200 GW=192.168.1.1
Jan  1 00:01:17 wdtv user.info kernel: NET: Registered protocol family 2
Jan  1 00:01:18 wdtv user.notice root: Testing static IP assignment...
Jan  1 00:01:19 wdtv user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:01:19 wdtv user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:01:20 wdtv user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:01:20 wdtv user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:01:21 wdtv user.info kernel: TCP reno registered
Jan  1 00:01:21 wdtv user.info kernel: TCP bic registered
Jan  1 00:01:21 wdtv user.info kernel: NET: Registered protocol family 1
Jan  1 00:01:22 wdtv user.info kernel: NET: Registered protocol family 17
Jan  1 00:01:22 wdtv user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:01:23 wdtv user.notice kernel:   Vendor: Philips   Model: USB Flash Drive   Rev: 1100
Jan  1 00:01:23 wdtv user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:01:24 wdtv user.notice kernel: SCSI device sda: 1981440 512-byte hdwr sectors (1014 MB)
Jan  1 00:01:24 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:01:24 wdtv user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:01:25 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:01:25 wdtv user.notice kernel: SCSI device sda: 1981440 512-byte hdwr sectors (1014 MB)
Jan  1 00:01:26 wdtv user.notice kernel: sda: Write Protect is off
Jan  1 00:01:29 wdtv user.notice root: xmounter: entering stage2
Jan  1 00:01:29 wdtv user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:01:30 wdtv user.notice root: Now mounted:
Jan  1 00:01:30 wdtv user.err kernel: sda: assuming drive cache: write through
Jan  1 00:01:30 wdtv user.notice root: rootfs on / type rootfs (rw)
Jan  1 00:01:31 wdtv user.info kernel:  sda: sda1
Jan  1 00:01:31 wdtv user.notice root: proc on /proc type proc (rw,nodiratime)
Jan  1 00:01:31 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:01:32 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:32 wdtv user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:01:32 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:33 wdtv user.debug kernel: usb-storage: device scan complete
Jan  1 00:01:33 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:34 wdtv user.info kernel: kjournald starting.  Commit interval 5 seconds
Jan  1 00:01:34 wdtv user.notice root: /dev/sda1 on /boot type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:34 wdtv user.notice root: Ping: 6 packets transmitted, 0 packets received, 100% packet loss
Jan  1 00:01:34 wdtv user.warn kernel: EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
Jan  1 00:01:35 wdtv user.notice root: /dev/loop1 on / type ext3 (rw,noatime,nodiratime,data=ordered)
Jan  1 00:01:35 wdtv user.notice root: IP Assignment failed. Trying DHCP
Jan  1 00:01:36 wdtv user.info kernel: EXT3 FS on loop1, internal journal
Jan  1 00:01:36 wdtv user.notice root: none on /proc type proc (rw,nodiratime)
Jan  1 00:01:37 wdtv user.info kernel: EXT3-fs: recovery complete.
Jan  1 00:01:38 wdtv user.notice root: usb on /proc/bus/usb type usbfs (rw)
Jan  1 00:01:38 wdtv user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Jan  1 00:01:38 wdtv user.notice root: sysfs on /sys type sysfs (rw)
Jan  1 00:01:39 wdtv user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:01:39 wdtv user.notice root: mdev on /dev type tmpfs (rw)
Jan  1 00:01:39 wdtv user.warn kernel: em8xxx: no version for "llad_open" found: kernel tainted.
Jan  1 00:01:40 wdtv user.notice root: devpts on /dev/pts type devpts (rw)
Jan  1 00:01:40 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:01:40 wdtv user.notice root: none on /tmp type tmpfs (rw)
Jan  1 00:01:41 wdtv user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:01:41 wdtv user.notice root: none on /apps type tmpfs (rw)
Jan  1 00:01:41 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:01:41 wdtv user.notice root: /dev/loop0 on /apps/wireless-mod type cramfs (ro)
Jan  1 00:01:42 wdtv user.warn kernel: mumk_register_tasklet: (0) tasklet c401e000 status @c938aa24
Jan  1 00:01:42 wdtv user.notice root: /dev/sda1 on /tmp/media/usb/USB2/10B0-2075 type vfat (rw,sync,noatime,nodiratime,fmask=0022,dmask=0022,codepage=cp437,iocharset=iso8859-1)
Jan  1 00:01:42 wdtv user.warn kernel: em8xxx [/home/andy/WDTV/house_1_02_07/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:01:43 wdtv user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:43 wdtv user.info kernel: Loading wireless extentions module...
Jan  1 00:01:44 wdtv user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:44 wdtv user.warn kernel: mii: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:44 wdtv user.warn kernel: usbnet: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:45 wdtv user.info kernel: usbcore: registered new driver asix
Jan  1 00:01:45 wdtv user.info kernel: /home/Zehd/wdtv/dm9601/dm9601.c: /home/Zehd/wdtv/dm9601/dm9601.c: v0.0.6 2001/05/24 (C) 1999-2000 Petko Manolov (petkan@dce.bg)
Jan  1 00:01:45 wdtv user.info kernel: usbcore: registered new driver dm9601
Jan  1 00:01:46 wdtv user.info kernel: usbcore: registered new driver kaweth
Jan  1 00:01:46 wdtv user.info kernel: usbcore: registered new driver MOSCHIP usb-ethernet driver
Jan  1 00:01:46 wdtv user.info kernel: pegasus: v0.6.12 (2005/01/13), Pegasus/Pegasus II USB Ethernet driver
Jan  1 00:01:47 wdtv user.info kernel: usbcore: registered new driver pegasus
Jan  1 00:01:47 wdtv user.info kernel: usbcore: registered new driver catc
Jan  1 00:01:47 wdtv user.info kernel: drivers/usb/net/catc.c: v2.8 CATC EL1210A NetMate USB Ethernet driver
Jan  1 00:01:48 wdtv user.info kernel: drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
Jan  1 00:01:48 wdtv user.info kernel: usbcore: registered new driver rtl8150
Jan  1 00:01:48 wdtv user.warn kernel: cdc_ether: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:49 wdtv user.info kernel: usbcore: registered ne
Jan  1 00:01:49 wdtv user.info kernel: w driver cdc_ether
Jan  1 00:01:49 wdtv user.info kernel: usbcore: registered new driver cdc_subset
Jan  1 00:01:49 wdtv user.info kernel: usbcore: registered new driver net1080
Jan  1 00:01:50 wdtv user.info kernel: usbcore: registered new driver plusb
Jan  1 00:01:50 wdtv user.info kernel: usbcore: registered new driver rndis_host
Jan  1 00:01:51 wdtv user.info kernel: usbcore: registered new driver gl620a
Jan  1 00:01:51 wdtv user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:01:51 wdtv user.info kernel: usbcore: registered new driver zd1201
Jan  1 00:01:52 wdtv user.notice kernel: ZD1211B - version 2.19.2.9
Jan  1 00:01:52 wdtv user.info kernel: usbcore: registered new driver zd1211b
Jan  1 00:01:52 wdtv user.notice kernel: arusb - version 0.0.0.999
Jan  1 00:01:53 wdtv user.info kernel: usbcore: registered new driver Otus
Jan  1 00:01:53 wdtv user.warn kernel: rtusb init --->
Jan  1 00:01:53 wdtv user.info kernel: usbcore: registered new driver rt2870
Jan  1 00:01:53 wdtv user.warn kernel: idVendor = 0x148f, idProduct = 0x2573
Jan  1 00:01:54 wdtv user.info kernel: usbcore: registered new driver rt73
Jan  1 00:01:54 wdtv user.debug kernel: rausb0 (WE) : Driver using old /proc/net/wireless support, please fix driver !
Jan  1 00:01:54 wdtv user.warn kernel: => usb_rtusb_open
Jan  1 00:01:55 wdtv user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:55 wdtv user.debug kernel: ir: Enable RC5 decoder (0x00000000)
and wpa_supplicant with wpa.txt
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Taverna"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
psk="mypass"
}

wpa.txt
Quote
Line 1: Invalid configuration line '{\rtf1\ansi\ansicpg1252\cocoartf1038\cocoasubrtf250'.
Line 2: Invalid configuration line '{\fonttbl\f0\froman\fcharset0 Times-Roman;}'.
Line 3: Invalid configuration line '{\colortbl;\red255\green255\blue255;}'.
Line 4: Invalid configuration line '\paperw11900\paperh16840\margl1440\margr1440\vieww9000\viewh8400\viewkind0'.
Line 5: Invalid configuration line '\deftab720'.
Line 6: Invalid configuration line '\pard\pardeftab720\ql\qnatural'.
Line 8: Invalid configuration line '\f0\fs24 \cf0 ctrl_interface=/tmp/wpa_supplicant\'.
Line 9: Invalid configuration line 'network=\{\'.
Line 10: Invalid configuration line 'ssid="Taverna"\'.
Line 13: Invalid configuration line 'key_mgmt=WPA-PSK\'.
Line 14: Invalid configuration line 'psk="mypass"\'.
Line 15: Invalid configuration line '\}}'.
Failed to read or parse configuration '/boot/wpa_supplicant.conf'.
Title: Re: *experimental* wireless usb support package
Post by: thomasyuan on April 08, 2010, 04:05:52 PM
does somebody has a wireless config for a DWA-140B2 (07d1:3c0a) ?

thank you for your help


mega

yeah, from here:
http://wdtvforum.com/main/index.php?topic=2359.0 (http://wdtvforum.com/main/index.php?topic=2359.0)
Title: Re: *experimental* wireless usb support package
Post by: rob_z11 on May 04, 2010, 08:48:28 AM
I was wondering if there is any plan to support this Linksys USB Wireless card?

1737  Linksys
   0078  WUSB100 RangePlus Wireless USB Network Adapter ver. 2
   
Title: Re: *experimental* wireless usb support package
Post by: pkin on May 06, 2010, 08:53:35 PM
Hi, I'm sorry I'm totally new to this, started testing today.
After many many many tries I finally got my wireless usb stick flash instead of a constant blue light! yay \o/ but I can't figure how to make it actually work.

I have an Airlink 101 AWLL3026 - Zydas 1211/1211b

here is my wpa_supplicant.conf
Quote
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="****"
# uncomment next line if your ap doesn't broadcast ssid
#scan_ssid=1
key_mgmt=WPA-PSK
proto=WPA2
psk="****"
}

and my net.conf
Quote
#
# Network configuration file

#You can override the hostname here:
HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
MTU=9000

#
# Dynamic IP Configuration:
DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)
#DHCP=no
#IP=192.168.0.10
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=192.168.0.1
#DNS2=205.171.3.65

#
# Optional: 

#specify time server host
#NTP=pool.ntp.org

#specify timezone (example=pacific North America)
#TZ=PST8PDT

#do not load any network drivers (saves memory)
#SUPPRESS_OTHERS=yes

ifconfig $MDEV up
wpa_supplicant -Bw -Dwext -i$MDEV -c/boot/wpa_supplicant.conf

Any help is appreciated Much thanks.

Well after long hours trying turns out I can only connect using WPE.
Title: Re: *experimental* wireless usb support package
Post by: realtebo on May 08, 2010, 09:18:21 AM
I have a DWL-G122

i've downloaded thw wireless-mod.app.bin of 28 of march, 2009. is it the latest?

Then i created this wpa_supplicant.conf

Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
 ssid="Home"
 # uncomment next line if your ap doesn't broadcast ssid
 scan_ssid=1
 proto=WPA2
 key_mgmt=WPA-PSK
 pairwise=CCMP
 group=CCMP
 psk="123456789012345678901234"
}

i have a d-link router with WPA+WPA2 security, using a 24char (numeric) password

my actual net.config file is this

Code: [Select]
#
# Network configuration file

ifconfig $MDEV up
wpa_supplicant -B -D ralink -i $MDEV -c/boot/wpa_supplicant.conf


#You can override the hostname here:
HOST=wdtv

# if you do not set a hostname,a random one is assigned.

# attempt to set jumbo frames
#MTU=9000

#
# Dynamic IP Configuration:
DHCP=yes

#
# Static IP Configuration:  (only if not DHCP)
#DHCP=no
#IP=192.168.0.30
#GW=192.168.0.1
#NM=255.255.255.0
#DNS1=81.29.230.1
#DNS2=81.29.230.5

#
# Optional: 

#specify time server host
NTP=pool.ntp.org

#specify timezone (example=pacific North America)
TZ=CET

#do not load any network drivers (saves memory)
#SUPPRESS_OTHERS=yes

my wifi Adapter is plugged into rear usb, with a fully compatible usbx4 adapter serving a verbatim usb disk

When I reboot my wdtv
it show the background image where it could be the ip, but nothing written over it.  Freezed i suppose

How to debug?

ABOUT 1 year ago, this pen with this disk with this adapter was working right, so i'm sure that adapter is working with wdtv

my wdtv firmware is wdlxtv latest available.

Title: Re: *experimental* wireless usb support package
Post by: kimw on May 18, 2010, 02:34:46 AM

Sorry but I am new to this whole thing and I need some explanation:

When I installed this wireless usb mod correctly, will I have any kind of GUI interface implemented in the main GUI...so I can for example choose "Video -> Network shares" like on the WDTV HD Live? Or how do I get access to some streaming media over wifi?

second question: if I buy a compatible usb wifi usb dongle, could anyone from this forum write me a working script if I tell them all my wifi WPA, PASSWORT, IP, etc data that is needed? I read all the tutorials and it seems I do not understand anything at all... I have no clue about linux programming also  :(

thank you guys in advance.

cheers from Germany.



Title: Re: *experimental* wireless usb support package
Post by: abdou74 on August 30, 2010, 05:23:55 PM
need help
hello

I have a first generation WDTV, a key dwa120 Fi D-Link (Atheros ar5523 chipset) and a router thomson speedtouch 706 wl
I try everything to run the wifi May nothing works

I took it to you to help me, give me a fair procedur step by step because I am a novice

thank you in advance
Title: Re: *experimental* wireless usb support package
Post by: givitup2E on September 09, 2010, 07:01:08 PM
To set up the wdtv to work with an usb wireless card appears alot of work. Especially for one myself who alot of the info I read on how to set it up is out of my element. My question before I try and jump in and make it work, is am I able to network the drives that are attached to my wdtv? All I wish to be able to do is send files to them, edit them and delete them when needed. Can this be accomplished? Everything I read seems people's goal to network the wdtv is to stream video from a computer where the drives would be located. Thank you for any insight.
Title: Re: *experimental* wireless usb support package
Post by: wandrey on September 17, 2010, 09:48:39 PM
I need help, i want a compiled driver for wdtv, for RTL8192U. Any body can help me? please? TKs
Title: Re: *experimental* wireless usb support package
Post by: Pine on November 05, 2010, 07:56:28 PM
Hi, All,

Anyone can tell me does this package (Ver 0.1 ~ 0.3) really support Atheros Otus?


Bus 001 Device 005: ID 0cf3:9170 Atheros Communications, Inc.

Here is my config:

...
ifconfig $MDEV up
wpa_supplicant -Bw -Dotus -i$MDEV -c/tmp/mnt/wpa_supplicant.conf
...

Thx
Title: Dead thread?
Post by: xwishmasterx on November 14, 2010, 02:19:48 AM
Does anyone offer any help on this topic anymore? It seems like no one has gotten replies for weeks. I also need some help getting this setup but will try somewhere else if nobody is willing to offer any help in this forum.
Title: Re: *experimental* wireless usb support package
Post by: calin1975 on December 25, 2010, 06:24:02 AM
Hi, is there any chance for Dlink DWA-160 rev. A2 (pid-vid : 07d1-3a09, Atheros Otus) to be included in the next wireless.mod.app for WDTV Gen1?
According to this post http://forum.wdlxtv.com/viewtopic.php?f=34&t=2361, soon it will be supported in b-rad's 0.4.5.0 version for WDTV Gen2.
DWA-160 A2 and TP-Link TL-WN821N seems to have the same chipset.
Thank you.
Title: Re: *experimental* wireless usb support package
Post by: Tedturbo on January 04, 2011, 09:55:40 AM
 ???  I'm totally confused on setting up wifi on version 1 (not Live).  Here's where I am. From the About Screen I have:
Firmware Version 1.03.01.WDLXTV-0.581
WDTV-229a31: No IP

My Jump Drive contains:
dmesg.txt
event-osd.app
log-saver.app
Msheet.app.conf
Msheet.app.event
system.txt
wireless-mod.app
wireless-mod-wdlxtv.app

I have the following wireless USB Adapters available:
Linksys RangePlus WUSB100
WiBee-N
Azio AWU354

I've booted with each adapter and no IP address gets assigned.  I must be missing something basic here.  I'm wirelessly trying to get to my networks 500G Buffalo Linkstation that is loaded with movies.

Any direction from here would be great!!!

 ??? :'( :o

Ted
Title: Re: *experimental* wireless usb support package
Post by: kebien on January 10, 2011, 05:58:46 AM
Hi, is there any chance for Dlink DWA-160 rev. A2 (pid-vid : 07d1-3a09, Atheros Otus) to be included in the next wireless.mod.app for WDTV Gen1?
According to this post http://forum.wdlxtv.com/viewtopic.php?f=34&t=2361, soon it will be supported in b-rad's 0.4.5.0 version for WDTV Gen2.
DWA-160 A2 and TP-Link TL-WN821N seems to have the same chipset.
Thank you.

I do not think there will ever be any more improvements for wdtv gen1,since is already announced it's been discontinued.

If you want to add more id's into the apps,you'd need to do it yourself,intructions are clear enough for everyone to follow.
Title: Re: *experimental* wireless usb support package
Post by: lala77 on April 02, 2011, 07:19:45 AM
I am trying to connect Airlink 101 wifi-N adapter on wdtv-1gen.
I think I am really close to the final stage but I could not get wpa work.
Any advice is welcome.
Thanks.

net.config
Code: [Select]
#replace CHANGEME with the name of your flash drive
#that would be what you labeled it.
FLASH="/tmp/media/usb/SKYDRVx2"
SSID="NETGEAR777"
wifidev="wlan0"


# if you do not set a hostname,a random one is assigned.
#You can override the hostname here:
HOST=wdtv
# attempt to set jumbo frames
#MTU=9000
#this is for an open wireless setup
#WIFITOOL=IWTOOLS
#uncomment this if you need WPA or WPA2 etc..
#when using this, you MUST configure wpa_supplicant
WIFITOOL=WPASUP

#wireless
if [ ! -f /tmp/running_net.config ]; then
logger "Starting IW Tools.."
touch /tmp/running_net.config

#your driver goes here
#uncomment the correct one
modprobe -v 8712u
#modprobe -v 8192cu
#modprobe -v r8187l

ifconfig ${wifidev} up

case ${WIFITOOL} in

IWTOOLS)
sleep 5
echo ${wifidev}
iwconfig ${wifidev} mode Managed 2>> ${FLASH}/iwifi

iwconfig ${wifidev} essid ${SSID}

;;

WPASUP)

if [ -x ${FLASH}/wpa_supplicant.conf ]; then
if [ ! -x /tmp/wpa_supplicant.ctrl ]; then
logger "IWIFI: WPASUP"
modprobe -v ieee80211_crypt_tkip
modprobe -v ieee80211_crypt_ccmp
modprobe -v ieee80211_crypt_wep
iwlist ${wifidev} scanning > ${FLASH}/iwlist_scan.txt
wpa_supplicant -Bw -Dwext -i${wifidev} -c ${FLASH}/wpa_supplicant.conf
fi
fi

;;

esac

logger "Finished IW Tools.."
else
logger "net.config called again.."
fi

#
# Static IP Configuration: (only if not DHCP)
DHCP=no
IP=192.168.123.150
GW=192.168.123.254
NM=255.255.255.0
DNS1=68.87.64.150
DNS2=68.87.75.198

SUPPRESS_OTHERS=yes

wpa_supplicant.conf
Code: [Select]
ctrl_interface=/tmp/wpa_supplicant
network={
ssid="NETGEAR777"
#scan_ssid=1
key_mgmt=WPA-PSK
psk="blablabla"
}

iwlist_scan.txt
Code: [Select]
wlan0     Scan completed :
          Cell 03 - Address: 30:46:9A:51:1D:78
                    ESSID:"NETGEAR777"
                    Protocol:IEEE 802.11bgn
                    Mode:Master
                    Frequency:2.422 GHz (Channel 3)
                    Encryption key:on
                    Bit Rates:300 Mb/s
                    Extra:wpa_ie=dd1c0050f20101000050f20202000050f2040050f20201000050f2020c00
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : CCMP TKIP
                        Authentication Suites (1) : PSK  
                    Extra:rsn_ie=30180100000fac020200000fac04000fac020100000fac020c00
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : CCMP TKIP
                        Authentication Suites (1) : PSK  
                    IE: WPA Version 18960
                        Group Cipher : Proprietary
                        Pairwise Ciphers (68) :                    
                        Signal level=100/100  

messages.txt
Code: [Select]
--------head cut off due to character limit---------------
Jan  1 00:00:17 WDTV-d72af user.info kernel: Initializing USB Mass Storage driver...
Jan  1 00:00:17 WDTV-d72af user.info kernel: usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3
Jan  1 00:00:17 WDTV-d72af user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan  1 00:00:17 WDTV-d72af user.debug kernel: usb-storage: device found at 2
Jan  1 00:00:17 WDTV-d72af user.debug kernel: usb-storage: waiting for device to settle before scanning
Jan  1 00:00:17 WDTV-d72af user.info kernel: usbcore: registered new driver usb-storage
Jan  1 00:00:17 WDTV-d72af user.info kernel: USB Mass Storage support registered.
Jan  1 00:00:17 WDTV-d72af user.info kernel: NET: Registered protocol family 2
Jan  1 00:00:17 WDTV-d72af user.warn kernel: IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 00:00:17 WDTV-d72af user.warn kernel: TCP established hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:17 WDTV-d72af user.warn kernel: TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
Jan  1 00:00:17 WDTV-d72af user.info kernel: TCP: Hash tables configured (established 16384 bind 16384)
Jan  1 00:00:17 WDTV-d72af user.info kernel: TCP reno registered
Jan  1 00:00:18 WDTV-d72af user.info kernel: TCP bic registered
Jan  1 00:00:18 WDTV-d72af user.info kernel: NET: Registered protocol family 1
Jan  1 00:00:18 WDTV-d72af user.info kernel: NET: Registered protocol family 17
Jan  1 00:00:18 WDTV-d72af user.info kernel: Freeing unused kernel memory: 252k freed
Jan  1 00:00:18 WDTV-d72af user.notice kernel:   Vendor: SKYDRVx2  Model: LOCKPORT(D)       Rev: 1100
Jan  1 00:00:18 WDTV-d72af user.notice kernel:   Type:   Direct-Access                      ANSI SCSI revision: 00
Jan  1 00:00:18 WDTV-d72af user.notice kernel: SCSI device sda: 15663104 512-byte hdwr sectors (8020 MB)
Jan  1 00:00:18 WDTV-d72af user.notice crazyboot: /dev/mtdblock2: LABEL="PRIMARY_SYSTEM" TYPE="romfs"
Jan  1 00:00:18 WDTV-d72af user.notice crazyboot: /dev/mtdblock3: LABEL="WDLXTV-0.5.8.1" TYPE="cramfs"
Jan  1 00:00:18 WDTV-d72af user.notice crazyboot: /dev/sda1: UUID="3040C14F40C11D0A" LABEL="SKYDRVx2" TYPE="ntfs"
Jan  1 00:00:19 WDTV-d72af user.notice kernel: sda: Write Protect is off
Jan  1 00:00:19 WDTV-d72af user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:00:19 WDTV-d72af user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:19 WDTV-d72af user.notice kernel: SCSI device sda: 15663104 512-byte hdwr sectors (8020 MB)
Jan  1 00:00:19 WDTV-d72af user.notice kernel: sda: Write Protect is off
Jan  1 00:00:19 WDTV-d72af user.debug kernel: sda: Mode Sense: 43 00 00 00
Jan  1 00:00:19 WDTV-d72af user.err kernel: sda: assuming drive cache: write through
Jan  1 00:00:19 WDTV-d72af user.info kernel:  sda: sda1
Jan  1 00:00:19 WDTV-d72af user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Jan  1 00:00:19 WDTV-d72af user.notice kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Jan  1 00:00:19 WDTV-d72af user.debug kernel: usb-storage: device scan complete
Jan  1 00:00:19 WDTV-d72af user.warn kernel: cdrom: no version for "struct_module" found: kernel tainted.
Jan  1 00:00:19 WDTV-d72af user.warn kernel: cdrom: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:19 WDTV-d72af user.warn kernel: llad: module license 'LGPL' taints kernel.
Jan  1 00:00:19 WDTV-d72af user.warn kernel: em8xxx [/home/andy/WDTV/house_1.03.01/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1463] init_module: begun
Jan  1 00:00:19 WDTV-d72af user.warn kernel: em8xxx0 [/home/andy/WDTV/house_1.03.01/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1346] identify: board as unknown subid
Jan  1 00:00:19 WDTV-d72af user.warn kernel: em8xxx [/home/andy/WDTV/house_1.03.01/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1449] identify: device 0x8635 0x86 accepted with software tango2revC
Jan  1 00:00:19 WDTV-d72af user.warn kernel: mumk_register_tasklet: (0) tasklet c403f000 status @c938aa24
Jan  1 00:00:19 WDTV-d72af user.warn kernel: em8xxx [/home/andy/WDTV/house_1.03.01/src/libs/2.8.3.0/mrua_SMP8634_2.8.3.0_GCC4_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1581] init_module: done. Found 1 em8xxx
Jan  1 00:00:19 WDTV-d72af user.warn kernel: loop: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:19 WDTV-d72af user.info kernel: loop: loaded (max 24 devices)
Jan  1 00:00:21 WDTV-d72af daemon.notice ntfs-3g[446]: Version 2009.4.4 integrated FUSE 27
Jan  1 00:00:21 WDTV-d72af daemon.notice ntfs-3g[446]: Mounted /dev/sda1 (Read-Write, label "SKYDRVx2", NTFS 3.1)
Jan  1 00:00:21 WDTV-d72af daemon.notice ntfs-3g[446]: Cmdline options:
Jan  1 00:00:21 WDTV-d72af daemon.notice ntfs-3g[446]: Mount options: silent,allow_other,nonempty,relatime,fsname=/dev/sda1
Jan  1 00:00:21 WDTV-d72af user.notice xmount: xmounted /dev/sda1
Jan  1 00:00:21 WDTV-d72af user.notice crazyboot: mounting app binaries...
Jan  1 00:00:22 WDTV-d72af user.warn xmount: partition with label (SKYDRVx2) already mounted!
Jan  1 00:00:23 WDTV-d72af user.notice crazyboot: checking DEVICE /dev/sda1 for app.bins
Jan  1 00:00:23 WDTV-d72af user.notice crazyboot: log-saver app found
Jan  1 00:00:28 WDTV-d72af user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:28 WDTV-d72af daemon.notice ntfs-3g[517]: Version 2009.4.4 integrated FUSE 27
Jan  1 00:00:28 WDTV-d72af daemon.notice ntfs-3g[517]: Mounted /dev/sda1 (Read-Write, label "SKYDRVx2", NTFS 3.1)
Jan  1 00:00:28 WDTV-d72af daemon.notice ntfs-3g[517]: Cmdline options:
Jan  1 00:00:28 WDTV-d72af daemon.notice ntfs-3g[517]: Mount options: silent,allow_other,nonempty,relatime,fsname=/dev/sda1
Jan  1 00:00:28 WDTV-d72af user.notice crazyboot: Mounting log-saver.app.bin at /apps/log-saver
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=68, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=12, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=1252, limit=8
Jan  1 00:00:28 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:28 WDTV-d72af user.info kernel: loop0: rw=0, want=1028, limit=8
Jan  1 00:00:28 WDTV-d72af user.warn kernel: UDF-fs: No partition found (1)
Jan  1 00:00:29 WDTV-d72af user.notice crazyboot: realtek-wireless-drivers-0.1 app found
Jan  1 00:00:29 WDTV-d72af user.notice crazyboot: Mounting realtek-wireless-drivers-0.1.app.bin at /apps/realtek-wireless-drivers-0.1
Jan  1 00:00:29 WDTV-d72af user.info kernel: attempt to access beyond end of device
Jan  1 00:00:29 WDTV-d72af user.info kernel: loop1: rw=0, want=1116, limit=1112
Jan  1 00:00:29 WDTV-d72af user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:29 WDTV-d72af user.notice crazyboot: wireless-mod-wdlxtv app found
Jan  1 00:00:29 WDTV-d72af user.notice crazyboot: Mounting wireless-mod-wdlxtv.app.bin at /apps/wireless-mod-wdlxtv
Jan  1 00:00:29 WDTV-d72af user.warn kernel: UDF-fs: No VRS found
Jan  1 00:00:29 WDTV-d72af user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 00:00:30 WDTV-d72af user.notice crazyboot: extension[s] found on /dev/sda1 - do not remove device from wdtv
Jan  1 00:00:30 WDTV-d72af user.notice crazyboot: adjusting LIBPATH
Jan  1 00:00:33 WDTV-d72af user.notice root: adjusting PATH
Jan  1 00:00:33 WDTV-d72af user.notice crazyboot: Path set to /apps/wireless-mod-wdlxtv/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
Jan  1 00:00:34 WDTV-d72af user.notice mount.watch: starting
Jan  1 00:00:38 WDTV-d72af user.notice root: Starting IW Tools..
Jan  1 00:00:38 WDTV-d72af user.warn kernel: wireless_ext: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:38 WDTV-d72af user.info kernel: Loading wireless extentions module...
Jan  1 00:00:41 WDTV-d72af user.warn kernel: ==DriverVersion: v2.6.6.0.20101111==
Jan  1 00:00:41 WDTV-d72af user.warn kernel:
Jan  1 00:00:41 WDTV-d72af user.warn kernel: 8712_usb_endpoint_descriptor(0):
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bLength=7
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bDescriptorType=5
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bEndpointAddress=83
Jan  1 00:00:41 WDTV-d72af user.warn kernel: wMaxPacketSize=200
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bInterval=0
Jan  1 00:00:41 WDTV-d72af user.warn kernel:
Jan  1 00:00:41 WDTV-d72af user.warn kernel: 8712_usb_endpoint_descriptor(1):
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bLength=7
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bDescriptorType=5
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bEndpointAddress=4
Jan  1 00:00:41 WDTV-d72af user.warn kernel: wMaxPacketSize=200
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bInterval=0
Jan  1 00:00:41 WDTV-d72af user.warn kernel:
Jan  1 00:00:41 WDTV-d72af user.warn kernel: 8712_usb_endpoint_descriptor(2):
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bLength=7
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bDescriptorType=5
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bEndpointAddress=6
Jan  1 00:00:41 WDTV-d72af user.warn kernel: wMaxPacketSize=200
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bInterval=0
Jan  1 00:00:41 WDTV-d72af user.warn kernel:
Jan  1 00:00:41 WDTV-d72af user.warn kernel: 8712_usb_endpoint_descriptor(3):
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bLength=7
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bDescriptorType=5
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bEndpointAddress=d
Jan  1 00:00:41 WDTV-d72af user.warn kernel: wMaxPacketSize=200
Jan  1 00:00:41 WDTV-d72af user.warn kernel: bInterval=0
Jan  1 00:00:41 WDTV-d72af user.warn kernel:
Jan  1 00:00:41 WDTV-d72af user.warn kernel: 8712u : USB_SPEED_HIGH
Jan  1 00:00:41 WDTV-d72af user.warn kernel: nr_endpoint=4
Jan  1 00:00:41 WDTV-d72af user.warn kernel: Boot from EFUSE
Jan  1 00:00:41 WDTV-d72af user.warn kernel: Autoload OK!!
Jan  1 00:00:42 WDTV-d72af user.warn kernel: CustomerID = 0x   0
Jan  1 00:00:42 WDTV-d72af user.warn kernel: MAC Address from efuse= 0-21-2f-36-5b-e
Jan  1 00:00:42 WDTV-d72af user.info kernel: usbcore: registered new driver r871x_usb_drv
Jan  1 00:00:46 WDTV-d72af user.warn kernel: 1 RCR=0x153f00e
Jan  1 00:00:46 WDTV-d72af user.warn kernel: 2 RCR=0x553f00e
Jan  1 00:00:46 WDTV-d72af user.warn kernel: MAC Address= 0-21-2f-36-5b-e
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:RTL8712 FW version 0.0.1# 訝?8??11 20:37:05 CST 2010  SVN
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:Chip Version:00000002
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:HCI type: 00000012(00000004)
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:rf_cofig: 00000011(000000ff, 00000000, 00000000)
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:mp_mode: 00000000(00000001), IQK: 403e00fc
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:vcs type: 00000002(00000001)
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:32k calibra: 790, 32K TSF: 00000029
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:target thermal: 00000012,  bt_coexist: 00000000
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:46 WDTV-d72af user.warn kernel: fwdbg:->(00000001, 00000001, 00000001, 00000000)
Jan  1 00:00:46 WDTV-d72af user.warn kernel:
Jan  1 00:00:49 WDTV-d72af user.notice root: IWIFI: WPASUP
Jan  1 00:00:49 WDTV-d72af user.warn kernel: ieee80211_crypt: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:49 WDTV-d72af user.debug kernel: ieee80211_crypt: registered algorithm 'NULL'
Jan  1 00:00:49 WDTV-d72af user.debug kernel: ieee80211_crypt: registered algorithm 'TKIP'
Jan  1 00:00:49 WDTV-d72af user.debug kernel: ieee80211_crypt: registered algorithm 'CCMP'
Jan  1 00:00:49 WDTV-d72af user.debug kernel: ieee80211_crypt: registered algorithm 'WEP'
Jan  1 00:00:49 WDTV-d72af user.warn kernel: fwdbg:get survey cmd
Jan  1 00:00:49 WDTV-d72af user.warn kernel:
Jan  1 00:00:50 WDTV-d72af user.warn kernel: fwdbg:survey done(00000008, 00000000)
Jan  1 00:00:50 WDTV-d72af user.warn kernel:
Jan  1 00:00:51 WDTV-d72af user.notice root: Finished IW Tools..
Jan  1 00:00:52 WDTV-d72af user.warn kernel: firmware_class: No versions for exported symbols. Tainting kernel.
Jan  1 00:00:53 WDTV-d72af user.notice root: net.config called again..
Jan  1 00:00:59 WDTV-d72af daemon.info utelnetd[1633]: utelnetd (port: 23, ifname: any, login: /bin/login) startup succeeded
Jan  1 00:01:01 WDTV-d72af user.warn kernel: r871x_wx_set_pmkid: IW_PMKSA_FLUSH!
Jan  1 00:01:01 WDTV-d72af user.warn kernel: set_mode = IW_MODE_INFRA
Jan  1 00:01:01 WDTV-d72af user.warn kernel: fwdbg:set opmode: 00000000
Jan  1 00:01:01 WDTV-d72af user.warn kernel:
Jan  1 00:01:01 WDTV-d72af user.debug kernel: ir: Enable NEC decoder (0x00000000)
Jan  1 00:01:01 WDTV-d72af user.debug kernel: ir: Enable RC5 decoder (0x00000000)
Jan  1 00:01:01 WDTV-d72af user.warn kernel: set_mode = IW_MODE_INFRA
Jan  1 00:01:01 WDTV-d72af user.warn kernel: fwdbg:set opmode: 00000000
Jan  1 00:01:01 WDTV-d72af user.warn kernel:
Jan  1 00:01:01 WDTV-d72af user.warn kernel:
Jan  1 00:01:01 WDTV-d72af user.warn kernel:  wpa_ie(length:22):
Jan  1 00:01:01 WDTV-d72af user.warn kernel: 0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
Jan  1 00:01:01 WDTV-d72af user.warn kernel: 0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
Jan  1 00:01:01 WDTV-d72af user.warn kernel: 0x00 0x0f 0xac 0x02 0x00 0x00 0x9d 0x93
Jan  1 00:01:01 WDTV-d72af user.warn kernel: +r8711_wx_set_freq  f=976 c=2 wrqu->e=0 wrqu->m=3
Jan  1 00:01:01 WDTV-d72af user.warn kernel: fwdbg:setAuth: 00000002
Jan  1 00:01:01 WDTV-d72af user.warn kernel:
Jan  1 00:01:01 WDTV-d72af user.warn kernel: fwdbg:get join cmd
Jan  1 00:01:01 WDTV-d72af user.warn kernel:
Jan  1 00:01:02 WDTV-d72af user.warn kernel: fwdbg:cur channel: 00000003, bcn interval: 00000064
Jan  1 00:01:02 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:link to Broadcom AP
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:issue auth
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:issue assocreq(00000047)
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:mac id #5: 0000005b, 100fffff, 00000007
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:join res(00000003, 0000020c)
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:07 WDTV-d72af user.warn kernel: [got_addbareq_event_callback] mac = 30 46 9A 51 1D 78, seq = 0, tid = 0
Jan  1 00:01:07 WDTV-d72af user.warn kernel: fwdbg:issue action: 00000003, 00000001, 00000000
Jan  1 00:01:07 WDTV-d72af user.warn kernel:
Jan  1 00:01:08 WDTV-d72af user.warn kernel: fwdbg:rcv set_stakey
Jan  1 00:01:08 WDTV-d72af user.warn kernel:
Jan  1 00:01:12 WDTV-d72af user.info kernel: NTFS volume version 3.1.
Jan  1 00:01:14 WDTV-d72af user.notice mount.watch: Unmounting official device /tmp/media/usb/SKYDRVx2
Jan  1 00:01:14 WDTV-d72af daemon.notice ntfs-3g[446]: Unmounting /dev/sda1 (SKYDRVx2)
Jan  1 00:01:14 WDTV-d72af daemon.notice ntfs-3g[1938]: Version 2009.4.4 integrated FUSE 27
Jan  1 00:01:14 WDTV-d72af daemon.notice ntfs-3g[1938]: Mounted /dev/sda1 (Read-Write, label "SKYDRVx2", NTFS 3.1)
Jan  1 00:01:14 WDTV-d72af daemon.notice ntfs-3g[1938]: Cmdline options: force
Jan  1 00:01:14 WDTV-d72af daemon.notice ntfs-3g[1938]: Mount options: force,silent,allow_other,nonempty,relatime,fsname=/dev/sda1
Title: Re: *experimental* wireless usb support package
Post by: vdc on August 17, 2011, 08:42:05 AM
Hi, I wonder if someone can help me:
I have modded my WDTV Gen 1 to WDLXTV 0.5.8.1
Now I am trying to get a wireless adaptor to work.

I have two wireless adaptors - (Both TP-Link) TL-WN821Nv3 and TL-WN722N. They are both Atheros I think, and I don't mind which I can use.

My wireless is 802.11n on ch1 with WPA2-PSK, the SSID is POKEMON and the PSK is 12345678 (for this example). DHCP is enabled on my router.

Here's what i've got so far:
http://i55.tinypic.com/jpg4ms.jpg

The wireless adaptors don't even blink, and I can tell from my router that they are not connected.

Can anybody help? I have been trying to read guides but it is Chinese to me.

Thanks :)
Title: Re: *experimental* wireless usb support package
Post by: Ron[NL] on August 19, 2011, 02:22:51 AM
@vdc,

don't know if you have a usb-ethernet adapter, if you do : please check if the "wireless-mod-wdlxtv.app.bin"is even picked-up/loaded at boot. Use telnet/shh to log in the box.

BTW : is that NEW VOLUME the drive-name of H: ? If it is, please change that name to something without a space in the name. With a space, no app.bin's will load (known bug)
Title: Re: *experimental* wireless usb support package
Post by: rmi on August 24, 2011, 04:42:54 AM

@vdc

it should be "wpa_supplicant -Bw -Dotus -i$MDEV -c/boot/wpa_supplicant.conf" to use the atheros otus driver. However i assume this only works with TL-WN821Nv1(not confirmed) ... i had v2 and it didn't even detected the device in the dmesg output

This guide works like a charm for me
http://wdtvforum.com/main/index.php?topic=6842.0

However you need to use D-Link DWA-140 (Any revision, B1 aka Revision 1 or the newest B2 aka Revision 2)
Title: Re: *experimental* wireless usb support package
Post by: nikola_bb on December 12, 2011, 01:36:29 PM
Can you please help me with the wd gen1 wifi. I have Edimax EW-7318USg and i have wpa2 network i cant connect to it. here are my messages:

netconfig:
Code: [Select]
sleep 2

ifconfig $MDEV up
iwconfig $MDEV essid MyEssid

sleep 2
wpa_supplicant -Bw -Dralink -i$MDEV -c/tmp/mnt/sda1/wpa_supplicant.conf

sleep 2
HOST=wdtv
MTU=9000
DHCP=no
IP=10.0.1.11
GW=10.0.1.2
DNS1=10.0.1.1

sleep 5
and wpa

Code: [Select]
#ctrl_interface=/tmp/wpa_supplicant
network={
ssid="Nikola's Network"
#comment next line if your ap broadcast ssid
scan_ssid=1
key_mgmt=WPA2-PSK
psk="nikolaelenask"
}
Title: Re: *experimental* wireless usb support package
Post by: arfgh on September 06, 2012, 05:22:32 AM

guys, i have a comtrend dongle with zydas 1211 and other one comtrend zydas 1211b

all the attempts that i have performed to connect to a router with wpa-psk, have failed misserability.
I have read tons of forums and threads, and i feel that it is impossible to connect via wpa-psk, because in open mode or wep mode i got success.

I have also a TL-WN821N v2 and v3 but i dont know what mode must use for them wex otus ralink.

can someone throw some light over the gen1 connection with wpa-psk ?

also, what wireless mod i must use ? because exist several.

thx in advance
Title: Re: *experimental* wireless usb support package
Post by: arfgh on September 09, 2012, 12:27:04 PM

Hi again, at finally got the zydas device to work with wpa. But i see some problem related to the static ip.
i can only get ip if use dhcp, using static ip, no way. but why ?

someone can throw some light about this ?

also, can someone to explain how to make to work the TL-WN821N v2 ?

thx in advance
Title: Re: *experimental* wireless usb support package
Post by: colin.p on September 10, 2012, 02:19:51 AM


Can you not have a "persistent" (or static lease) IP for the WDTV using DHCP? I have a cheap DLink router that allows me to assign an IP for anything on the network. Granted I use DD-WRT, but the default DLink firmware allowed static leases. Actually, I have everything assigned it's own IP and so far no issues.
Title: Re: *experimental* wireless usb support package
Post by: arfgh on September 10, 2012, 07:08:46 PM
i have the whole lan using static ips. but for some reasson if i dont enable the dhcp server the wdtv dont get ip...
Title: Re: *experimental* wireless usb support package
Post by: ssk on February 22, 2013, 11:14:04 AM
i use wd tv gen 1
dwl 122
router d-link dir 600 whit wpa/wpa 2


WDLXTV-0.5.8.1
wireless-mod-wdlxtv.app.bin - no boot whit this. - remain whit blue screen
wireless-mod-rt.app.bin - boot  but no ip
the final result  - NO IP

i use dhcp,  static Ip.



can someoane  say if make this configuration to work?

please, help a poor movie watcher :D